Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. MrT
    3. Posts
    • Profile
    • Following 0
    • Followers 0
    • Topics 3
    • Posts 42
    • Best 0
    • Controversial 0
    • Groups 0

    Posts made by MrT

    • RE: DuetWifi 2 and LIS3DH wiring

      HI , I also have a duet wifi2 and just got my self an LIS3DH to try out, I was wondering if it was possible to use other pins then the temp board pins as it is in use already .
      I do not use a screen or so .

      thanks in advance for the help

      Best Regards
      Manuel

      posted in Duet Hardware and wiring
      MrTundefined
      MrT
    • RE: Extruder motors skip steps with pressure advance enabled

      Dear DC42

      in my mgs I was referring to E jerk, I use E400 with pa enabled and it is skipping steps but not in an extreme way, if I disable it no skipping steps. I normally use E1000 a E1500 without pa and working well but with pa I get extreme step skipping

      my Xy Jerk are tuned to have almost no ringing "X900 Y900" I can go to 1200 but then very small ringing start appearing .

      Best Regards
      Manuel

      posted in Tuning and tweaking
      MrTundefined
      MrT
    • RE: Extruder motors skip steps with pressure advance enabled

      Dear

      I was also trying to tune Pressure advance, I also noticed steps being skipped , I did many testing with many different configurations , My conclusion is that PA is skipping steps due to a much to high acceleration on short segments , on a cube of 50x50x50 for exemple I saw no skipping steps but as soon as I use a different model with circular and a grove β€œ for example 6mm in diameter with a grove intersecting with the circle” I start to get losses in steps if I increase my jerk by a lot I get a much reduce loses of steps , but then the other models get under extruded at some places.

      I hope it can help, cause it would be nice to have it working optimally, the shape corners get a much nicer with PA

      Best Regards
      Manuel

      posted in Tuning and tweaking
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear jacksat

      Thanks for your nice explaination. very nice build, if I may ask one more question what slicer are you using ?

      when checking your pictures , I say you have Belgian plate number πŸ™‚ what area you from ? If i may ask don't want to intrude πŸ™‚ I am from Antwerp

      Best regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear dc42
      merci ,thank you, dank u ,xie xie
      I am back printing !!!
      Best regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear Jacksat

      Very nice build !!!!! I also thought of using a much bigger airpump , but the cost is fairly steep πŸ™‚ , after all the testing I did , using compressed air is best for small parts as for biger parts the fans work beter of course it depends how much air you have available πŸ™‚ , during my testing i managed to use both and that gives really nice result , quick cooling near the nozzle and even cooling on the rest of the part .

      I really like you water cooling , you have a much heavier build then me , I used the same material as the ultimaker 2 to build my printer , it s a much lighter build ,

      Do do have an idea how much extra weight it adds on the head ? And do you get resonance to the frame from those big fans from the cooling bloque ?

      I am asking cause for my build i opted for to have as light as possible heads since I use belt drives that is the reason I added the magnetic tool change in the 1st place , after tying many printer from my friend and so I figured out that ultimaker got very nice and repeatable prints , I figured that one of the reasons is the lightnest of the axes and head

      I am not sure but from ur pictures looks like I using like a buildtalk on you table , I am wondering how good is the result with the dc42 ir prob ? I am using the prob and got a buildtalk plate but have not tried it yet πŸ™‚
      Best regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Once again you are right got over exited to have my printer working again , and was to quick to post,
      pls accept my apologies

      Thanks again for your support
      Best Regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear DC42

      I found an other issue , if I cancel a print the tool change macro are not being executed
      to better explain , if I cancel a print and a tool is still loaded , I and I click on the tool to put it back in standby and go back to its parking place , I get no responds

      Best regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      I have tried some similar approach some time ago without much success I was clogging my nozzle 2 often with the retract , then I just dropped it. since I have limited time for my hobbies 😞
      If you don't mind could you post some picture just for my curiosity πŸ™‚

      Best Regards
      MT

      Ps if you intrested something I have tested with great success ,the use of compressed air for cooling the part during printing , for small part worked miracles only problem was the amount of air used and the noise, my neighbor became crazy , the compressor was working to much and for to long :-). so reverted to the traditional fan,

      the advantaged was less weight on the head and vibration was reduced ,not that there is a lot of vibration , but any improvement is an improvement how ever small πŸ™‚

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      foehnsturm

      do you use something similar to mark2 for your tool change ?

