Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. Swanny
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 12
    • Best 0
    • Controversial 0
    • Groups 0

    Swanny

    @Swanny

    0
    Reputation
    1
    Profile views
    12
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    Swanny Unfollow Follow

    Latest posts made by Swanny

    • RE: to ground

      @droftarts

      1. The europian warranty is 2 years.
      2. the wiring and extrudermotor have been replaced.
      3. so the story about shafing and bending is not in place.
      4. The same error (and thats coming from the duet) when switching the extruder motor happend.
      5. the motor stering from extruder one is connected to extruder 2 from the duet. causes motor 2 to fail so saying that it is the motor or motor wiring is false.
      6. If you sell in europe you have to follow the europian rules.

      I like to here from you.

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      january 2020

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux
      E3D-Online
      Unit 35A, Monument Bus Pk
      Chalgrove, Oxfordshire
      OX44 7RW
      United Kingdom

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux
      The problem did follow the extruder motor. The reported error was the same.
      about wiring: it was working perfect for a long period. So the wiring cannot be the problem.

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux
      The extruder motor has a connector and has been delivered with ready wiring with connectors installed.
      making a mistake is not possible.
      and indead always the same error: short to ground error for driver 3

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux

      I switched the wiring from extruder 1 (the problem) to extruder 2 and the wiring from extruder 2 to extreuder one.
      By testing both extruders extruder one workt perfect again.
      extruder 2 had the problem now.
      The error message was the same.
      so the problem followed the extrudermotor.
      error message: short-to-ground reported by driver(s) 3

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @swanny

      wiring switched. behavior and error the same one the other working extruder.
      So changing the wiring replaces the error to the other extruder but the same error message still occurs.

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux
      going to try that this weekend.

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • RE: to ground

      @phaedrux
      on the command M98 P"config.g" i get:
      M98 P"config.g"
      HTTP is enabled on port 80
      FTP is disabled
      TELNET is disabled

      M122.docx

      config.g.docx

      posted in My Duet controlled machine
      Swannyundefined
      Swanny
    • to ground

      Re: Driver 3: short-to-ground

      To avaid a lot of confusing I placed a new extruder motor en replaced the wiring.

      It has the same result:

      The extrudermotor gives an error after about 30/60 seconds.
      if it takes a little bit longer now a fase B error is also displayed.
      Warning: motor phase B may be disconnected reported by driver(s) 3
      The extruder motor switches in about 2-4 times a second from CC to CCC.
      My other 3 extruders on the toolchanger act normally

      What is the solution?

      posted in My Duet controlled machine driver3
      Swannyundefined
      Swanny