Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Help me get connected to my Duet2Wifi

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    6
    126
    6.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Vetiundefined
      Veti
      last edited by

      most likely are missing the G30 in your homing files and are trying to hit the none existing endstop

      post your homing files

      1 Reply Last reply Reply Quote 0
      • jay_s_ukundefined
        jay_s_uk
        last edited by

        You need to change your homez and homeall files to something like

        G91 
        G1 H2 Z5
        G90
        G1 X150 Y150
        G30
        

        A probe doesn't use the typical G1 H1 moves to home.
        That code above basically lifts the bed away from the nozzle, moves to a position (usually the centre of the bed so adjust taking into account your probe offset) and then it proves the bed at that point to set Z to whatever your probe offset is.

        Owns various duet boards and is the main wiki maintainer for the Teamgloomy LPC/STM32 port of RRF. Assume I'm running whatever the latest beta/stable build is

        Kwad3dundefined 1 Reply Last reply Reply Quote 0
        • Kwad3dundefined
          Kwad3d @jay_s_uk
          last edited by

          @jay_s_uk Ok that seemed to get me going.

          Now I just have to figure out how to adjust where the mesh starts for each axis. the XY max probe points are perfect at 10mm inside the max points of the bed. However the X is starting at 40mm (62 at the nozzle) and the Y is starting at 55mm.

          Phaedruxundefined 1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @Kwad3d
            last edited by

            @Kwad3d said in Help me get connected to my Duet2Wifi:

            However the X is starting at 40mm (62 at the nozzle) and the Y is starting at 55mm.

            M557 X36:290 Y46:290 S48 ; define mesh grid

            If it's starting too far inside the limit, increase/decrease the limits in M557

            Try X10:290 Y10:290

            To make testing faster, change S48 to P2:2, this would result in a 2x2 grid instead of a full detailed grid. Once you're happy with the extends you can switch back to the spacing method, or increase the number of points.

            https://duet3d.dozuki.com/Wiki/Gcode?revisionid=HEAD#Section_M557_Set_Z_probe_point_or_define_probing_grid

            Z-Bot CoreXY Build | Thingiverse Profile

            Kwad3dundefined 3 Replies Last reply Reply Quote 0
            • Kwad3dundefined
              Kwad3d @Phaedrux
              last edited by

              @Phaedrux Thanks. Yea I'm slowly getting it where I want by making those adjustments. Despite my negative opinion on senseless homing the BL touch setup it way simpler and easier than marlin which continuously tried to probe off the bed regardless of adjustments made.

              1 Reply Last reply Reply Quote 0
              • Kwad3dundefined
                Kwad3d @Phaedrux
                last edited by

                @Phaedrux Seems I got the bed mesh dialed in pretty good. I used previous Hight maps to adjust the bed mounting points and this is my result. Sure its not %100 perfect but I will take it. Hopefully that is the last of the assistance I need. Thanks again for your patience and professionalism fd3ac3e7-943b-43c2-a46c-8292f02b86f9-image.png

                1 Reply Last reply Reply Quote 1
                • Kwad3dundefined
                  Kwad3d @Phaedrux
                  last edited by

                  @Phaedrux So I think Im done setting up the machine. I got a message when sending M500 so save my pid tune saying "Warning: M500: No M501 command was executed in config.g"

                  Do I just add M501 after the last line in config.g or am I good to turn it off now?

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @Kwad3d
                    last edited by

                    @Kwad3d said in Help me get connected to my Duet2Wifi:

                    Do I just add M501 after the last line in config.g

                    Yeah you need to add M501 at the end of config.g to load the saved values at boot from config-override.g.

                    The saved values are still there in config-override.g whether you turn it off or not.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    Kwad3dundefined 1 Reply Last reply Reply Quote 0
                    • Kwad3dundefined
                      Kwad3d @Phaedrux
                      last edited by

                      @Phaedrux Hi again. So I ran into a issue with my bed leveling. When I got the probe grid mapped out for my printer I used the hight map to manually level the bed. I did such a good job that I never noticed that the printer was not compensating for irregularities. I recently changed the build surface and now my mesh is no longer as flat as I posted in the pic. Now Im noticing that the printer is not adjusting the z axis for a good first layer. What to I need to do to turn on leveling based off the generated hight map?

                      1 Reply Last reply Reply Quote 0
                      • Phaedruxundefined
                        Phaedrux Moderator
                        last edited by

                        The heightmap is not loaded at startup automatically. You need to either use G29 to create a fresh map, or use G29 S1 to load the previously created heightmap. That would usually happen in your slicer start gcode after the axis have been homed (and Z has been homed with the probe).

                        Z-Bot CoreXY Build | Thingiverse Profile

                        Kwad3dundefined 1 Reply Last reply Reply Quote 0
                        • Kwad3dundefined
                          Kwad3d @Phaedrux
                          last edited by

                          @Phaedrux Yea I have G29 in my start G code but the Z axis makes no adjustments to follow the mesh. Here is my G code.

                          G28 ; home all axes
                          G29 S1
                          G1 Z5 F3000 ; lift
                          G1 X10 Y10 F1500 ; move to prime
                          G1 Z0.2 F3000 ; get ready to prime
                          G92 E0 ; reset extrusion distance
                          G1 X120 E15 F600 ; prime nozzle
                          G1 X140 F5000 ; quick wipe-

                          1 Reply Last reply Reply Quote 0
                          • Phaedruxundefined
                            Phaedrux Moderator
                            last edited by

                            How are you determining that it's not compensating?

                            If you send M122 after the print is started, does it show "compensation: mesh"?

                            Z-Bot CoreXY Build | Thingiverse Profile

                            1 Reply Last reply Reply Quote 0
                            • Kwad3dundefined
                              Kwad3d
                              last edited by

                              I marked my Z motor's 20T gear with a black line. There is no movement other than adjusting for a new layer. I entered M122 in the console and this is what came back

                              M122
                              === Diagnostics ===
                              RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
                              Board ID: 08DJM-9178L-L4MSJ-6JTD8-3S86L-K826N
                              Used output buffers: 3 of 24 (21 max)
                              === RTOS ===
                              Static ram: 27980
                              Dynamic ram: 93912 of which 52 recycled
                              Exception stack ram used: 648
                              Never used ram: 8480
                              Tasks: NETWORK(ready,268) HEAT(blocked,1224) MAIN(running,1732) IDLE(ready,80)
                              Owned mutexes: WiFi(NETWORK)
                              === Platform ===
                              Last reset 105:28:54 ago, cause: software
                              Last software reset at 2020-12-31 07:13, reason: User, spinning module GCodes, available RAM 8528 bytes (slot 3)
                              Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
                              Error status: 0
                              MCU temperature: min 40.1, current 40.5, max 40.7
                              Supply voltage: min 23.8, current 23.9, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
                              Driver 0: ok, SG min/max 0/126
                              Driver 1: standstill, SG min/max 0/1023
                              Driver 2: standstill, SG min/max not available
                              Driver 3: ok, SG min/max not available
                              Driver 4: standstill, SG min/max not available
                              Date/time: 2021-01-04 16:43:33
                              Cache data hit count 4294967295
                              Slowest loop: 88.77ms; fastest: 0.14ms
                              I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                              === Storage ===
                              Free file entries: 9
                              SD card 0 detected, interface speed: 20.0MBytes/sec
                              SD card longest read time 1.3ms, write time 41.5ms, max retries 0
                              === Move ===
                              Hiccups: 0(0), FreeDm: 166, MinFreeDm: 154, MaxWait: 0ms
                              Bed compensation in use: mesh, comp offset 0.000
                              === MainDDARing ===
                              Scheduled moves: 2501, completed moves: 2493, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: 3
                              === AuxDDARing ===
                              Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
                              === Heat ===
                              Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
                              Heater 0 is on, I-accum = 0.2
                              Heater 1 is on, I-accum = 0.5
                              === GCodes ===
                              Segments left: 1
                              Movement lock held by null
                              HTTP is idle in state(s) 0
                              Telnet is idle in state(s) 0
                              File is doing "G1 X120.948 Y165.948 E2.6605" in state(s) 0
                              USB is idle in state(s) 0
                              Aux is idle in state(s) 0
                              Trigger is idle in state(s) 0
                              Queue is idle in state(s) 0
                              Daemon is idle in state(s) 0
                              Autopause is idle in state(s) 0
                              Code queue is empty.
                              === Network ===
                              Slowest loop: 201.12ms; fastest: 0.09ms
                              Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
                              HTTP sessions: 1 of 8

