Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    G32 ERROR

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    7
    108
    5.1k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • fcwiltundefined
      fcwilt @moe.adams9093
      last edited by fcwilt

      @moe-adams9093 said in G32 ERROR:

      @fcwilt I just tried that still same when I do that it will say M119 All at max and they are not even triggered it the same even if I keep ! or I remove. I know for a fact all my endstops function probably because I did install them on the X and Y and they all worked correctly

      I don't understand what you mean when you say "M119 ALL at max" - I am only interested in the status of Z.

      And you did just configure one at a time? The presence or absence of the ! should most assuredly make a difference.

      Frederick

      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

      1 Reply Last reply Reply Quote 0
      • fcwiltundefined
        fcwilt @moe.adams9093
        last edited by

        @moe-adams9093 said in G32 ERROR:

        @fcwilt I just tried that still same when I do that it will say M119 All at max and they are not even triggered it the same even if I keep ! or I remove. I know for a fact all my endstops function probably because I did install them on the X and Y and they all worked correctly

        Refresh my memory - what sort of end stop sensor hardware do you have on Z?

        Thanks.

        Frederick

        Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

        1 Reply Last reply Reply Quote 0
        • moe.adams9093undefined
          moe.adams9093
          last edited by

          they are normally close FYSETC and they are exactly the same as my X&Y EndStops they have 3 pins V G S

          1 Reply Last reply Reply Quote 0
          • Phaedruxundefined
            Phaedrux Moderator @moe.adams9093
            last edited by

            @moe-adams9093 said in G32 ERROR:

            @Phaedrux said in G32 ERROR:

            Yes. M574 Z2 S4

            so if I can use M574 Z2 S4 how can split the axis and make one at a time when they hit max location. if you have documentation on that please share it

            That's the point of S4. Stall detection for each motor independently. Check the wiki entry for m574

            Z-Bot CoreXY Build | Thingiverse Profile

            1 Reply Last reply Reply Quote 0
            • moe.adams9093undefined
              moe.adams9093
              last edited by

              @dc42 could you please take a look at this problem I'm currently facing I will post the latest config files here to make it short as possible and not to have to go to the previous threads.

              ; Configuration file for Duet WiFi (firmware version 3)
              ; executed by the firmware on start-up
              ;
              ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
              
              ; General preferences
              G90                                                     	; send absolute coordinates...
              M83                                                     	; ...but relative extruder moves
              M550 P"DIVINCI-3D (MP4560)"                             	; set printer name
              M669 K1                                                 	; select CoreXY mode
              
              ; Network
              M552 P0.0.0.0 S1                                        	; enable network and acquire dynamic address via DHCP
              M586 P0 S1                                              	; enable HTTP
              M586 P1 S0                                              	; disable FTP
              M586 P2 S0                                              	; disable Telnet
              
              ; Drives
              M569 P10  R1 T2:2:2:2  S1  									; physical drive 0 goes forwards
              M569 P11  R1 T2:2:2:2  S1  									; physical drive 1 goes forwards
              M569 P3 S1                                             		; physical drive 3 goes forwards
              M569 P4 S1                                              	; physical drive 4 goes forwards
              M569 P5 S1                                              	; physical drive 5 goes Backwards
              M569 P6 S1 													; physical drive 6 goes Backwards
              M569 P8 S0			          								; physical drive 7 goes Backwards 
              M569 P9 S0                                              	; physical drive 9 goes backwards 
              M584 X10 Y11 Z5:6:8:9 E3:4                              	; set drive mapping
              M671 X5.0:455.0:455.0:5.0 Y25.0:25.0:455.0:455.0 S14    	; ZBelts Near Locations                    
              M350 X32 Y32 Z16 E16:16 I1                              	; configure microstepping with interpolation
              M92 X80.00 Y80.00 Z410.00 E415.00:415.00 					; set steps per mm
              M566 X900.00 Y900.00 Z12.00 E120.00:120.00              	; set maximum instantaneous speed changes (mm/min)
              M203 X6000.00 Y6000.00 Z400 E1200.00:1200.00        		; set maximum speeds (mm/min)
              M201 X500.00 Y500.00 Z40.00 E250.00:250.00           		; set accelerations (mm/s^2)
              M906 X1800 Y1800 Z1000 E500:500 I30                     	; set motor currents (mA) and motor idle factor in per cent
              M84 S30                                                 	; Set idle timeout
              