      Best Regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear DC42 & foehnsturm

      Seems foehnsturm is correct !!
      I have tried to add the last line of tpre1 2 times and it seems to work πŸ™‚
      If I may ask what slicer are you guys using ?
      thanks to both of you
      Best Regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear foehnsturm

      I am also using a magnetic tool change , with the 1.18 firmware I can confirm that all is working well ,
      I never managed to get 1.19 working ,since I always had the wrong tool active. did you experience something similar ?
      The issue with wrong tool being active got solved with the latest 1.2 beta4 but I am still facing some issues with the tpre file as it is not fully executed.

      Best Regards
      MT

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear DC42
      just to see what happens I have let the printer continue to print

      the behavior is as follow
      start printing
      T0 is loaded waiting till it reaches temp , start 1 layer
      T0 is parked Tfree fully executed
      T1 is in the process of being loaded the gcode executes to the 5th line of the tpre, and stops there
      then remains there till the nozzle reaches the temperature ,
      once the temperature is reached it continues to print , without the tool being loaded , but the tool is active like it should .
      once the layer without loaded tool is completed it executes Tfree1 successfully
      Then execute tpre0 successfully and tool0 is correctly loaded wait for temp to be reached and start printing.

      hope it will help u to find the glitch

      Best Regards
      Manuel Topiol

      I have put back the 1.18 firmware and the switching is back to normal no stopping at T1 command

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      πŸ™‚ you are right

      the ; was missing , but it has always been missing cause I did not edit the file πŸ™‚
      the error msg is gone but the stop in the middle of the tool change remains on T1

      T0 is being parked and collected correctly
      but when it goes back to collect tool1 seems that to stops before finished and immediately wait for the tool to get to temp then continue printing but the tool1 is not loaded

      Thanks
      Best Regards
      Manuel Topiol

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      I will check right away

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear DC42

      There is some improvement and possibly resolved !!!!

      I just updated the firmware as per previous msg
      tried again the tool change, the problem of the 1st boot and T0 command disappeared, then I did a T1 command and I got an error MSG Error: Bad command: Lift Z relatively to current position
      I removed the Z lift command and now when I change tools the correct tool is active πŸ™‚
      some thing strange is that the z lift is the same in pre0 then in pre1 but the error is only appearing in T1
      Best Regards
      Manuel Topiol

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      for info
      Firmware Name: RepRapFirmware for Duet WiFi
      Firmware Electronics: Duet WiFi 1.0
      Firmware Version: 1.20beta4 (2017-10-28)
      WiFi Server Version: 1.20beta2
      Web Interface Version: 1.19.3

      best regards

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Dear I have done the update of the firmware per your request

      Situation is the same with a slight difference
      now when I select tool 0 from a fresh machine boot , it doesn't complete the full tool change, the gcode file is not fully processed,
      as opposed to before I could just type T0 and it will collect the tool without problem .

      after I put the T0 back in standby and do an other T0 I will get it correctly ,
      then I do a T1 command and it will fetch tool1 but after the selection is complete T0 is set to active.

      , I feel strange, for sure I am not the only guy owning a duet wifi with a tool change, but no one else is complaining about this problem

      Best Regards
      Manuel Topiol

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      Good evening

      Thanks for the quick responds

      I will update the firmware to 1.20beta 2 1st thing in the morning and revert with result

      Best Regards
      Manuel

      posted in General Discussion
      MrTundefined
      MrT
    • RE: Tool change issues after firmware update 1.19.2

      dear DC42

      Hope you had a successful trade show saw some videos on YouTube πŸ™‚ next year I will try to come , if time permits
      I was overseas for some time, just came back .

      So nothing changed to my situation , so I am coming back to you πŸ™‚

      Best Regards
      Manuel Topiol

      posted in General Discussion
      MrTundefined
      MrT