Another Predator

Carlo

@Danal
Hi Danal,

Yes I did fit Haydn mag arms length 440.47 mm

Thanks

Carlo

Hi Danal,

These are commented out in the home file for Delta Calibration as per the documentation they are not always commented just at the point of posting.

Thanks

Carlo

@Danal said in Another Predator:

X0Y0Z1

Hi Danal,

Pictures as requested,

X0Y0Z1

X0Y185Z1

![IMG_1348.jpg](/assets/uploads/files/1584435825406-img_1348.jpg

Cheers

Carlo

@Danal

I did an M500 this is the result from config_override.g and now removed M501 from the config.g file

; config-override.g file generated in response to M500 at 2020-03-17 08:37
; This is a system-generated file - do not edit
; Delta parameters
M665 L440.470:440.470:440.470 R221.526 H414.033 B185.0 X0.120 Y0.069 Z0.000
M666 X0.008 Y-1.014 Z1.006 A0.00 B0.00
; Heater model parameters
M307 H0 A90.0 C700.0 D10.0 S1.00 V0.0 B0
M307 H1 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H2 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H3 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H4 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H5 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H6 A340.0 C140.0 D5.5 S1.00 V0.0 B0
M307 H7 A340.0 C140.0 D5.5 S1.00 V0.0 B0
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

Cheers

Danal

Thanks, excellent stuff, I will take a look at all of that.

Danal

@Carlo said in Another Predator:

These are commented out in the home file for Delta Calibration as per the documentation they are not always commented just at the point of posting.

Just to triple confirm: The running file on the printer is going to end with the carriages (approximately) 5mm below the endstop switches, correct?

Carlo

@Danal

Hi Danal,

That's what it's supposed to do but I cant confirm as it homes to the below error so it doesn't bounce.
It used to do as intended but I rolled the firmware back redid the configs via the online tool since these errors.
Note* the height Z-50 is myself trying to move the effector after homing.

Not sure this helps.

Thanks I know its a lot to scan through it is appreciated.

Danal

@Carlo said in Another Predator:

Thanks I know its a lot to scan through it is appreciated.

We will get it going. I appreciate your patience in re-posting stuff for the "new guy" looking into this.

boldnuts

@Carlo Your active high endstops are incorrect, should be M574 X2 Y2 Z2 S1 ; Set active high endstops.
It also looks like you have both RR3 and RR2 configs in your config.g ? file

droftarts

@boldnuts said in Another Predator:

@Carlo Your active high endstops are incorrect, should be M574 X2 Y2 Z2 S1 ; Set active high endstops.
It also looks like you have both RR3 and RR2 configs in your config.g ? file

Good catch! Though you mean 'high end' endstops, as in their position on the printer; the S parameter is for active high/low (describes how the microswitch works).

Ian

boldnuts

yes correct, which version of the firmware is being used? as it's confusing

Carlo

@droftarts said in Another Predator:

M574 X2 Y2 Z2 S1

Great stuff homing now works and endstops offsets now look... correct also
Quick calibrate returns:
M665
Diagonals 440.470:440.470:440.470, delta radius 221.612, homed height 414.196, bed radius 185.0, X 0.073°, Y 0.055°, Z 0.000°
M666
Endstop adjustments X-0.03 Y-0.29 Z0.32, tilt X0.00% Y0.00%

Thank you!

Carlo

@boldnuts

Hi Ian,

M115
FIRMWARE_NAME: RepRapFirmware for Duet 2 WiFi/Ethernet FIRMWARE_VERSION: 2.05 ELECTRONICS: Duet Ethernet 1.02 or later FIRMWARE_DATE: 2019-12-13b1

If that still needed.

Thanks

boldnuts

@Carlo can we see your start gcode from your slicer?, you using G32 (calibrate) before printing?, maybe G29 S1 to load the bed mesh?

Carlo

@boldnuts
I have no start code yet having failed to get a layer down yet didn't want to add any complications,
However I have been doing G92 Z0 with paper G32 before attempting aprint ..I never home after probe and always with heated bed and nozzle, bed @ 70c nozzle @ 220c.
I have done the mesh but don't use it .. more to know it's flat..ish I think?? height maps are above in previous post.

If that help ?

Thanks

boldnuts

You need to run G32 in your start gcode before every print and it might be a good idea to run G29 to load the bed mesh as well, then recall it with G29 S1

Danal

@boldnuts said in Another Predator:

You need to run G32 in your start gcode before every print

YES!

This is one of the big keys to running a delta. Let it find the bed, every time.

Carlo

@boldnuts

I'll try the mesh I do G32 before every print attempt.
dc42 commented a well built delta doesn't need bed mesh so not wanted to ..because I want a well built delta printer

Thanks

Carlo

@Danal @boldnuts
This is the height map it just finished ...is it ok?

Thanks

Danal

Yes, that's great. Very flat. RMS error .027.

You can probably skip mesh, if you wish. I would still run a simple probe before every print to set bed height. They run very quickly, in the grand scheme of things.

Here's my bed.g (invoked by G32 in slicer startup code). Note: The M106 commands turn off (and back on) the hotend fan. Mine vibrates enough to cause false triggers. It doesn't hurt for it to be off for the one minute or so all the probes take.

Build one for you here http://escher3d.com/pages/wizards/wizardbed.php The big key is to do a 6 or 8 factor, so as not to adjust diagonal rod length. (Do NOT do a 7 or 9, at least not before every print). More info here: https://duet3d.dozuki.com/Wiki/Calibrating_a_delta_printer#Section_Setting_up_the_bed_g_file

; bed.g file for RepRapFirmware, generated by Escher3D calculator
; 16 points, 8 factors, probing radius: 280, probe offset (0, 0)
G28
M106 P1 S0
G30 P0 X0.00 Y280.00 Z-99999 H0
G30 P1 X140.00 Y242.49 Z-99999 H0
G30 P2 X242.49 Y140.00 Z-99999 H0
G30 P3 X280.00 Y0.00 Z-99999 H0
G30 P4 X242.49 Y-140.00 Z-99999 H0
G30 P5 X140.00 Y-242.49 Z-99999 H0
G30 P6 X0.00 Y-280.00 Z-99999 H0
G30 P7 X-140.00 Y-242.49 Z-99999 H0
G30 P8 X-242.49 Y-140.00 Z-99999 H0
G30 P9 X-280.00 Y-0.00 Z-99999 H0
G30 P10 X-242.49 Y140.00 Z-99999 H0
G30 P11 X-140.00 Y242.49 Z-99999 H0
G30 P12 X0.00 Y140.00 Z-99999 H0
G30 P13 X121.24 Y-70.00 Z-99999 H0
G30 P14 X-121.24 Y-70.00 Z-99999 H0
G30 P15 X0 Y0 Z-99999 S8
G29 S1
M106 P1 S1 I0 F500 H1 T40