              ; Axis Limits
              M208 X0 Y0 Z0 S1                                        	; set axis minima
              M208 X460 Y460 Z460 S0                                  	; set axis maxima
              
              M574 X1 S1 P"!xstop"                                    		; configure active-high endstop for low end on X via pin !xstop
              M574 Y1 S1 P"!ystop"                                    		; configure active-high endstop for low end on Y via pin !ystop
              M574 Z1 S2 														; configure Z-probe endstop for low end on Z  
              M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5Stop+!exp.e6stop"	; configure active-high endstop for High end on Z via pin !ystop
              
              ; Z-Probe
              M558 P1 C"zprobe.in" H25 F600 T6000                      	; set Z probe type to unmodulated and the dive height + speeds
              G31 P500 X0 Y0 Z2.5                                     	; set Z probe trigger value, offset and trigger height
              M557 X20:440 Y20:440 S20                                	; define mesh grid
              
              
              ; Heaters
              M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 	; configure sensor 0 as thermistor on pin bedtemp
              M950 H0 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
              M307 H0 A11 C99000 D2000 B1                  				; enable bang-bang mode for the bed heater and set PWM limit
              M140 H0                                                 	; map heated bed to heater 0
              M143 H0 S120                                            	; set temperature limit for heater 0 to 120C
              M308 S1 P"spi.cs1" Y"thermocouple-max31856"             	; configure sensor 1 as thermocouple via CS pin spi.cs1
              M950 H1 C"e0heat" T1                                    	; create nozzle heater output on e0heat and map it to sensor 1
              M307 H1 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
              M308 S2 P"spi.cs2" Y"thermocouple-max31856"             	; configure sensor 2 as thermocouple via CS pin spi.cs2
              M950 H2 C"e1heat" T2                                    	; create nozzle heater output on e1heat and map it to sensor 2
              M307 H2 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
              M308 S3 P"duex.e2temp" Y"thermistor" T10000 B3950       	; configure sensor 3 as thermistor on pin duex.e2temp
              M950 H3 C"duex.e2heat" T3                               	; create chamber heater output on duex.e2heat and map it to sensor 3
              M307 H3 A11 C99000 D2000 B1                             	; enable bang-bang mode for the chamber heater and set PWM limit
              M141 H3                                                 	; map chamber to heater 3
              
              ; Fans
              M950 F0 C"fan0" Q500                                    	; create fan 0 on pin fan0 and set its frequency
              M106 P0 S1 H-1                                          	; set fan 0 value. Thermostatic control is turned on                           
              M950 F1 C"fan1" Q500                                    	; create fan 1 on pin fan1 and set its frequency
              M106 P1 S1 H2 T45                                       	; set fan 1 value. Thermostatic control is turned on
              M950 F2 C"fan2" Q500                                    	; create fan 2 on pin fan2 and set its frequency
              M106 P2 S1 H1:2 T45                                     	; set fan 2 value. Thermostatic control is turned on
              
              ; Tools
              M563 P0 S"MAIN EXTRUDER" D0 H1 F0                       	; define tool 0
              G10 P0 X0 Y0 Z0                                         	; set tool 0 axis offsets
              G10 P0 R0 S0                                            	; set initial tool 0 active and standby temperatures to 0C
              M563 P1 S"SECOND EXTRUDER" D1 H2 F0                     	; define tool 1
              G10 P1 X0 Y0 Z0                                         	; set tool 1 axis offsets
              G10 P1 R0 S0                                            	; set initial tool 1 active and standby temperatures to 0C
              
              ; Custom settings are not defined
              
              ; Miscellaneous
              M575 P1 S1 B57600                                       	; enable support for PanelDue
              M501                                                    	; load saved parameters from non-volatile memory
              M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      	; set voltage thresholds and actions to run on power loss
              T0                                                      	; select first tool
              
              
              

              The endstops I have are normally close Active low. when I run my M119 I get this message

              2/1/2021, 10:27:05 PM: M119: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped
              
              

              even if I remove my( !) on M574 Z2 S1 code still the same M119 Message.

