Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Duet3D Mainboard+Daughter board+PT100

    Scheduled Pinned Locked Moved
    General Discussion
    6
    40
    1.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Reaperrhsundefined
      Reaperrhs @jay_s_uk
      last edited by

      @jay_s_uk i double-check, there is no space, you can see it in my main post, I copy my configuration, the daughterboard is connected on the mainboard duet3d and my sensor is connected to the rtd1 on the daughterboard

      1 Reply Last reply Reply Quote 0
      • Carloundefined
        Carlo
        last edited by Carlo

        Should look like this
        M308 S1 P"spi.cs1" Y"rtd-max31865"
        M950 H1 C"out1" T1

        Working on my duet 3 mainboard

        Reaperrhsundefined 1 Reply Last reply Reply Quote 0
        • Reaperrhsundefined
          Reaperrhs @Carlo
          last edited by

          @Carlo can you show me the hole config for heaters? just to compare with mine

          Carloundefined 1 Reply Last reply Reply Quote 0
          • Carloundefined
            Carlo @Reaperrhs
            last edited by

            @Reaperrhs

            Here you go
            Ignore the bold as that was a temp test with thermistor
            Eveything else is printing really well now on my setup

            ; Configuration file for Duet 3 (firmware version 3)
            ; executed by the firmware on start-up
            ;
            ; generated by RepRapFirmware Configuration Tool v2.1.8 on Mon May 25 2020 14:05:35 GMT+0100 (British Summer Time)

            ; General preferences
            G90 ; send absolute coordinates...
            M83 ; ...but relative extruder moves
            M550 P"Duet 3" ; set printer name
            M665 L440.470 R231.924 H419.252 B185.0 X-0.00 Y-0.00 Z0.000 ; Set delta radius, diagonal rod length, printable radius and homed height
            M666 X0.00 Y0.00 Z0.000 A0.00 B0.00 ; put your endstop adjustments here, or let auto calibration find them

            ; Network
            M552 P192.168.0.25 S1 ; enable network and set IP address
            M553 P255.255.255.0 ; set netmask
            M554 P192.168.0.254 ; set gateway
            M586 P0 S1 ; enable HTTP
            M586 P1 S0 ; disable FTP
            M586 P2 S0 ; disable Telnet

            ; Drives
            M569 P0.0 S0 ; physical drive 0.0 goes backwards
            M569 P0.1 S0 ; physical drive 0.1 goes backwards
            M569 P0.2 S0 ; physical drive 0.2 goes backwards
            M569 P0.3 S0 ; physical drive 0.3 goes backwards
            M584 X0.0 Y0.1 Z0.2 E0.3 ; set drive mapping
            M350 E16 I0 ; configure microstepping without interpolation
            M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
            M92 X160.00 Y160.00 Z160.00 E1837.00 ; set steps per mm
            M566 X1000.00 Y1000.00 Z1000.00 E40.00 ; set maximum instantaneous speed changes (mm/min)
            M203 X18000.00 Y18000.00 Z18000.00 E400.00 ; set maximum speeds (mm/min)
            M201 X1000.00 Y1000.00 Z1000.00 E120.00 ; set accelerations (mm/s^2)
            M906 X1700 Y1700 Z1700 E400 I45 ; set motor currents (mA) and motor idle factor in per cent
            M84 S45 ; Set idle timeout

            ; Axis Limits
            M208 Z-0.5 S1 ; set minimum Z

            ; Endstops
            M574 X2 S1 P"io4.in" ; configure active-high endstop for high end on X via pin io4.in
            M574 Y2 S1 P"io1.in" ; configure active-high endstop for high end on Y via pin io1.in
            M574 Z2 S1 P"io2.in" ; configure active-high endstop for high end on Z via pin io2.in

            ; Z-Probe
            M558 P5 R0.6 C"io3.in+io3.out" H5 F1200 T6000 ; set Z probe type to effector and the dive height + speeds
            G31 P500 X0 Y0 Z-0.17 ; set Z probe trigger value, offset and trigger height
            M557 R170 S20 ; define mesh grid

            ; Heaters
            M308 S0 P"temp0" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin temp0
            M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
            M143 H0 S120 ; set temperature limit for heater 0 to 120C
            M307 H0 A122.0 C513.7 D0.5 S1.00 V24.0 B0 ; disable bang-bang mode for the bed heater and set PWM limit
            M140 H0 ; map heated bed to heater 0
            ;M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
            ;M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
            ;M143 H1 S300 ; set temperature limit for heater 1 to 300C
            ;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

            M308 S1 P"spi.cs0" Y"rtd-max31865" ; configure sensor 1 as thermocouple via CS pin spi.cs0
            M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
            M143 H1 S450 ; set temperature limit for heater 1 to 450C
            M307 H1 A512.3 C269.6 D3.6 S1.00 V24.0 B0 ; disable bang-bang mode for heater and set PWM limit

            ; Fans
            M950 F0 C"out9" Q500 ; create fan 0 on pin out9 and set its frequency
            M106 P0 S0 H-1 C"Part Cooler" ; set fan 0 value. Thermostatic control is turned off
            M950 F1 C"out7" Q250 ; create fan 1 on pin out7 and set its frequency
            M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
            M950 F2 C"out8" Q500 ; create fan 2 on pin out8 and set its frequency
            M106 P2 S0 H-1 C"Berd Air" ; set fan 2 value. Thermostatic control is turned off

            ; Tools
            M563 P0 S"E3D Brass 0.4" D0 H1 F0:2 ; define tool 0
            G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
            G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

            ; Custom settings
            ;Retraction settings
            M207 S1.75 F2800 T1500 Z0.25

            ; Miscellaneous
            M501 ; load saved parameters from non-volatile memory

            Reaperrhsundefined 1 Reply Last reply Reply Quote 0
            • Reaperrhsundefined
              Reaperrhs @Carlo
              last edited by

              @Carlo thanks, let me see what I'm missing (are you using a daughterboard to??)

