Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet Ethernet with 24v fan

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    fan0 cooling duet3d ethernet
    4
    48
    3.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Bewarenundefined
      Bewaren @Phaedrux
      last edited by

      @phaedrux 24V DC fan, 2 pin output, wired up correctly, very confused as to what the issue could be now, the link shows how to use a 12v fan on a 24v output as far as I can tell, but I am very new to the technical terms used so may be misinterpreting it.

      Phaedruxundefined 1 Reply Last reply Reply Quote 0
      • Bewarenundefined
        Bewaren @Phaedrux
        last edited by

        @phaedrux Tried 3 different fans now, none of them worked, ideas?

        1 Reply Last reply Reply Quote 0
        • Bewarenundefined
          Bewaren @Phaedrux
          last edited by

          @phaedrux one thing I have noticed is the hotend cooling fan on the heat sink is in fact 12v and does function correctly but seems to be running faster than anticipated, when powered via 12v it is significantly slower than the current setup, so I am assuming it is a 24v output from the board however unsure as to how this is happening as I would imagine it would break the fan

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @Bewaren
            last edited by

            @bewaren said in Duet Ethernet with 24v fan:

            @phaedrux 24V DC fan, 2 pin output, wired up correctly, very confused as to what the issue could be now, the link shows how to use a 12v fan on a 24v output as far as I can tell, but I am very new to the technical terms used so may be misinterpreting it.

            You need a buck converter to supply a 12v line into the v_fan jumper pin. But then all your fans need to be 12v.

            If you have some 24v and some 12v you're going to have some issues. The hotend fan is being over volted and while it is working now it's likely to burn out when you least want it to happen.

            Make sure the fans are all the same voltage and supply them with the correct voltage. It's as simple as that.

            Z-Bot CoreXY Build | Thingiverse Profile

            Bewarenundefined 1 Reply Last reply Reply Quote 0
            • Bewarenundefined
              Bewaren @Phaedrux
              last edited by

              @phaedrux Alright ill order a 24v fan for the hotend heatsink to solve that issue then, so any idea on what else I could try to get the print fan working?, it's 24v, I've tried 3 of them now with no luck on the always on pins and the fan0 to fan2 pins, I'm certain it isn't the fans them selves, the pins work fine when I try power the 12v fan but they over voltage the fan, however the 24v fan simply doesn't do anything. Suggestions?

              Phaedruxundefined deckingmanundefined 2 Replies Last reply Reply Quote 0
              • Phaedruxundefined
                Phaedrux Moderator @Bewaren
                last edited by

                @bewaren said in Duet Ethernet with 24v fan:

                Suggestions?

                What exactly is your M106 fan command in config.g right now?
                If you send M106 P0 S1 H-1 in the gcode console does it turn on?

                Z-Bot CoreXY Build | Thingiverse Profile

                Bewarenundefined 1 Reply Last reply Reply Quote 0
                • deckingmanundefined
                  deckingman @Bewaren
                  last edited by

                  @bewaren You also need to have tool selected. The easiest way to do that is to add T0 to the end of your config.g file.

                  Ian
                  https://somei3deas.wordpress.com/
                  https://www.youtube.com/@deckingman

                  dc42undefined Bewarenundefined 2 Replies Last reply Reply Quote 0
                  • dc42undefined
                    dc42 administrators @deckingman
                    last edited by dc42

                    @deckingman said in Duet Ethernet with 24v fan:

                    @bewaren You also need to have tool selected. The easiest way to do that is to add T0 to the end of your config.g file.

                    If the print cooling fan is connected to the Fan0 output, you don't need to select a tool to run it.

                    @Bewaren, does the fan run if you connect it to an always-on fan output?

                    M106 P0 S0.1 I0 F500 H T45 ; Set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on

                    That line in config.g was wrong. The H without a number after it will be interpreted as H0. Remove the H, or change it to H-1.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    Bewarenundefined 1 Reply Last reply Reply Quote 0
                    • Bewarenundefined
                      Bewaren @Phaedrux
                      last edited by

                      @phaedrux M106 P0 S0 I0 F500 H-1 this is my current fan command

                      1 Reply Last reply Reply Quote 0
                      • Bewarenundefined
                        Bewaren @deckingman
                        last edited by

                        @deckingman Tool is selected yes, still nothing though

                        1 Reply Last reply Reply Quote 0
                        • Bewarenundefined
                          Bewaren @dc42
                          last edited by

                          @dc42 M106 P0 S0 I0 F500 H-1 is the line now, still no luck, it also doesn't work even when connected to the always-on fan outputs, but I have tried 3 different fans, all brand new, very unlikely all 3 are faulty.

                          1 Reply Last reply Reply Quote 0
                          • Bewarenundefined
                            Bewaren
                            last edited by

                            @phaedrux Tried sending M106 P0 S1 H-1, it did nothing

                            1 Reply Last reply Reply Quote 0
                            • Bewarenundefined
                              Bewaren
                              last edited by

                              Tried another pack of 24v fans and a 12v fan, 12v fan was over voltaged but worked, 24v fans did nothing, is there somewhere I have to define that the fans I am using are 24v?

                              Phaedruxundefined dc42undefined 2 Replies Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator @Bewaren
                                last edited by

                                @bewaren it really seems like the 24v fans are dead.

                                Can you setup a test with just power from the 24v PSU directly to the fans to remove the duet completely from the equation?

                                If the 12v fans work but the 24v don't then it must be the 24v fan that isn't working. You can carefully measure the voltage on the fan pins to verify.