              here's my homeall.g files

              ; homeall.g
              ; called to home all axes
              ;
              ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
              G91                     ; relative positioning
              G1 H1 Z500 F6000          ; lift Z relative to current position
              G1 H1 X-465 F8000 ; move quickly to X endstop and stop there (first pass)
              G1 H1 Y-465 F8000 ; move quickly to Y endstop and stop there (first pass)
              G1 H2 X5 Y5 F6000       ; go back a few mm
              G1 H1 X-465 F360        ; move slowly to X axis endstop once more (second pass)
              G1 H1 Y-465 F360        ; then move slowly to Y axis endstop
              G1 H2 Z-500 F6000;
              G1 X235 Y235 F6000      ; Prob at Center 
              M558 F600 A1 		    ; Dive fast once 
              G30			            ; probe Z
              M558 F300 A10 		    ; Slow second dive with more accuracy
              G30			            ; probe z again
              
              

              so the purpose here all I want when I press home all I want the bed to go to the max side and trigger all 4 endstops to stop all 4 Z axis individually, then to travel back to the Min side and prob using DC42 IR Sensor and home all at the min side.

              fcwiltundefined 1 Reply Last reply Reply Quote 0
              • Vetiundefined
                Veti
                last edited by

                @moe-adams9093 said in G32 ERROR:

                M350 X32 Y32 Z16 E16:16 I1 ; configure microstepping with interpolation

                the duet 2 only supports interpolation at x16. so this statement is incorrect

                M574 Z2 S1 P"!exp.e2stop+!exp.e3stop+!exp.e5Stop+!exp.e6stop"

                you have a mistake you wrote e5S and e6s

                1 Reply Last reply Reply Quote 0
                • moe.adams9093undefined
                  moe.adams9093
                  last edited by

                  That's not the issue this I mistakenly uploaded a back up file if you look up on my previous thread I have the correct file even Phaedrux moderator checked it

                  1 Reply Last reply Reply Quote 0
                  • dc42undefined
                    dc42 administrators @fcwilt
                    last edited by dc42

                    @fcwilt said in G32 ERROR:

                    @Phaedrux said in G32 ERROR:

                    @fcwilt Hmm, wonder why it didnt work for him the first time?

                    I have no idea - this topic has gotten rather long and it's hard to remember it all.

                    Those names you suggested are shorter by one character each which tends to reinforce the idea of a command length limitation.

                    Perhaps you could speed verification of this possibility with direct communication with dc42?

                    Frederick

                    The string buffer that holds the pin name in commands that require a pin name has a limited length. AFAIR it's 50 characters. Does that explain it?

                    As usual, running M98 P"config.g" should reveal if this is causing a problem.

                    Duet WiFi hardware designer and firmware engineer
                    Please do not ask me for Duet support via PM or email, use the forum
                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                    fcwiltundefined 1 Reply Last reply Reply Quote 0
                    • fcwiltundefined
                      fcwilt @dc42
                      last edited by

                      @dc42 said in G32 ERROR:

                      The string buffer that holds the pin name in commands that require a pin name has a limited length. AFAIR it's 50 characters. Does that explain it?

                      Yes it does as the string in question was 51 characters and the error message showed the last character was missing.

                      So that answers one question in regards to the OP's issues.

                      Thanks very much.

                      Frederick

                      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                      1 Reply Last reply Reply Quote 0
                      • fcwiltundefined
                        fcwilt @moe.adams9093
                        last edited by

                        @moe-adams9093 said in G32 ERROR:

                        even if I remove my( !) on M574 Z2 S1 code still the same M119 Message.

                        Are you removing the ! from all four pin names?

                        I tried this M574 Z2 S1 P"!exp.e2stop + !exp.e3stop + !exp.e4stop + !exp.e5stop"

                        and M119 yields this: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped

                        I tried this M574 Z2 S1 P"exp.e2stop + exp.e3stop + exp.e4stop + exp.e5stop"

                        and M119 yields this: Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped

                        That was with NOTHING connected to the end stop inputs.

                        With your actual devices connected to the end stop inputs...

                        ...the only way BOTH M119s could yield Endstops - X: not stopped, Y: not stopped, Z: at max stop, Z probe: not stopped..

                        ...was if some of the Z axis devices were not active (closed) and some of them active (open).

                        FRederick

                        Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                        1 Reply Last reply Reply Quote 0
                        • dc42undefined
                          dc42 administrators
                          last edited by dc42

                          exp.e2stop etc. are not the same pins as duex.e2stop because the ones on the DueX are routed through the I2C chip.

                          I am increasing the limit to 100 characters in RRF 3.3.

                          Duet WiFi hardware designer and firmware engineer
                          Please do not ask me for Duet support via PM or email, use the forum
                          http://www.escher3d.com, https://miscsolutions.wordpress.com

                          dc42undefined fcwiltundefined 2 Replies Last reply Reply Quote 0
                          • dc42undefined
                            dc42 administrators @dc42
                            last edited by dc42

                            PS - I've put a preview build of 3.3beta for Duet WiFi/Ethernet (without SBC) with the 100-character limit at https://www.dropbox.com/sh/qr98k8fbkj5ue0k/AABPawUF99QVzDrheBQBDSxia?dl=0.

                            Duet WiFi hardware designer and firmware engineer
                            Please do not ask me for Duet support via PM or email, use the forum
                            http://www.escher3d.com, https://miscsolutions.wordpress.com

                            1 Reply Last reply Reply Quote 1
                            • fcwiltundefined
                              fcwilt @dc42
                              last edited by

                              @dc42 said in G32 ERROR:

                              exp.e2stop etc. are not the same pins as duex.e2stop because the ones on the DueX are routed through the I2C chip.

                              I don't understand.

                              They are listed together under Endstop Inputs for the DueX boards.

                              Duet 2 Endstop PIn Names.png

                              Yet there are no notes or markings to suggest that those with the exp.e#stop names are different from those with the duex.e#stop names.

                              Where is that difference mentioned?

                              Thanks.

                              Frederick

                              Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                              Phaedruxundefined 1 Reply Last reply Reply Quote 2
                              • Phaedruxundefined
                                Phaedrux Moderator @fcwilt
                                last edited by

                                @fcwilt said in G32 ERROR:

                                I don't understand.
                                They are listed together under Endstop Inputs for the DueX boards.

                                They are listed as possible pins to use. They are not all equivalent in that list. For instance it lists pins on the Duet as well as the Duex. The exp pins are literally the pins on the expansion header, not the duex pins. The duex endstop pins are separate and routed differently.

                                So originally when using those exp endstop pin names it was never going to work because he wasn't actually using those pins. (he was using the actual duex endstop headers).

                                If he had 3 z axis motors and endstops instead of 4, we (you) never would have discovered this bug with the overflow.

                                Z-Bot CoreXY Build | Thingiverse Profile

                                fcwiltundefined 1 Reply Last reply Reply Quote 2
                                • moe.adams9093undefined
                                  moe.adams9093
                                  last edited by

                                  Ok I'm going to make some tests today and see what I'm going to end up with. I will keep you posted

                                  1 Reply Last reply Reply Quote 0
                                  • fcwiltundefined
                                    fcwilt @Phaedrux
                                    last edited by fcwilt

                                    @Phaedrux said in G32 ERROR:

                                    They are listed as possible pins to use. They are not all equivalent in that list.

                                    I had forgotten that was the case. I got distracted by the quest to figure out why the command was getting truncated.

                                    Perhaps you should update the documentation in that regard as there are some existing pin names that are marked with a ***** to reference a note above regarding their behavior.

                                    It wouldn't hurt to point out the difference in these end stop pins in much the same way.

                                    It would be more work but it might be best to have Duet pin names under a Duet heading and Duex pin names under a Duex heading.

                                    Frederick

                                    Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                    1 Reply Last reply Reply Quote 0
                                    • moe.adams9093undefined
                                      moe.adams9093
                                      last edited by

                                      Yeah I'm going to try 3.3 and do duex.e2stop all the way to duex.e6stop and see how its going to behave

                                      1 Reply Last reply Reply Quote 1
                                      • moe.adams9093undefined
                                        moe.adams9093
                                        last edited by

                                        @dc42 So I went ahead and did an update to 3.3. I have 2 problems now My driver Number 10 is an external driver it doesn't move at all it's getting a signal because it locks but no movement in any direction and regarding endstops still the same issue. I will post

                                        config. g

                                        homall. g

                                        M119

                                        M122

                                        M98P"config. g"


                                        config. g

                                        ; Configuration file for Duet WiFi (firmware version 3)
                                        ; executed by the firmware on start-up
                                        ;
                                        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Feb,04,2021 12:48.00 GMT-0500 (Central Daylight Time)
                                        
                                        ; General preferences
                                        G90                                                     	; send absolute coordinates...
                                        M83                                                     	; ...but relative extruder moves
                                        M550 P"DIVINCI-3D (MP4560)"                             	; set printer name
                                        M669 K1                                                 	; select CoreXY mode
                                        
                                        ; Network
                                        M552 P0.0.0.0 S1                                        	; enable network and acquire dynamic address via DHCP
                                        M586 P0 S1                                              	; enable HTTP
                                        M586 P1 S0                                              	; disable FTP
                                        M586 P2 S0                                              	; disable Telnet
                                        
                                        ; Drives
                                        M569 P10  R1 T2:2:2:2  S1  									; physical drive 0 goes forwards
                                        M569 P11  R1 T2:2:2:2  S1  									; physical drive 1 goes forwards
                                        M569 P3 S1                                             		; physical drive 3 goes forwards
                                        M569 P4 S1                                              	; physical drive 4 goes forwards
                                        M569 P5 S1                                              	; physical drive 5 goes Forwards
                                        M569 P6 S1 													; physical drive 6 goes Forwards
                                        M569 P8 S1			          								; physical drive 7 goes Forwards
                                        M569 P9 S1                                              	; physical drive 9 goes Forwards
                                        M584 X10 Y11 Z5:6:8:9 E3:4                              	; set drive mapping
                                        M671 X5.0:455.0:455.0:5.0 Y25.0:25.0:455.0:455.0 S14    	; ZBelts Near Locations                    
                                        M350 X16 Y16 Z16 E16:16 I1                              	; configure microstepping with interpolation
                                        M92 X80.00 Y80.00 Z410.00 E415.00:415.00 					; set steps per mm
                                        M566 X900.00 Y900.00 Z12.00 E120.00:120.00              	; set maximum instantaneous speed changes (mm/min)
                                        M203 X6000.00 Y6000.00 Z400 E1200.00:1200.00        		; set maximum speeds (mm/min)
                                        M201 X500.00 Y500.00 Z40.00 E250.00:250.00           		; set accelerations (mm/s^2)
                                        M906 X1800 Y1800 Z1000 E500.00:500.00 I30                     	; set motor currents (mA) and motor idle factor in per cent
                                        M84 S30                                                 	; Set idle timeout
                                        
                                        ; Axis Limits
                                        M208 X0 Y0 Z0 S1                                        	; set axis minima
                                        M208 X460 Y460 Z460 S0                                  	; set axis maxima
                                        
                                        M574 X1 S1 P"!xstop"                                    		; configure active-high endstop for low end on X via pin !xstop
                                        M574 Y1 S1 P"!ystop"                                    		; configure active-high endstop for low end on Y via pin !ystop
                                        
                                        M574 Z1 S2 														  ;   configure Z-probe endstop for low end on Z 
                                        M574 Z2 S1 P"!duex.e2stop+!duex.e3stop+!duex.e4stop+!duex.e5stop" ;   configure Z-probe endstop for low end on Z
                                        
                                        ; Z-Probe
                                        M558 P1 C"zprobe.in" H25 F600 T6000                      	; set Z probe type to unmodulated and the dive height + speeds
                                        G31 P500 X0 Y0 Z2.5                                     	; set Z probe trigger value, offset and trigger height
                                        M557 X20:440 Y20:440 S20                                	; define mesh grid
                                        
                                        
                                        ; Heaters
                                        M308 S0 P"bedtemp" Y"thermistor" T100000 B4725 C7.06e-8 	; configure sensor 0 as thermistor on pin bedtemp
                                        M950 H0 C"bedheat" T0                                   	; create bed heater output on bedheat and map it to sensor 0
                                        M307 H0 A11 C99000 D2000 B1                  				; enable bang-bang mode for the bed heater and set PWM limit
                                        M140 H0                                                 	; map heated bed to heater 0
                                        M143 H0 S120                                            	; set temperature limit for heater 0 to 120C
                                        M308 S1 P"spi.cs1" Y"thermocouple-max31856"             	; configure sensor 1 as thermocouple via CS pin spi.cs1
                                        M950 H1 C"e0heat" T1                                    	; create nozzle heater output on e0heat and map it to sensor 1
                                        M307 H1 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
                                        M308 S2 P"spi.cs2" Y"thermocouple-max31856"             	; configure sensor 2 as thermocouple via CS pin spi.cs2
                                        M950 H2 C"e1heat" T2                                    	; create nozzle heater output on e1heat and map it to sensor 2
                                        M307 H2 B0 S1.00                                        	; disable bang-bang mode for heater  and set PWM limit
                                        M308 S3 P"duex.e2temp" Y"thermistor" T10000 B3950       	; configure sensor 3 as thermistor on pin duex.e2temp
                                        M950 H3 C"duex.e2heat" T3                               	; create chamber heater output on duex.e2heat and map it to sensor 3
                                        M307 H3 A11 C99000 D2000 B1                             	; enable bang-bang mode for the chamber heater and set PWM limit
                                        M141 H3                                                 	; map chamber to heater 3
                                        
