Updating to RRF 3.3

Rushmere3D

Hey all,

Looking to update to 3.3 for some features that would be useful for my E3D Toolchanger.

Can anyone tell me if there is anything config change wise I need to look out for with the update?

And as I run in SBC mode the update if via sudo commands is that correct?

Thanks.

Phaedrux

You don't mention which version you;re updating from, but you should check the release notes for all the versions in between yours and the one you're going to.

https://github.com/Duet3D/RepRapFirmware/wiki/Changelog-RRF-3.x#reprapfirmware-33

And yes, sudo apt update and sudo apt upgrade should get you up to date to 3.3 if you're on the stable channel.

Rushmere3D

@phaedrux

Coming from 3.2

I've had a look at the release notes but it just a wall of text and hard to understand.

Just want to know if there are any big gcode changes that will break something if I update.

dc42

@rushmere3d read at least the Upgrade Notes section for release 3.3. You can skip the new features and bug fixes lists.

Falkia

@rushmere3d You can make a new config with the configtool and compare it with your current config.

Rushmere3D

Hey all,

So I've gone ahead and updated, no issues so far.

But Settings-General still shows DWC as 3.2.2, do I need to update this manually?

Thanks.

Phaedrux

@rushmere3d said in Updating to RRF 3.3:

But Settings-General still shows DWC as 3.2.2, do I need to update this manually?

I suggest you update by uploading the full zip file to the system tab in DWC.

https://github.com/Duet3D/RepRapFirmware/releases/download/3.3/Duet2and3Firmware-3.3.zip

That should get everything up to date.

Rushmere3D

@phaedrux

This is ok to do when running in SBC mode right?

Can't I updated just the DWC with a .zip?

Thanks.

Phaedrux

No in that case ity should be getting updated with sudo apt update and Sudo apt upgrade.

Can you share the results of m122 please?

rjenkinsgb

@rushmere3d said in Updating to RRF 3.3:

But Settings-General still shows DWC as 3.2.2, do I need to update this manually?

It could just be your web browser cache - try hitting F5, if using Chrome, or control & page refresh.

Mine does not show a DWC update until I force a browser refresh.

Rushmere3D

@phaedrux

Sure, it's odd. As it appears as 3.2.2 first then a F5 shows 3.3.0 but then it doesn't stay as 3.3.0?

6HC

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v0.6 or 1.0 (SBC mode)
Board ID: 08DGM-9T66A-G63SJ-6J1D8-3SD6R-KV0BA
Used output buffers: 3 of 40 (14 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 63728 of which 0 recycled
Never used RAM 139560, free system stack 132 words
Tasks: SBC(ready,5.8%,310) HEAT(delaying,0.0%,325) Move(notifyWait,0.0%,279) CanReceiv(notifyWait,0.0%,799) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,7.3%,59) MAIN(running,86.7%,922) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:05:13 ago, cause: power up
Last software reset at 2022-01-23 13:15, reason: User, none spinning, available RAM 136716, slot 0
Software reset code 0x0012 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
Step timer max interval 188
MCU temperature: min 4.8, current 12.5, max 17.7
Supply voltage: min 23.9, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 10100, standstill, reads 42617, writes 28 timeouts 0, SG min/max 0/1023
Driver 1: position 19900, standstill, reads 42617, writes 28 timeouts 0, SG min/max 0/1023
Driver 2: position 4800, standstill, reads 42628, writes 17 timeouts 0, SG min/max 0/196
Driver 3: position 12250, standstill, reads 42633, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 42633, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 42619, writes 28 timeouts 0, SG min/max 0/993
Date/time: 2022-01-24 14:58:39
Slowest loop: 993.21ms; fastest: 0.04ms
=== Storage ===
Free file entries: 10
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 252509ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 20, completed moves 20, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger* is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 2743, received 3472, lost 0, longest wait 1ms for reply type 6042, peak Tx sync delay 53, free buffers 49 (min 48), ts 1570/1569/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
State: 4, failed transfers: 1, checksum errors: 0
Last transfer: 3ms ago
RX/TX seq numbers: 9476/9476
SPI underruns 0, overruns 0
Disconnects: 0, timeouts: 0, IAP RAM available 0x2c810
Buffer RX/TX: 0/0-0
=== Duet Control Server ===
Duet Control Server v3.3.0
Code buffer space: 4096
Configured SPI speed: 8000000Hz
Full transfers per second: 0.10, max wait times: 9.9ms/0.0ms
Codes per second: 0.00
Maximum length of RX/TX data transfers: 5332/984

3HC too.

M122 B1
Diagnostics for board 1:
Duet EXP3HC firmware version 3.3 (2021-06-15 16:12:41)
Bootloader ID: not available
Never used RAM 158696, free system stack 4400 words
Tasks: Move(notifyWait,0.0%,160) HEAT(delaying,0.0%,118) CanAsync(notifyWait,0.0%,69) CanRecv(notifyWait,0.0%,82) CanClock(notifyWait,0.0%,71) TMC(notifyWait,7.3%,63) MAIN(running,91.4%,334) IDLE(ready,0.0%,39) AIN(delaying,1.3%,263), total 100.0%
Last reset 00:07:45 ago, cause: software
Last software reset at 2021-08-16 15:20, reason: HardFault undefInstr imprec, available RAM 154848, slot 0
Software reset code 0x0060 HFSR 0x40000000 CFSR 0x00010400 ICSR 0x00000803 BFAR 0xe000ed38 SP 0x20003068 Task MAIN Freestk 386 ok
Stack: 00000000 00000000 2001cd90 00000f0d 00001f00 000249f5 00024a6a 21000000 000252fa 21000000 c4514360 49488282 0a1a0203 84e02041 50203502 ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff ffffffff
Driver 0: position 0, 409.0 steps/mm,  standstill, reads 26897, writes 16 timeouts 0, SG min/max 0/0, steps req 0 done 0
Driver 1: position 0, 80.0 steps/mm,  standstill, reads 26902, writes 11 timeouts 0, SG min/max 0/0, steps req 0 done 0
Driver 2: position 0, 80.0 steps/mm,  standstill, reads 26903, writes 11 timeouts 0, SG min/max 0/0, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter 0/15, peak Rx sync delay 180, resyncs 0/0, no step interrupt scheduled
VIN: 24.3V, V12: 12.2V
MCU temperature: min 9.4C, current 20.4C, max 20.4C
Ticks since heat task active 213, ADC conversions started 465710, completed 465710, timed out 0, errs 0
Last sensors broadcast 0x00000008 found 1 218 ticks ago, loop time 0
CAN messages queued 5321, send timeouts 0, received 4114, lost 0, free buffers 37, min 37, error reg 100000
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0

Rushmere3D

@rjenkinsgb

F5 fixes it until I reload the page from say a bookmark or close and open the browser.

jay_s_uk

@rushmere3d clear your cache then

Rushmere3D

@jay_s_uk

Yep, that's done it.

Updating to RRF 3.3

Robert J.