• Tags
  • Documentation
  • Order
  • Register
  • Login
Duet3D Logo Duet3D
  • Tags
  • Documentation
  • Order
  • Register
  • Login

G32 ERROR

Scheduled Pinned Locked Moved
Duet Hardware and wiring
7
108
5.1k
Loading More Posts
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • undefined
    fcwilt @moe.adams9093
    last edited by 2 Feb 2021, 03:43

    @moe-adams9093 said in G32 ERROR:

    M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5stop+!exp.e6stop"
    and run m119 it will show the endstop is triggered at max

    That result indicates that one or more of the end stop sensors is triggered.

    If you could do the following we can find out if one of the end stop sensors is perhaps not working correctly.

    From the DWC console if you issue the M574 to configure just a single end stop the M119 will report it's state independent of any others.

    M574 Z2 S1 P"!exp.e2stop"
    M119

    M574 Z2 S1 P"!exp.e3stop"
    M119

    M574 Z2 S1 P"!exp.e5stop"
    M119

    M574 Z2 S1 P"!exp.e6stop"
    M119

    If would be very helpful to verify that each end stop sensor is working.

    Thanks.

    Frederick

    Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

    undefined 1 Reply Last reply 2 Feb 2021, 03:50 Reply Quote 0
    • undefined
      moe.adams9093 @fcwilt
      last edited by 2 Feb 2021, 03:50

      @fcwilt ok I Will try that now thanks for keeping up with me I truly appreciated

      undefined 1 Reply Last reply 2 Feb 2021, 04:02 Reply Quote 0
      • undefined
        moe.adams9093
        last edited by 2 Feb 2021, 03:59

        @fcwilt I just tried that still same when I do that it will say M119 All at max and they are not even triggered it the same even if I keep ! or I remove. I know for a fact all my endstops function probably because I did install them on the X and Y and they all worked correctly

        undefined 2 Replies Last reply 2 Feb 2021, 04:05 Reply Quote 0
        • undefined
          fcwilt @moe.adams9093
          last edited by 2 Feb 2021, 04:02

          @moe-adams9093 said in G32 ERROR:

          @fcwilt ok I Will try that now thanks for keeping up with me I truly appreciated

          Sometimes the only way to track down a problem is to approach it one little bit at a time.

          We have seemingly discovered an interesting issue with the firmware having difficulty in processing long commands. I've been using 3.1.1 for months and I have never encountered the issue simply because nothing I did needed a long command like that. And now finally we are aware of the issue.

          As you may recall one of my printers has three Z steppers with end stop sensors. Homing worked just fine under 3.1.1.

          I recently upgraded the printer to 3.2.0 and almost immediately began having homing problems where one of the steppers would keep moving even though the end stop sensor had been triggered (they have LEDs).

          I've only begun testing and need to do much more but out of 5 homing attempts 3 failed as described above.

          As part of my testing I reverted to 3.1.1 and 5 out of 5 homing attempts worked.

          I'm confident I will get it sorted and I am equally confident we will get your problem sorted.

          Frederick

          Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

          1 Reply Last reply Reply Quote 0
          • undefined
            fcwilt @moe.adams9093
            last edited by fcwilt 2 Feb 2021, 04:06 2 Feb 2021, 04:05

            @moe-adams9093 said in G32 ERROR:

            @fcwilt I just tried that still same when I do that it will say M119 All at max and they are not even triggered it the same even if I keep ! or I remove. I know for a fact all my endstops function probably because I did install them on the X and Y and they all worked correctly

            I don't understand what you mean when you say "M119 ALL at max" - I am only interested in the status of Z.

            And you did just configure one at a time? The presence or absence of the ! should most assuredly make a difference.

            Frederick

            Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

            1 Reply Last reply Reply Quote 0
            • undefined
              fcwilt @moe.adams9093
              last edited by 2 Feb 2021, 04:09

              @moe-adams9093 said in G32 ERROR:

              @fcwilt I just tried that still same when I do that it will say M119 All at max and they are not even triggered it the same even if I keep ! or I remove. I know for a fact all my endstops function probably because I did install them on the X and Y and they all worked correctly

              Refresh my memory - what sort of end stop sensor hardware do you have on Z?

              Thanks.

              Frederick

              Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

              1 Reply Last reply Reply Quote 0
              • undefined
                moe.adams9093
                last edited by 2 Feb 2021, 04:21

                they are normally close FYSETC and they are exactly the same as my X&Y EndStops they have 3 pins V G S

                1 Reply Last reply Reply Quote 0
                • undefined
                  Phaedrux Moderator @moe.adams9093
                  last edited by 2 Feb 2021, 04:29

                  @moe-adams9093 said in G32 ERROR:

                  @Phaedrux said in G32 ERROR:

                  Yes. M574 Z2 S4

                  so if I can use M574 Z2 S4 how can split the axis and make one at a time when they hit max location. if you have documentation on that please share it

                  That's the point of S4. Stall detection for each motor independently. Check the wiki entry for m574

                  Z-Bot CoreXY Build | Thingiverse Profile

                  1 Reply Last reply Reply Quote 0
                  • undefined
                    moe.adams9093
                    last edited by 2 Feb 2021, 04:49

                    @dc42 could you please take a look at this problem I'm currently facing I will post the latest config files here to make it short as possible and not to have to go to the previous threads.

