Toolboard V1.0 error

PaulHew

@tecno I have made a start for you. I know nothing about how an IR probe works, but you can use this as a template to work from.
config.json

Download the file
In the first page of the RRF config tool there is a 'Use existing configuration', select that and then select the above JSON file. and tweak to you hearts content.

tecno

@paulhew

Thanks Paul, appreciated.

tecno

M303 H1 S250
Error: M303: remote heater auto tune not implemented

Is it not possible to PID tune my hotend via Toolboard ?

How can I get going without PID?

Before I got CAN to work it show -273°C and now n/a

PaulHew

@tecno Config.g please......

Also M115 and a M115 B121

I suspect a bad connection on the temp. Have you wired it into temp0 on the toolboard?

Are you in the UK?

tecno

@paulhew

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out1" T0 ; create bed heater output on out1 and map it to sensor 0
M307 H0 R0.211 C620.5 D1.28 S1.00 V24.1 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C

M308 S1 P"121.temp1" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin temp1
M950 H1 C"121.out0" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B1 ; disable bang-bang mode for heater and set PWM limit B0 S1.00
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
M950 F0 C"121.out2" Q500 ; create fan 0 on pin out5 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out1" Q500 ; create fan 1 on pin out6 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"out3" Q500 ; create fan 2 on pin out3 and set its frequency
M106 P2 S1 H1 T45 ; set fan 2 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

m115
FIRMWARE_NAME: RepRapFirmware for Duet 3 Mini 5+ FIRMWARE_VERSION: 3.2-beta3.2+1 ELECTRONICS: Duet 3 Mini5plus WiFi FIRMWARE_DATE: 2020-11-15

M115 B121
Duet TOOL1LC firmware version 3.3RC2 (2021-05-11 14:59:50)

Will take a look on the thermistor

No this old fart is located s/w of Stockholm on the country side in Sweden

PaulHew

@tecno said in Toolboard V1.0 error:

FIRMWARE_NAME: RepRapFirmware for Duet 3 Mini 5+ FIRMWARE_VERSION: 3.2-beta3.2+1

Your Mini 5+ board has not been updated.
Delete the uf2 in system and upload again and when it asks if you want to update, click 'Yes' !!

Lets get that issue sorted 1st.

Then make sure your hotend temp probe is connected correctly to 'temp0'

tecno

@paulhew
M115
FIRMWARE_NAME: RepRapFirmware for Duet 3 Mini 5+ FIRMWARE_VERSION: 3.2-beta3.2+1 ELECTRONICS: Duet 3 Mini5plus WiFi FIRMWARE_DATE: 2020-11-15

Still the same, downloaded 3rd time

tecno

M950 H1 C"121.out0" T1 changed to T0

So now thermistor is OK

Still no M303 for T0

PaulHew

@tecno No, until you get the updated firmware on the Mini.....

Reboot the board, either using e-stop or power off, wait 10 secs, then on again.

If M115 still reports the beta....

Use a different browser, Firefox maybe or Edge. Never trusted Chrome......

Download this, it is the same file that is on the Github
https://www.dropbox.com/s/csixik6j89bsaiq/Duet3Firmware_Mini5plus.uf2?dl=0

Using a browser other than Chrome, upload to the board using the 'Upload System Files' button.
Sorry, for teaching you to suck eggs, but after 3 years of running Duet boards, I have never had an issue!

Without the latter firmware the M303 will not work on a remote board.

tecno

@paulhew

OK, so FF did download the same as before
Your dropbox same same

There is somthing fischy going on. Maybe update via browser is not working OK?

jay_s_uk

@tecno IIRC, there was an issue updating the mini from 3.2beta3.2
You need to recover your board as described here https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware#Section_Duet_3_Mini_5_WiFi_Ethernet

tecno

@jay_s_uk

Now next issues as the update via USB is OK

Homing Z not working = Z0 is way up and goes up for ever try setting Z0 evern higher.
No heater working on hotend

PaulHew

@tecno are there any messages in the console relating to heater issues?

As previously mentioned, I know nothing about your type of Z probe, I am afraid

tecno

@paulhew

Nothing else than the fault in picture.

I think rc42 is the man behind this probe. It did work connected directly to Mini 5 before.

Is there a way to check endstops if they are open or closed?

jay_s_uk

@tecno sounds like you need to flip the S value on M569 for the driver you've assigned to Z. Or you need to edit your homing files or endstop position.

And for the heater fault you probably need to PID tune your hotend.

PaulHew

m119 gives endstop status

tecno

@jay_s_uk

Sorry but M303 goes nowhere

tecno

@paulhew

Found it, sorry but I am so new to RepRap so all these commands are twisting myt head

m119
Endstops - X: not stopped, Y: not stopped, Z: at min stop, Z probe: at min stop

Above says that there is something wrong in config.

tecno

@jay_s_uk said in Toolboard V1.0 error:

@tecno sounds like you need to flip the S value on M569 for the driver you've assigned to Z. Or you need to edit your homing files or endstop position.

And for the heater fault you probably need to PID tune your hotend.

M564 and I can move Z as intended -25 goes down below 0

PaulHew

@tecno so hold one of the endstops and send the command again