                                        ; Fans
                                        M950 F0 C"fan0" Q500                                    	; create fan 0 on pin fan0 and set its frequency
                                        M106 P0 S1 H-1                                          	; set fan 0 value. Thermostatic control is turned on                           
                                        M950 F1 C"fan1" Q500                                    	; create fan 1 on pin fan1 and set its frequency
                                        M106 P1 S1 H2 T45                                       	; set fan 1 value. Thermostatic control is turned on
                                        M950 F2 C"fan2" Q500                                    	; create fan 2 on pin fan2 and set its frequency
                                        M106 P2 S1 H1:2 T45                                     	; set fan 2 value. Thermostatic control is turned on
                                        
                                        ; Tools
                                        M563 P0 S"MAIN EXTRUDER" D0 H1 F0                       	; define tool 0
                                        G10 P0 X0 Y0 Z0                                         	; set tool 0 axis offsets
                                        G10 P0 R0 S0                                            	; set initial tool 0 active and standby temperatures to 0C
                                        M563 P1 S"SECOND EXTRUDER" D1 H2 F0                     	; define tool 1
                                        G10 P1 X0 Y0 Z0                                         	; set tool 1 axis offsets
                                        G10 P1 R0 S0                                            	; set initial tool 1 active and standby temperatures to 0C
                                        
                                        ; Custom settings are not defined
                                        
                                        ; Miscellaneous
                                        M575 P1 S1 B57600                                       	; enable support for PanelDue
                                        M501                                                    	; load saved parameters from non-volatile memory
                                        M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"      	; set voltage thresholds and actions to run on power loss
                                        T0                                                      	; select first tool
                                        
                                        
                                        

                                        Homeall.g


                                        ; homeall.g
                                        ; called to home all axes
                                        ;
                                        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:55 GMT-0500 (Central Daylight Time)
                                        G91                     ; relative positioning
                                        G1 H1 Z500 F6000          ; lift Z relative to current position
                                        G1 H1 X-465 F8000 ; move quickly to X endstop and stop there (first pass)
                                        G1 H1 Y-465 F8000 ; move quickly to Y endstop and stop there (first pass)
                                        G1 H2 X5 Y5 F6000       ; go back a few mm
                                        G1 H1 X-465 F360        ; move slowly to X axis endstop once more (second pass)
                                        G1 H1 Y-465 F360        ; then move slowly to Y axis endstop
                                        
                                        G1 X235 Y235 F6000      ; Prob at Center 
                                        M558 F600 A1 		    ; Dive fast once 
                                        G30			            ; probe Z
                                        M558 F300 A10 		    ; Slow second dive with more accuracy
                                        G30			            ; probe z again
                                        

                                        HomeZ.g


                                        ; homez.g
                                        ; called to home the Z axis
                                        ;
                                        ; generated by RepRapFirmware Configuration Tool v3.1.4 on Tue Oct 13 2020 21:14:56 GMT-0500 (Central Daylight Time)
                                        G91               ; relative positioning
                                        G1 H1 Z500 F6000    ; lift Z relative to current position
                                        G1 H1 Z-500 F3000 ; move Z down until the endstop is triggered
                                        G92 Z0            ; set Z position to axis minimum (you may want to adjust this)
                                        
                                        ; Uncomment the following lines to lift Z after probing
                                        ;G91              ; relative positioning
                                        ;G1 Z0 F100       ; lift Z relative to current position
                                        ;G90              ; absolute positioning
                                        
                                        