              Carloundefined 1 Reply Last reply Reply Quote 0
              • Carloundefined
                Carlo @Reaperrhs
                last edited by Carlo

                @Reaperrhs
                Yeah I have the PT100 in 0 which is the right hand terminal as you look at it are you 2 wire or 4 wire?
                if 2 do you have the jumpers on behind the terminals ?

                Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                • Reaperrhsundefined
                  Reaperrhs @Carlo
                  last edited by

                  @Carlo i have two wires, also the jumpers are in place, the two wires are connected in the right hand of the daughterboard

                  Carloundefined 1 Reply Last reply Reply Quote 0
                  • Carloundefined
                    Carlo @Reaperrhs
                    last edited by Carlo

                    @Reaperrhs

                    That's 0 channel, 4 connection block only 2 wire in the 2 center terminals ?

                    Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                    • Reaperrhsundefined
                      Reaperrhs @Carlo
                      last edited by

                      @Carlo yes, center terminals

                      Carloundefined 2 Replies Last reply Reply Quote 0
                      • Carloundefined
                        Carlo @Reaperrhs
                        last edited by

                        @Reaperrhs

                        M308 S1 P"spi.cs0" Y"rtd-max31865"

                        1 Reply Last reply Reply Quote 0
                        • Carloundefined
                          Carlo @Reaperrhs
                          last edited by

                          @Reaperrhs
                          There is a space before the Y M308 S1 P"spi.cs0" Y"rtd-max31865"

                          Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                          • Reaperrhsundefined
                            Reaperrhs @Carlo
                            last edited by

                            @Carlo no luck so far, i have to double-check everything, also.. can you tell me whats define by the S1? because that's the only thing we have different

                            Carloundefined 1 Reply Last reply Reply Quote 0
                            • Carloundefined
                              Carlo @Reaperrhs
                              last edited by

                              @Reaperrhs
                              That's the Sensor number 1 so my bed is Sensor 0 ,hot end single hot end on my setup #1

                              1 Reply Last reply Reply Quote 0
                              • jay_s_ukundefined
                                jay_s_uk
                                last edited by

                                maybe attach a photo of the daughterboard and wiring as you've installed it?

                                Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

                                Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                                • JoergS5undefined
                                  JoergS5
                                  last edited by

                                  and the current heater config please

                                  1 Reply Last reply Reply Quote 0
                                  • Reaperrhsundefined
                                    Reaperrhs @jay_s_uk
                                    last edited by

                                    @jay_s_uk 2020-05-28.png

                                    Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                                    • Reaperrhsundefined
                                      Reaperrhs @Reaperrhs
                                      last edited by

                                      @Reaperrhs ; Heaters

                                      M308 S0 P"spi.cs0" Y"rtd-max31865" ; configure sensor 0 as thermocouple via CS pin spi.cs0
                                      M950 H0 C"out1" T0 ; create nozzle heater output on out1 and map it to sensor 1
                                      M143 H0 S450 ; set temperature limit for heater 1 to 450C
                                      M307 H0 A512.3 C269.6 D3.6 S1.00 V24.0 B0 ; disable bang-bang mode for heater and set PWM limit
                                      M308 S1 P"temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
                                      M950 H1 C"out0" T1 ; create bed heater output on out0 and map it to sensor 1
                                      M143 H1 S280 ; set temperature limit for heater 1 to 280C
                                      M307 H1 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                                      M140 H1

                                      Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                                      • Reaperrhsundefined
                                        Reaperrhs @Reaperrhs
                                        last edited by

                                        @Reaperrhs the one on the top is for my hotend, is the one with the PT100

                                        Carloundefined 1 Reply Last reply Reply Quote 0
                                        • Carloundefined
                                          Carlo @Reaperrhs
                                          last edited by Carlo

                                          @Reaperrhs

                                          Just copy and paste mine in comment your lines out ; line by line so you dont need to delete it

                                          M308 S0 P"temp0" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin temp0
                                          M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
                                          M143 H0 S120 ; set temperature limit for heater 0 to 120C
                                          M307 H0 A122.0 C513.7 D0.5 S1.00 V24.0 B0 ; disable bang-bang mode for the bed heater and set PWM limit
                                          M140 H0 ; map heated bed to heater 0
                                          M308 S1 P"spi.cs0" Y"rtd-max31865" ; configure sensor 1 as thermocouple via CS pin spi.cs0
                                          M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
                                          M143 H1 S450 ; set temperature limit for heater 1 to 450C
                                          M307 H1 A512.3 C269.6 D3.6 S1.00 V24.0 B0 ; disable bang-bang mode for heater and set PWM limit

                                          Reaperrhsundefined 1 Reply Last reply Reply Quote 0
                                          • Reaperrhsundefined
                                            Reaperrhs @Carlo
                                            last edited by

                                            @Carlo HOTEND Working Thanks!!!

                                            Carloundefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA