Toolboard V1.0 error

tecno

@paulhew
M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 Mini 5+ FIRMWARE_VERSION: 3.2-beta3.2+1 ELECTRONICS: Duet 3 Mini5plus WiFi FIRMWARE_DATE: 2020-11-15

Still the same, downloaded 3rd time

tecno

M950 H1 C"121.out0" T1 changed to T0

So now thermistor is OK

Still no M303 for T0

PaulHew

@tecno No, until you get the updated firmware on the Mini.....

Reboot the board, either using e-stop or power off, wait 10 secs, then on again.

If M115 still reports the beta....

Use a different browser, Firefox maybe or Edge. Never trusted Chrome......

Download this, it is the same file that is on the Github
https://www.dropbox.com/s/csixik6j89bsaiq/Duet3Firmware_Mini5plus.uf2?dl=0

Using a browser other than Chrome, upload to the board using the 'Upload System Files' button.
Sorry, for teaching you to suck eggs, but after 3 years of running Duet boards, I have never had an issue!

Without the latter firmware the M303 will not work on a remote board.

tecno

@paulhew

OK, so FF did download the same as before
Your dropbox same same

There is somthing fischy going on. Maybe update via browser is not working OK?

jay_s_uk

@tecno IIRC, there was an issue updating the mini from 3.2beta3.2
You need to recover your board as described here https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Duet_3_Mini_5_WiFi_Ethernet

tecno

@jay_s_uk

Now next issues as the update via USB is OK

Homing Z not working = Z0 is way up and goes up for ever try setting Z0 evern higher.
No heater working on hotend

PaulHew

@tecno are there any messages in the console relating to heater issues?

As previously mentioned, I know nothing about your type of Z probe, I am afraid

tecno

@paulhew

Nothing else than the fault in picture.

I think rc42 is the man behind this probe. It did work connected directly to Mini 5 before.

Is there a way to check endstops if they are open or closed?

jay_s_uk

@tecno sounds like you need to flip the S value on M569 for the driver you've assigned to Z. Or you need to edit your homing files or endstop position.

And for the heater fault you probably need to PID tune your hotend.

PaulHew

m119 gives endstop status

tecno

@jay_s_uk

Sorry but M303 goes nowhere

tecno

@paulhew

Found it, sorry but I am so new to RepRap so all these commands are twisting myt head

m119
Endstops - X: not stopped, Y: not stopped, Z: at min stop, Z probe: at min stop

Above says that there is something wrong in config.

tecno

@jay_s_uk said in Toolboard V1.0 error:

@tecno sounds like you need to flip the S value on M569 for the driver you've assigned to Z. Or you need to edit your homing files or endstop position.

And for the heater fault you probably need to PID tune your hotend.

M564 and I can move Z as intended -25 goes down below 0

PaulHew

@tecno so hold one of the endstops and send the command again

tecno

@paulhew

X and Y are OK only Z is giving me problems.

PaulHew

@tecno what Z probe is it?
how many wires etc. Picture

tecno

@paulhew

https://www.duet3d.com/DuetAddons/IRProbe

PaulHew

@tecno Bit of RTFM required

With Duet 3 main board, expansion board or tool board: Connect the VCC, GND and OUT pins of the sensor to 3.3V, GND and IN respectively on an IO probe connector, and select mode 8 in the M558 command.

So pick a IO port such as IO_1, connect as above.

tecno

@paulhew

Got it workin with homeing. Did miss the correct port under endstops.

; Endstops
M574 X1 S1 P"!^121.io2.in" ; configure active-high endstop for low end on X via pin ^io3.in
M574 Y1 S1 P"!^io0.in" ; configure active-high endstop for low end on Y via pin ^io0.in
M574 Z1 S1 P"!!121.io1.in" ;

; Z-Probe
M558 P"!121.io1.in" X0 Y0 Z1 H3 F200 T5000 R0 ; P"!^io6.in"
M557 X15:400 Y15:400 S20 ; define mesh grid

Now to next Hotend Heater

tecno

Hotend tuning on its way now.