                    ; Configuration file for Duet WiFi (firmware version 3)
                    ; executed by the firmware on start-up
                    ;
                    ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
                    ; General preferences
                    G90 ; send absolute coordinates...
                    M83 ; ...but relative extruder moves
                    M550 P"DIVINCI-3D (MP4560)" ; set printer name
                    M669 K1 ; select CoreXY mode
                    ; Network
                    M552 P0.0.0.0 S1 ; enable network and acquire dynamic address via DHCP
                    M586 P0 S1 ; enable HTTP
                    M586 P1 S0 ; disable FTP
                    M586 P2 S0 ; disable Telnet
                    ; Drives
                    M569 P10 R1 T2:2:2:2 S1 ; physical drive 0 goes forwards
                    M569 P11 R1 T2:2:2:2 S1 ; physical drive 1 goes forwards
                    M569 P3 S1 ; physical drive 3 goes forwards
                    M569 P4 S1 ; physical drive 4 goes forwards
                    M569 P5 S1 ; physical drive 5 goes Backwards
                    M569 P6 S1 ; physical drive 6 goes Backwards
                    M569 P8 S0 ; physical drive 7 goes Backwards
                    M569 P9 S0 ; physical drive 9 goes backwards
                    M584 X10 Y11 Z5:6:8:9 E3:4 ; set drive mapping
                    M671 X5.0:455.0:455.0:5.0 Y25.0:25.0:455.0:455.0 S14 ; ZBelts Near Locations
                    M350 X32 Y32 Z16 E16:16 I1 ; configure microstepping with interpolation
                    M92 X80.00 Y80.00 Z410.00 E415.00:415.00 ; set steps per mm
                    M566 X900.00 Y900.00 Z12.00 E120.00:120.00 ; set maximum instantaneous speed changes (mm/min)
                    M203 X6000.00 Y6000.00 Z400 E1200.00:1200.00 ; set maximum speeds (mm/min)
                    M201 X500.00 Y500.00 Z40.00 E250.00:250.00 ; set accelerations (mm/s^2)
                    M906 X1800 Y1800 Z1000 E500:500 I30 ; set motor currents (mA) and motor idle factor in per cent
                    M84 S30 ; Set idle timeout
                    ; Axis Limits
                    M208 X0 Y0 Z0 S1 ; set axis minima
                    M208 X460 Y460 Z460 S0 ; set axis maxima
                    M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin !xstop
                    M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin !ystop
                    M574 Z1 S2 ; configure Z-probe endstop for low end on Z
                    M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5Stop+!exp.e6stop" ; configure active-high endstop for High end on Z via pin !ystop
                    ; Z-Probe
                    M558 P1 C"zprobe.in" H25 F600 T6000 ; set Z probe type to unmodulated and the dive height + speeds
                    G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
                    M557 X20:440 Y20:440 S20 ; define mesh grid
                    ; Heaters
                    M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 0 as thermistor on pin bedtemp
                    M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                    M307 H0 A11 C99000 D2000 B1 ; enable bang-bang mode for the bed heater and set PWM limit
                    M140 H0 ; map heated bed to heater 0
                    M143 H0 S120 ; set temperature limit for heater 0 to 120C
                    M308 S1 P"spi.cs1" Y"thermocouple-max31856" ; configure sensor 1 as thermocouple via CS pin spi.cs1
                    M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                    M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    M308 S2 P"spi.cs2" Y"thermocouple-max31856" ; configure sensor 2 as thermocouple via CS pin spi.cs2
                    M950 H2 C"e1heat" T2 ; create nozzle heater output on e1heat and map it to sensor 2
                    M307 H2 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
                    M308 S3 P"duex.e2temp" Y"thermistor" T10000 B3950 ; configure sensor 3 as thermistor on pin duex.e2temp
                    M950 H3 C"duex.e2heat" T3 ; create chamber heater output on duex.e2heat and map it to sensor 3
                    M307 H3 A11 C99000 D2000 B1 ; enable bang-bang mode for the chamber heater and set PWM limit
                    M141 H3 ; map chamber to heater 3
                    ; Fans
                    M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                    M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned on
                    M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                    M106 P1 S1 H2 T45 ; set fan 1 value. Thermostatic control is turned on
                    M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
                    M106 P2 S1 H1:2 T45 ; set fan 2 value. Thermostatic control is turned on
                    ; Tools
                    M563 P0 S"MAIN EXTRUDER" D0 H1 F0 ; define tool 0
                    G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                    G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
                    M563 P1 S"SECOND EXTRUDER" D1 H2 F0 ; define tool 1
                    G10 P1 X0 Y0 Z0 ; set tool 1 axis offsets
                    G10 P1 R0 S0 ; set initial tool 1 active and standby temperatures to 0C
                    ; Custom settings are not defined
                    ; Miscellaneous
                    M575 P1 S1 B57600 ; enable support for PanelDue
                    M501 ; load saved parameters from non-volatile memory
                    M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                    T0 ; select first tool

                    The endstops I have are normally close Active low. when I run my M119 I get this message

                    2/1/2021, 10:27:05 PM: M119: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped

                    even if I remove my( !) on M574 Z2 S1 code still the same M119 Message.

                    here's my homeall.g files

                    ; homeall.g
                    ; called to home all axes
                    ;
                    ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
                    G91 ; relative positioning
                    G1 H1 Z500 F6000 ; lift Z relative to current position
                    G1 H1 X-465 F8000 ; move quickly to X endstop and stop there (first pass)
                    G1 H1 Y-465 F8000 ; move quickly to Y endstop and stop there (first pass)
                    G1 H2 X5 Y5 F6000 ; go back a few mm
                    G1 H1 X-465 F360 ; move slowly to X axis endstop once more (second pass)
                    G1 H1 Y-465 F360 ; then move slowly to Y axis endstop
                    G1 H2 Z-500 F6000;
                    G1 X235 Y235 F6000 ; Prob at Center
                    M558 F600 A1 ; Dive fast once
                    G30 ; probe Z
                    M558 F300 A10 ; Slow second dive with more accuracy
                    G30 ; probe z again

                    so the purpose here all I want when I press home all I want the bed to go to the max side and trigger all 4 endstops to stop all 4 Z axis individually, then to travel back to the Min side and prob using DC42 IR Sensor and home all at the min side.

                    undefined 1 Reply Last reply 2 Feb 2021, 08:03 Reply Quote 0
                    • undefined
                      Veti
                      last edited by 2 Feb 2021, 06:01

                      @moe-adams9093 said in G32 ERROR:

                      M350 X32 Y32 Z16 E16:16 I1 ; configure microstepping with interpolation

                      the duet 2 only supports interpolation at x16. so this statement is incorrect

                      M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5Stop+!exp.e6stop"

                      you have a mistake you wrote e5S and e6s

                      1 Reply Last reply Reply Quote 0
                      • undefined
                        moe.adams9093
                        last edited by 2 Feb 2021, 06:24

                        That's not the issue this I mistakenly uploaded a back up file if you look up on my previous thread I have the correct file even Phaedrux moderator checked it

                        1 Reply Last reply Reply Quote 0
                        • undefined
                          dc42 administrators @fcwilt
                          last edited by dc42 2 Feb 2021, 07:31 2 Feb 2021, 07:30

                          @fcwilt said in G32 ERROR:

                          @Phaedrux said in G32 ERROR:

                          @fcwilt Hmm, wonder why it didnt work for him the first time?

                          I have no idea - this topic has gotten rather long and it's hard to remember it all.

                          Those names you suggested are shorter by one character each which tends to reinforce the idea of a command length limitation.

                          Perhaps you could speed verification of this possibility with direct communication with dc42?

                          Frederick

                          The string buffer that holds the pin name in commands that require a pin name has a limited length. AFAIR it's 50 characters. Does that explain it?

                          As usual, running M98 P"config.g" should reveal if this is causing a problem.

                          Duet WiFi hardware designer and firmware engineer
                          Please do not ask me for Duet support via PM or email, use the forum
                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                          undefined 1 Reply Last reply 2 Feb 2021, 07:40 Reply Quote 0
                          • undefined
                            fcwilt @dc42
                            last edited by 2 Feb 2021, 07:40

                            @dc42 said in G32 ERROR:

                            The string buffer that holds the pin name in commands that require a pin name has a limited length. AFAIR it's 50 characters. Does that explain it?

                            Yes it does as the string in question was 51 characters and the error message showed the last character was missing.

                            So that answers one question in regards to the OP's issues.

                            Thanks very much.

                            Frederick

                            Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                            1 Reply Last reply Reply Quote 0
                            • undefined
                              fcwilt @moe.adams9093
                              last edited by 2 Feb 2021, 08:03

                              @moe-adams9093 said in G32 ERROR:

                              even if I remove my( !) on M574 Z2 S1 code still the same M119 Message.

                              Are you removing the ! from all four pin names?

                              I tried this M574 Z2 S1 P"!exp.e2stop + !exp.e3stop + !exp.e4stop + !exp.e5stop"

                              and M119 yields this: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped

                              I tried this M574 Z2 S1 P"exp.e2stop + exp.e3stop + exp.e4stop + exp.e5stop"

                              and M119 yields this: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped

                              That was with NOTHING connected to the end stop inputs.

                              With your actual devices connected to the end stop inputs...

                              ...the only way BOTH M119s could yield Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped..

                              ...was if some of the Z axis devices were not active (closed) and some of them active (open).

                              FRederick

                              Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                              1 Reply Last reply Reply Quote 0
                              • undefined
                                dc42 administrators
                                last edited by dc42 2 Feb 2021, 10:41 2 Feb 2021, 10:40

                                exp.e2stop etc. are not the same pins as duex.e2stop because the ones on the DueX are routed through the I2C chip.

                                I am increasing the limit to 100 characters in RRF 3.3.

                                Duet WiFi hardware designer and firmware engineer
                                Please do not ask me for Duet support via PM or email, use the forum
                                http://www.escher3d.com, https://miscsolutions.wordpress.com

                                undefined undefined 2 Replies Last reply 2 Feb 2021, 10:51 Reply Quote 0
                                • undefined
                                  dc42 administrators @dc42
                                  last edited by dc42 2 Feb 2021, 10:51 2 Feb 2021, 10:51

                                  PS - I've put a preview build of 3.3beta for Duet WiFi/Ethernet (without SBC) with the 100-character limit at https://www.dropbox.com/sh/qr98k8fbkj5ue0k/AABPawUF99QVzDrheBQBDSxia?dl=0.

                                  Duet WiFi hardware designer and firmware engineer
                                  Please do not ask me for Duet support via PM or email, use the forum
                                  http://www.escher3d.com, https://miscsolutions.wordpress.com

                                  1 Reply Last reply Reply Quote 1
                                  • undefined
                                    fcwilt @dc42
                                    last edited by 2 Feb 2021, 12:17

                                    @dc42 said in G32 ERROR:

                                    exp.e2stop etc. are not the same pins as duex.e2stop because the ones on the DueX are routed through the I2C chip.

                                    I don't understand.

                                    They are listed together under Endstop Inputs for the DueX boards.

                                    Duet 2 Endstop PIn Names.png

                                    Yet there are no notes or markings to suggest that those with the exp.e#stop names are different from those with the duex.e#stop names.

                                    Where is that difference mentioned?

                                    Thanks.

                                    Frederick

                                    Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                                    undefined 1 Reply Last reply 2 Feb 2021, 16:49 Reply Quote 2
                                    • undefined
                                      Phaedrux Moderator @fcwilt
                                      last edited by 2 Feb 2021, 16:49

                                      @fcwilt said in G32 ERROR:

                                      I don't understand.
                                      They are listed together under Endstop Inputs for the DueX boards.

                                      They are listed as possible pins to use. They are not all equivalent in that list. For instance it lists pins on the Duet as well as the Duex. The exp pins are literally the pins on the expansion header, not the duex pins. The duex endstop pins are separate and routed differently.

                                      So originally when using those exp endstop pin names it was never going to work because he wasn't actually using those pins. (he was using the actual duex endstop headers).

                                      If he had 3 z axis motors and endstops instead of 4, we (you) never would have discovered this bug with the overflow.

                                      Z-Bot CoreXY Build | Thingiverse Profile

                                      undefined 1 Reply Last reply 2 Feb 2021, 17:01 Reply Quote 2
                                      • undefined
                                        moe.adams9093
                                        last edited by 2 Feb 2021, 16:56

                                        Ok I'm going to make some tests today and see what I'm going to end up with. I will keep you posted

                                        1 Reply Last reply Reply Quote 0
                                        • undefined
                                          fcwilt @Phaedrux
                                          last edited by fcwilt 2 Feb 2021, 17:25 2 Feb 2021, 17:01

                                          @Phaedrux said in G32 ERROR:

                                          They are listed as possible pins to use. They are not all equivalent in that list.

                                          I had forgotten that was the case. I got distracted by the quest to figure out why the command was getting truncated.

                                          Perhaps you should update the documentation in that regard as there are some existing pin names that are marked with a ***** to reference a note above regarding their behavior.

                                          It wouldn't hurt to point out the difference in these end stop pins in much the same way.

                                          It would be more work but it might be best to have Duet pin names under a Duet heading and Duex pin names under a Duex heading.

                                          Frederick

                                          Printers: a small Utilmaker style, a small CoreXY and a E3D MS/TC setup. Various hotends. Using Duet 3 hardware running 3.4.6

                                          1 Reply Last reply Reply Quote 0
                                          81 out of 108
                                          • First post
                                            81/108
                                            Last post
                                          Unless otherwise noted, all forum content is licensed under CC-BY-SA