                                Z-Bot CoreXY Build | Thingiverse Profile

                                1 Reply Last reply Reply Quote 0
                                • dc42undefined
                                  dc42 administrators @Bewaren
                                  last edited by

                                  @bewaren said in Duet Ethernet with 24v fan:

                                  Tried another pack of 24v fans and a 12v fan, 12v fan was over voltage but worked, 24v fans did nothing, is there somewhere I have to define that the fans I am using are 24v?

                                  Are you sure that you have the VFAN jumper set to VIN, not to 5V?

                                  Duet WiFi hardware designer and firmware engineer
                                  Please do not ask me for Duet support via PM or email, use the forum
                                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                                  Bewarenundefined 1 Reply Last reply Reply Quote 0
                                  • Bewarenundefined
                                    Bewaren @dc42
                                    last edited by

                                    @dc42 I am unsure, what pins should I have the jumper on?, its currently on the two right hand pins if looking at it from: https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/YN2oahyGpcPNN1Pw.huge | assuming that the jumper in question is the 3 pin one central to the 5 fan pins.

                                    dc42undefined 1 Reply Last reply Reply Quote 0
                                    • dc42undefined
                                      dc42 administrators @Bewaren
                                      last edited by

                                      @bewaren said in Duet Ethernet with 24v fan:

                                      @dc42 I am unsure, what pins should I have the jumper on?, its currently on the two right hand pins if looking at it from: https://d17kynu4zpq5hy.cloudfront.net/igi/duet3d/YN2oahyGpcPNN1Pw.huge | assuming that the jumper in question is the 3 pin one central to the 5 fan pins.

                                      That's correct, it's the right hand position if you are looking at the Duet with the stepper motor outputs at the top.

                                      To state the obvious: are you sure that the Duet is receiving 24V? If you send M122 to the Duet, the diagnostic report will include the VIN voltage.

                                      Duet WiFi hardware designer and firmware engineer
                                      Please do not ask me for Duet support via PM or email, use the forum
                                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                                      Bewarenundefined 1 Reply Last reply Reply Quote 0
                                      • Bewarenundefined
                                        Bewaren @dc42
                                        last edited by

                                        @dc42 M122
                                        === Diagnostics ===
                                        RepRapFirmware for Duet 2 WiFi/Ethernet version 2.03 running on Duet Ethernet 1.02 or later
                                        Board ID: 08DGM-917DA-G4MSD-6JKDA-3SN6Q-TST39
                                        Used output buffers: 3 of 24 (6 max)
                                        === RTOS ===
                                        Static ram: 25680
                                        Dynamic ram: 93280 of which 380 recycled
                                        Exception stack ram used: 260
                                        Never used ram: 11472
                                        Tasks: NETWORK(ready,652) HEAT(blocked,1236) MAIN(running,3780) IDLE(ready,160)
                                        Owned mutexes:
                                        === Platform ===
                                        Last reset 00:00:19 ago, cause: power up
                                        Last software reset at 2019-07-29 14:33, reason: User, spinning module GCodes, available RAM 11472 bytes (slot 3)
                                        Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0441f000 BFAR 0xe000ed38 SP 0xffffffff Task 0x4e49414d
                                        Error status: 0
                                        Free file entries: 10
                                        SD card 0 detected, interface speed: 20.0MBytes/sec
                                        SD card longest block write time: 0.0ms, max retries 0
                                        MCU temperature: min -64.2, current -57.9, max -57.9
                                        Supply voltage: min 16.7, current 16.9, max 17.0, under voltage events: 0, over voltage events: 0, power good: yes
                                        Driver 0: standstill, SG min/max not available
                                        Driver 1: standstill, SG min/max not available
                                        Driver 2: standstill, SG min/max not available
                                        Driver 3: standstill, SG min/max not available
                                        Driver 4: standstill, SG min/max not available
                                        Date/time: 2019-07-29 17:01:52
                                        Cache data hit count 44910390
                                        Slowest loop: 1.10ms; fastest: 0.07ms
                                        I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                        === Move ===
                                        Hiccups: 0, FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                        Bed compensation in use: none, comp offset 0.000
                                        === DDARing ===
                                        Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0
                                        === Heat ===
                                        Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1
                                        === GCodes ===
                                        Segments left: 0
                                        Stack records: 2 allocated, 0 in use
                                        Movement lock held by null
                                        http is idle in state(s) 0
                                        telnet is idle in state(s) 0
                                        file is idle in state(s) 0
                                        serial is idle in state(s) 0
                                        aux is assembling a command in state(s) 0
                                        daemon is idle in state(s) 0
                                        queue is idle in state(s) 0
                                        autopause is idle in state(s) 0
                                        Code queue is empty.
                                        === Network ===
                                        Slowest loop: 4.33ms; fastest: 0.02ms
                                        Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0) Telnet(0)
                                        HTTP sessions: 1 of 8
                                        Interface state 5, link 100Mbps full duplex

                                        1 Reply Last reply Reply Quote 0
                                        • Bewarenundefined
                                          Bewaren
                                          last edited by

                                          From what I can tell its getting 17v?, I may be incorrect though

                                          dc42undefined 1 Reply Last reply Reply Quote 0
                                          • dc42undefined
                                            dc42 administrators @Bewaren
                                            last edited by

                                            @bewaren said in Duet Ethernet with 24v fan:

                                            From what I can tell its getting 17v?, I may be incorrect though

                                            Is your mains voltage 120V? If so, check whether your PSU has an input voltage selector switch that is set to 230V.

                                            Duet WiFi hardware designer and firmware engineer
                                            Please do not ask me for Duet support via PM or email, use the forum
                                            http://www.escher3d.com, https://miscsolutions.wordpress.com

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA