Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Connect a Lerdge Power Monitoring Module to the Duet Wifi v1.04?

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    10
    30
    3.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • ediikundefined
      ediik @CrazyCreator
      last edited by

      @CrazyCreator it does not matter. The lerdge board simply gets 5v from the duet and stays on for the time it has 5v connected. No cdg changes necessary. 🙂

      1 Reply Last reply Reply Quote 0
      • CrazyCreatorundefined
        CrazyCreator
        last edited by

        ok ... I would test it

        http://www.crazycreatorcube.com

        1 Reply Last reply Reply Quote 0
        • Meltexundefined
          Meltex @ediik
          last edited by

          @ediik Hi! I came across this thing. 🙂 One question - why don't you use PS_ON signal for controlling Lerdge power module?

          ediikundefined 1 Reply Last reply Reply Quote 0
          • ediikundefined
            ediik @Meltex
            last edited by

            @Meltex hi sorry for late reply. i honestly dont know how to wire it up the right way.

            1 Reply Last reply Reply Quote 0
            • bitminterundefined
              bitminter
              last edited by

              Don’t feel bad this module has beaten me as well for time being. I went to the solid state relay setup as highlighted above and was much simpler to get going with the same button. But... I really would like to figure this out too at some point lol.

              1 Reply Last reply Reply Quote 0
              • bitminterundefined
                bitminter
                last edited by

                Little correction, for me, it’s the Makerbase MKS PWC V2.0 module. No matter what I tried, just couldn’t get it to work.

                1 Reply Last reply Reply Quote 0
                • Richygoatundefined
                  Richygoat
                  last edited by

                  Hello, did anybody the Lerdge Power Modul to work with the Duet. I want to try the same thing. Have a Lerdge Power Modul laying around here. What does the PS_ON pin on the Duet exactly? Act it like a 5v on and off switch?

                  A Former User? 1 Reply Last reply Reply Quote 0
                  • A Former User?
                    A Former User @Richygoat
                    last edited by

                    @Richygoat said in Connect a Lerdge Power Monitoring Module to the Duet Wifi v1.04?:

                    What does the PS_ON pin on the Duet exactly?

                    https://duet3d.dozuki.com/Wiki/Power_Wiring#Section_Controlling_the_external_power_supply

                    1 Reply Last reply Reply Quote 0
                    • Richygoatundefined
                      Richygoat
                      last edited by

                      Here is no answer to this question. I want to turn the PSU off with this modul. When it get 5v continuously from the Duet it stays always on. When there is 5v, GND an PS_ON on that connector how does it exactly work. I know this is 5v in. Does the PS_ON switch the 5V to PS_ON?

                      1 Reply Last reply Reply Quote 0
                      • Richygoatundefined
                        Richygoat
                        last edited by

                        Ok the PS_ON pin will be connected to Ground when the PSU have to be enabled. Is there a way to get a 5v Signal to shut the Relay down? See the picture attached.dr6X10S.png

                        1 Reply Last reply Reply Quote 0
                        • Richygoatundefined
                          Richygoat
                          last edited by

                          Is something like this possible?
                          1586976089952-dr6x10s.png

                          1 Reply Last reply Reply Quote 0
                          • Richygoatundefined
                            Richygoat
                            last edited by

                            This is how it works perfekt. Big thanks to Eryion from Rics 3D Discord.dr6X10S.png

                            CrazyCreatorundefined Ugurundefined 2 Replies Last reply Reply Quote 0
                            • CrazyCreatorundefined
                              CrazyCreator @Richygoat
                              last edited by

                              @Richygoat

                              I edited your sketch and "connected" the switch button. Is that right, did you mean it?1587974008507-dr6x10s.png

                              And a other, next question ...
                              Can you turn off the printer when it is connected via web interface???

                              http://www.crazycreatorcube.com

                              Del87undefined 1 Reply Last reply Reply Quote 0
                              • Richygoatundefined
                                Richygoat
                                last edited by

                                Yes that is correct. The 12V/24V is only for the Button LED. Yes i can turn the Printer via Web Interface off.

                                1 Reply Last reply Reply Quote 0
                                • CrazyCreatorundefined
                                  CrazyCreator
                                  last edited by

                                  thanks for the info

                                  http://www.crazycreatorcube.com

                                  1 Reply Last reply Reply Quote 0
                                  • Del87undefined
                                    Del87 @CrazyCreator
                                    last edited by

                                    @CrazyCreator Hello! Tell me please: what is the white line at the bottom? It is pin connection
                                    between top left on black port and top one on the white? And the black line
                                    between ps_on and module connects central pins?
                                    Thank you in advance for the answer.

                                    Dmitry

                                    1 Reply Last reply Reply Quote 0
                                    • Ugurundefined
                                      Ugur @Richygoat
                                      last edited by

                                      @Richygoat hi, I have panel due with sd card. How i will connect this module?

                                      1 Reply Last reply Reply Quote 0
                                      • First post
                                        Last post
                                      Unless otherwise noted, all forum content is licensed under CC-BY-SA