                                        M122

                                        M122

                                        === Diagnostics ===
                                        RepRapFirmware for Duet 2 WiFi/Ethernet version 3.3beta running on Duet Ethernet 1.02 or later + DueX5
                                        Board ID: 08DLM-996RU-N8PS0-7J9D8-3S86T-1B8VP
                                        Used output buffers: 6 of 24 (8 max)
                                        === RTOS ===
                                        Static ram: 23436
                                        Dynamic ram: 70168 of which 24 recycled
                                        Never used RAM 18452, free system stack 206 words
                                        Tasks: NETWORK(ready,263) HEAT(blocked,315) DUEX(blocked,29) MAIN(running,450) IDLE(ready,19)
                                        Owned mutexes:
                                        === Platform ===
                                        Last reset 00:01:11 ago, cause: power up
                                        Last software reset at 2021-02-04 13:09, reason: User, GCodes spinning, available RAM 18452, slot 2
                                        Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
                                        Error status: 0x00
                                        Aux0 errors 0,0,0
                                        MCU temperature: min 23.6, current 25.7, max 26.1
                                        Supply voltage: min 25.0, current 25.0, max 25.1, under voltage events: 0, over voltage events: 0, power good: yes
                                        Driver 0: position 0, standstill, SG min/max not available
                                        Driver 1: position 0, standstill, SG min/max not available
                                        Driver 2: position 0, standstill, SG min/max not available
                                        Driver 3: position 0, standstill, SG min/max not available
                                        Driver 4: position 0, standstill, SG min/max not available
                                        Driver 5: position 0, standstill, SG min/max not available
                                        Driver 6: position 0, standstill, SG min/max not available
                                        Driver 7: position 0, standstill, SG min/max not available
                                        Driver 8: position 0, standstill, SG min/max not available
                                        Driver 9: position 0, standstill, SG min/max not available
                                        Driver 10: position 0
                                        Driver 11: position 0
                                        Date/time: 2021-02-04 13:12:44
                                        Cache data hit count 110185932
                                        Slowest loop: 6.92ms; fastest: 0.21ms
                                        I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                        === Storage ===
                                        Free file entries: 10
                                        SD card 0 detected, interface speed: 20.0MBytes/sec
                                        SD card longest read time 3.8ms, write time 0.0ms, max retries 0
                                        === Move ===
                                        DMs created 83, maxWait 0ms, bed compensation in use: none, comp offset 0.000
                                        === MainDDARing ===
                                        Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                                        === AuxDDARing ===
                                        Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
                                        === Heat ===
                                        Bed heaters = 0 -1 -1 -1, chamberHeaters = 3 -1 -1 -1
                                        Heater 1 is on, I-accum = 0.0
                                        === GCodes ===
                                        Segments left: 0
                                        Movement lock held by null
                                        HTTP is idle in state(s) 0
                                        Telnet is idle in state(s) 0
                                        File is idle in state(s) 0
                                        USB is idle in state(s) 0
                                        Aux is idle in state(s) 0
                                        Trigger is idle in state(s) 0
                                        Queue is idle in state(s) 0
                                        LCD is idle in state(s) 0
                                        Daemon is idle in state(s) 0
                                        Autopause is idle in state(s) 0
                                        Code queue is empty.
                                        === DueX ===
                                        Read count 45, 37.91 reads/min
                                        === Network ===
                                        Slowest loop: 11.52ms; fastest: 0.02ms
                                        Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
                                        HTTP sessions: 1 of 8
                                        Interface state active, link 100Mbps full duplex
                                        
                                        

                                        M119

                                        2/4/2021, 1:14:39 PM	M119
                                        Endstops - X: not stopped, Y: not stopped, **Z: no endstop**, Z probe: not stopped
                                        
                                        

                                        Problems Key

                                        Driver 10 external servo Motor with an encoder on 3.3FR Not moving
                                        Endstop Still Same issue string Can't take more than 50 Characters.

                                        Thank You

                                        1 Reply Last reply Reply Quote 0
                                        • moe.adams9093undefined
                                          moe.adams9093
                                          last edited by

                                          Sorry forgot to post M98

                                          M98P"config.g"
                                          HTTP is enabled on port 80
                                          FTP is disabled
                                          TELNET is disabled
                                          Error: Unknown pin name 'duex.e5sto'
                                          Error: bad grid definition: Too many grid points; suggest increase spacing to 21.0mm
                                          Warning: Macro file config-override.g not found
                                          
                                          fcwiltundefined 1 Reply Last reply Reply Quote 0
                                          • fcwiltundefined
                                            fcwilt @moe.adams9093
                                            last edited by

                                            @moe-adams9093 said in G32 ERROR:

                                            Error: Unknown pin name 'duex.e5sto'

                                            It looks like that version of the firmware doesn't have the expanded command buffer - it's still dropping the last character.

                                            Frederick

                                            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA