@falcounet merci beaucoup pour votre aide.
Posts made by Thomas25
-
RE: Passage de 3.1 au dernier soucisposted in My Duet controlled machine
-
RE: Passage de 3.1 au dernier soucisposted in My Duet controlled machine
@alankilian bonjour, J ai une duet wifi 1.02, J avais mis le firmware 3.01 rc11. La carte pilote mon imprimante hypercube ngen, une core xy. Avant d avoir essayé de passé la dernière version de rff J arrivais à imprimer. Depuis elle de référence plus et le wifi ne fonctionne plus.
-
Passage de 3.1 au dernier soucisposted in My Duet controlled machine
Bonjour, J ai essayé de passé au dernier firmware mais la machine ne fonctionne plus, le wifi n est plus reconnu , J ai alors essayé de le faire via câble ethernet en remplaçant les fichiers firmware mais cela à empiré le problème.
Puis repartir d un fichier complet de ma carte sd puis modifier mes config ?
Ou pourrais je trouver ces fichiers ?
Cordialement Thomas
-
RE: Éteindre le wifiposted in Duet Web Control
@zapta effectivement ça pose soucis et si cela arrive, nous n avons plus de contrôle sûr la machine
-
RE: Éteindre le wifiposted in Duet Web Control
Bonjour, oui je l ai configurer. Du coup J ai résolu le problème en demandant de ne pas ce connecter au réseau
-
Éteindre le wifiposted in Duet Web Control
Bonjour, je travail avec mon imprimante dans mon garage, le WiFi passe très mal et J aimerais utiliser juste le panel duet, comment puis je faire ?
J ai du faire des erreurs lors de mes essais et la machine essai i indéfiniment de ce connecter
-
RE: problem with filament sensorposted in Tuning and tweaking
thank you very much, the sensor is ok. I'm very happy
-
RE: problem with filament sensorposted in Tuning and tweaking
still same issue, whit m591 d0 in console, no run-out filament detecto
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Feb 29 2020 13:14:14 GMT+0100 (heure normale d’Europe centrale) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"ngen thom" ; set printer name M669 K1 ; switch to CoreXY mode ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes backwards M569 P1 S1 ; physical drive 1 goes backwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S1 ; physical drive 3 goes forwards M569 P4 S0 ; physical drive 4 goes backwards M584 X0 Y1 Z2 E3:4 ; set drive mapping M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z800.00 E830.00:830.00 ; set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2) M906 X1100 Y1100 Z1400 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X300 Y330 Z300 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop ; Z-Probe M950 S0 C"exp.8" ; create servo pin 0 for BLTouch M558 P9 C"zprobe.in+zprobe.mod" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X35 Y2 Z1.7 ; set Z probe trigger value, offset and trigger height M557 X15:300 Y15:300 S30 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ;Pressure Advance M572 D0 S0.2 ;enable pressure advance ;Jerk M566 X720 Y720 Z20 E400 ;jerk ; Tools M563 P0 D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C ;M568 P0 S1 plus utile dans RRF3 ; enable mixing for tool 0 M567 P0 E0.5:0.5 ;set mixing ratios for tool 0 ; Bed temperature M140 S0 R0 ; Set initial bed active and standby temperatures to 0C ; run-out filament detector M591 D0 P2 C"zstop" S1 ; sensor for extruder 0, simple sensor (low signal when filament present) on Z endstop ; Automatic saving after power loss is enabled M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Calibrate MCU Temperature M912 P0 S6.0 ; calibrate CPU temperature ; Custom settings are defined M501 -
RE: problem with filament sensorposted in Tuning and tweaking
M591 d0 in duet contrôle "extrudeur has no filament sensor"
-
problem with filament sensorposted in Tuning and tweaking
Hi
I did not manage to install the filament sensor on my machine. My machine is a core xy and see attached my configuration.
the sensor powers on and switches on the mother board led light when it actions. Should I modify another folder ?
Thanks in advance for wour help.
Thomas; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v2.1.8 on Sat Feb 29 2020 13:14:14 GMT+0100 (heure normale d’Europe centrale) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"ngen thom" ; set printer name M669 K1 ; switch to CoreXY mode ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S0 ; physical drive 0 goes backwards M569 P1 S1 ; physical drive 1 goes backwards M569 P2 S0 ; physical drive 2 goes backwards M569 P3 S1 ; physical drive 3 goes forwards M569 P4 S0 ; physical drive 4 goes backwards M584 X0 Y1 Z2 E3:4 ; set drive mapping M350 X16 Y16 Z16 E16:16 I1 ; configure microstepping with interpolation M92 X160.00 Y160.00 Z800.00 E830.00:830.00 ; set steps per mm M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z180.00 E1200.00:1200.00 ; set maximum speeds (mm/min) M201 X500.00 Y500.00 Z20.00 E250.00:250.00 ; set accelerations (mm/s^2) M906 X1100 Y1100 Z1400 E800:800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X300 Y330 Z300 S0 ; set axis maxima ; Endstops M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop ; Z-Probe M950 S0 C"exp.8" ; create servo pin 0 for BLTouch M558 P9 C"zprobe.in+zprobe.mod" H5 F120 T6000 ; set Z probe type to bltouch and the dive height + speeds G31 P500 X35 Y2 Z1.7 ; set Z probe trigger value, offset and trigger height M557 X15:300 Y15:300 S30 ; define mesh grid ; Heaters M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0 M143 H0 S120 ; set temperature limit for heater 0 to 120C M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1 M143 H1 S280 ; set temperature limit for heater 1 to 280C M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit ; run-out filament detector M591 D0 P2 C"zstop" S1 ; sensor for extruder 0, simple sensor (low signal when filament present) on Z endstop ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on ;Pressure Advance M572 D0 S0.2 ;enable pressure advance ;Jerk M566 X720 Y720 Z20 E400 ;jerk ; Tools M563 P0 D0 H1 F0 ; Define tool 0 G10 P0 X0 Y0 Z0 ; Set tool 0 axis offsets G10 P0 R0 S0 ; Set initial tool 0 active and standby temperatures to 0C M567 P0 E0.5:0.5 ;set mixing ratios for tool 0 ; Bed temperature M140 S0 R0 ; Set initial bed active and standby temperatures to 0C ; Automatic saving after power loss is enabled M911 S21.0 R23.0 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; Calibrate MCU Temperature M912 P0 S6.0 ; calibrate CPU temperature ; Custom settings are defined M501