                              • WiFi -
                                Network state is active
                                WiFi module is connected to access point
                                Failed messages: pending 0, notready 0, noresp 1
                                WiFi firmware version 1.23
                                WiFi MAC address bc:dd:c2:31:a5:92
                                WiFi Vcc 3.40, reset reason Unknown
                                WiFi flash size 4194304, free heap 22840
                                WiFi IP address 192.168.1.10
                                WiFi signal strength -54dBm, reconnections 0, sleep mode modem
                                Socket states: 0 4 0 0 0 0 0 0
                              fcwiltundefined 1 Reply Last reply Reply Quote 0
                              • fcwiltundefined
                                fcwilt @Kwad3d
                                last edited by

                                @Kwad3d said in Help me get connected to my Duet2Wifi:

                                I marked my Z motor's 20T gear with a black line. There is no movement other than adjusting for a new layer. I entered M122 in the console and this is what came back

                                The movement can be very hard to see if you are looking at the gear.

                                Affix a pointer of some sort to magnify the apparent movement. I use a 50mm nail held to the lead screw with a small magnet.

                                Once I did that I could see the mesh adjustments.

                                Frederick

                                Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                Kwad3dundefined 1 Reply Last reply Reply Quote 0
                                • Kwad3dundefined
                                  Kwad3d @fcwilt
                                  last edited by

                                  @fcwilt Its not moving. I have 17 printers in the shop and I can visually see the z axis move when compensating for irregularities in the bed. Also you should be able to feel minor adjustments if you lightly tough the pully on the Z motor as well. I mean I can place a 3mm spacer under the front of the bed where the z is homed to exaggerate a out of level platform to prove its not working but its simply a waste of my time as I can tell its not working. I'm not speculating...

                                  1 Reply Last reply Reply Quote 0
                                  • Phaedruxundefined
                                    Phaedrux Moderator
                                    last edited by

                                    M122 indicates it's active. What does the heightmap image look like? Did you re-create the mesh with G29 after changing the bed surface? Do you have any taper off set with M376?

                                    This thread is very long at this point and this is a completely unrelated issue. It might be a good idea to start a new thread with all your config files, etc

                                    Z-Bot CoreXY Build | Thingiverse Profile

                                    Kwad3dundefined 1 Reply Last reply Reply Quote 0
                                    • Kwad3dundefined
                                      Kwad3d @Phaedrux
                                      last edited by

                                      @Phaedrux So Im having trouble with the Wifi connection again. Guessing my router reset or something. I identified the new address for the board but when I connect it says "Your Duet rejected the HTTP request: overflow". I went through the guide again and also referred to our previous messages on this chain but I can not figure it out. My research only comes up with a SD card problem but nothing changed besides the address on the router

                                      1 Reply Last reply Reply Quote 0
                                      • Phaedruxundefined
                                        Phaedrux Moderator
                                        last edited by

                                        So your router gave the duet a new IP address? Can you set a DHCP reservation in the router so that the duet can keep the same ip long term?

                                        Z-Bot CoreXY Build | Thingiverse Profile

                                        Kwad3dundefined 1 Reply Last reply Reply Quote 0
                                        • Kwad3dundefined
                                          Kwad3d @Phaedrux
                                          last edited by

                                          @Phaedrux said in Help me get connected to my Duet2Wifi:

                                          DHCP reservation

                                          Ok I figured it out and have it reserved

                                          1 Reply Last reply Reply Quote 0
                                          • Phaedruxundefined
                                            Phaedrux Moderator
                                            last edited by

                                            What URL are you using to try and reach the Duet?

                                            Z-Bot CoreXY Build | Thingiverse Profile

                                            Kwad3dundefined 3 Replies Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA