Posts made by Tobs94

and my Stall detection did not react anymore since update. No Change between -60 and +60

7.2.2020, 15:44:15 G32
Leadscrew adjustments made: -0.141 -0.114 -0.166, points used 3, deviation before 0.133 after 0.000
7.2.2020, 15:43:27 G32
Leadscrew adjustments made: -0.138 -0.151 -0.140, points used 3, deviation before 0.144 after 0.000
7.2.2020, 15:41:24 G32
Leadscrew adjustments made: -0.069 -0.167 -0.206, points used 3, deviation before 0.141 after 0.000
7.2.2020, 15:40:40 G32
Leadscrew adjustments made: -0.133 -0.130 -0.066, points used 3, deviation before 0.122 after 0.000
7.2.2020, 15:39:26 G32
Leadscrew adjustments made: -0.349 0.038 -0.080, points used 3, deviation before 0.176 after 0.000
7.2.2020, 15:38:36 G32
Leadscrew adjustments made: -1.094 0.434 -0.084, points used 3, deviation before 0.524 after 0.000
7.2.2020, 15:37:52 G32
Leadscrew adjustments made: -2.909 2.198 -0.556, points used 3, deviation before 1.563 after 0.000

still the same problem.. made me so mad. there must be 1 fault anywhere.

bed.g homeall.g config.g

(Next Problem my Fan is now always on and they did not get shown on Web Control after update)

Thanks for help

@Veti @droftarts

Yes that is exactly how it looks like.

@droftarts

Thats it. I forgot a jumper to set on the board. I will uploadt a picture later for anybody who had the same problem.

thanks

@dc42

Yes thats the problem. got only 1Volt on the Powersupply and 3.3v on usb

fixed it with wiring on.

But now my Modul still not running without Usb.

https://forum.duet3d.com/topic/14247/wifi-module-not-starting-on-boot/6

@dc42

help

Im powering with a 24V Power supply. using the internal 5v than

looks like the Modul is not powered without usb connection. i popt out the usb and the modul shut down.

@dc42 said in WiFi module not starting on boot:

G4 P1000

Y added M552 S1 at start-

checked for the rest with strg-f.
everything is clear.

got that same Problem like @alexdotz in 2018.

alexdotzalexdotz 19 Jul 2018, 03:50
I recently got a duet WiFi, had it up and running, and printed a few hundred hours on it, and then it just stopped letting me connect. My friend in computer science helped me try to figure it out and we determined that the WiFi module just wouldn’t turn on when the board would start up, so we couldn’t connect with the web interface. Though the commend line we can manually start the WiFi module, but this obviously isn’t an ideal situation to have to turn it on every time the printer gets turned off. I would really apply any help on getting this solved so I can go back to flipping the power switch and being up and running right away.

Thanks,
Alex

My Wifi Modul works with usb but not without.

Thanks for help.

Yes I have powerd the board by 24v power supply. So I just have to solder the wires green and white too r2 and r3 ?
Should be right ?

@bearer

@bearer i have no PanelDue

I started with Setup the wifi but then i added new reprap software and updated my firmware with usb to fast restart.

With the new config i wanted to work on today but than i broke my usb port.
(The Wifi already do not work on the new config from reprap tool ) think that is normal when you set the sd card by new files

@zapta

there is a Jst port above the usb.

Will it be possible to solder there ?

can you maybe show me a photo where i have to solder the wires. on the 5 little ares or where ?

nobody have an idea how to start the Wifi modul without the usb connection ?

without any victory*

Hey Guys,

I Broke my Usb Port when traveling with my Printer from 1 Desk to the another.

try to set up M587 with S and P parameter and M552 S1 on config with any victory.
Wifi Modul is not even blinking or anything else.

Maybe someone have an idea to help me out ?

Thanks too all.

@Veti

i checked that for 100%

was testing and swaped front left and rear mid and now the test really starts to get bigger differences