Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Z setting ??

    Scheduled Pinned Locked Moved
    Config Tool
    3
    16
    588
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Robertoundefined
      Roberto
      last edited by

      Hello everyone,
      I have a problem with the tray adjustment. I changed the extrusion head and now the platen is too low in relation to the head. I do the all home, I get to 10mm, I go down 10mm, then I can go down another 0.5mm but when I want to go lower, it refuses.
      I changed the configuration but it doesn't change anything.
      Do you have a solution?
      Thank you.

      oliofundefined 1 Reply Last reply Reply Quote 0
      • oliofundefined
        oliof @Roberto
        last edited by

        @roberto how do you home Z? mechanical endstop or Z probe? If you use a mechanical endstop you'll need to adjust that. To move Z bezond Z=0 adjust M208 for the Z minimum; this of course only works when your movement system allows for that.

        <>RatRig V-Minion Fly Super5Pro RRF<> V-Core 3.1 IDEX k*****r <> RatRig V-Minion SKR 2 Marlin<>

        Robertoundefined 1 Reply Last reply Reply Quote 0
        • Robertoundefined
          Roberto @oliof
          last edited by

          @oliof Hello, I use a BL Touch

          oliofundefined 1 Reply Last reply Reply Quote 0
          • oliofundefined
            oliof @Roberto
            last edited by

            @roberto then you will need to readjust the z offset for your probe.

            <>RatRig V-Minion Fly Super5Pro RRF<> V-Core 3.1 IDEX k*****r <> RatRig V-Minion SKR 2 Marlin<>

            Robertoundefined 1 Reply Last reply Reply Quote 0
            • Robertoundefined
              Roberto @oliof
              last edited by

              @oliof I put M208. It refuses to go lower than Z-0.5mm. I don't understand why?

              Robertoundefined 1 Reply Last reply Reply Quote 0
              • Robertoundefined
                Roberto @Roberto
                last edited by

                @roberto I can't get the bed up near the nozzel

                oliofundefined 1 Reply Last reply Reply Quote 0
                • oliofundefined
                  oliof @Roberto
                  last edited by

                  @roberto Set Z minimum to -1 or -4 for adjustment. But be careful to not break your mechanics.

                  <>RatRig V-Minion Fly Super5Pro RRF<> V-Core 3.1 IDEX k*****r <> RatRig V-Minion SKR 2 Marlin<>

                  Robertoundefined 1 Reply Last reply Reply Quote 0
                  • Robertoundefined
                    Roberto @oliof
                    last edited by

                    @oliof Once I get to -0.5, the engines don't run anymore when I ask it to go to -1

                    Robertoundefined 1 Reply Last reply Reply Quote 0
                    • Robertoundefined
                      Roberto @Roberto
                      last edited by

                      @roberto Do I have to raise the plate manually?

                      oliofundefined 1 Reply Last reply Reply Quote 0
                      • oliofundefined
                        oliof @Roberto
                        last edited by

                        @roberto when you adjust the Z axis parameter, it should move via GCode, provided it's mechanically possible.

                        <>RatRig V-Minion Fly Super5Pro RRF<> V-Core 3.1 IDEX k*****r <> RatRig V-Minion SKR 2 Marlin<>

                        Robertoundefined 1 Reply Last reply Reply Quote 0
                        • Robertoundefined
                          Roberto @oliof
                          last edited by

                          @oliof I move the Z axis with the dashboard move command.
                          But, at Z-0.5mm, the motors don't respond anymore?
                          And the plate does not go up anymore. When I manually put the bed against the head, once I do the Z home, the bed goes back too far from the head. And even when I lower manually the tray voluntarily too much. I make the Zhome and again it comes to put itself with the same spacing with the head

                          Robertoundefined 1 Reply Last reply Reply Quote 0
                          • Robertoundefined
                            Roberto @Roberto
                            last edited by

                            @roberto he writes:
                            Error: Z probe already triggered at start of probing move Error: G0/G1 : insufficient axes homed

                            1 Reply Last reply Reply Quote 0
                            • Phaedruxundefined
                              Phaedrux Moderator
                              last edited by

                              Can you share your config.g and homeall.g and homez.g files as well as what firmware version you're using?

                              @oliof said in Z setting ??:

                              provided it's mechanically possible.

                              @Roberto Can the bed physically move higher or is it hitting an endstop or part of the frame preventing it from getting closer to the nozzle?

                              Z-Bot CoreXY Build | Thingiverse Profile

                              Robertoundefined 1 Reply Last reply Reply Quote 0
                              • Robertoundefined
                                Roberto @Phaedrux
                                last edited by

                                @phaedrux Hello,
                                I did some more tests.When I do the homes, I can't get it to go lower than -0.5. But with the baby stepping, I can get the tray up to the nozzel.
                                I go into the config and make the change.
                                Then when I do the homes, the plate goes back too low and again from -0.5 I can't make it go up.
                                Here are the settings.
                                I think that it is the BL-Touch that is out of adjustment.
                                How can I recalibrate the BL-Touch?
                                Thanks for the help.

                                SYSTEME.docx

                                Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator @Roberto
                                  last edited by

                                  @roberto said in Z setting ??:

                                  How can I recalibrate the BL-Touch?

                                  Yes it sounds like you need to re-measure your bltouch offset and or ensure it's mounted in the right height.

                                  https://duet3d.dozuki.com/Wiki/Test_and_calibrate_the_Z_probe

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  Robertoundefined 1 Reply Last reply Reply Quote 0
                                  • Robertoundefined
                                    Roberto @Phaedrux
                                    last edited by

                                    @phaedrux Ok! I will check the calibration of the BLTouch.
                                    Thanks for the info.

                                    1 Reply Last reply Reply Quote 0
                                    • First post
                                      Last post
                                    Unless otherwise noted, all forum content is licensed under CC-BY-SA