Strange Behavior , after "Pause" 'Cancel ""print again"

moth4017 · 7 Mar 2022, 08:01

 ; pause.g
; called when a print from SD card is paused
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Dec 30 2021 11:07:38 GMT+1300 (New Zealand Daylight Time)
M83            ; relative extruder moves
G1 E-10 F3600  ; retract 10mm of filament
G91            ; relative positioning
G1 Z5 F360     ; lift Z by 5mm
G90            ; absolute positioning
G1 X0 Y0 F6000 ; go to X=0 Y=0
 
; stop.g
; called when M0 (Stop) is run (e.g. when a print from SD card is cancelled)
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Dec 30 2021 11:07:38 GMT+1300 (New Zealand Daylight Time)
 
 
No Cancel.g 
 
Start script
M104 S[first_layer_temperature] ; set extruder temp
 
M109 S[first_layer_temperature] ; wait for extruder temp
 
G28 ; home all

OwenD · 7 Mar 2022, 09:24

@moth4017
I don't see anything out of the ordinary in those files.
Your M569 V parameter seems very low compared to the documentation, but I've never used that so I don't know enough to comment.

gloomyandy · 7 Mar 2022, 10:02

@moth4017 What current are you expecting the steppers to be set to? Your home z seems to leave it set to 600mA (which is significantly lower than the 1000mA initially set in config.g). You might want to try running M906 from the console before your initial print and then after you have hit pause and again after cancel to see what current is set at the various stages.

Not totally sure if it will help but you might also want to reconfigure the stall threshold to be higher after you have completed your homing just in case that is causing problems.

I notice that you also have M84 at the end of your zhome code, this is unusual. What are you expecting it to do?

moth4017 · 3 Jul 2022, 10:12

@gloomyandy
Hi i have also tried setting current to 1000ma still the same issue.

Ill try the M906 later
M84 is at the end of the home Z as i send the bed to Max Z and then turn off the motors ,

Phaedrux · 7 Mar 2022, 19:48

I think what's happening is that you're moving the Z axis to the max position and reducing the current. When it tries to move again it's stalling or maybe binding.

Return your motor current to normal before trying to move the axis again and see if it's able to move.

moth4017 · 8 Mar 2022, 04:02

@phaedrux
Hi when i do "pause print" "cancel" "print again" the bed has remained at the top position so it has not done the sensorless homing at Z max

Phaedrux · 8 Mar 2022, 18:09

@moth4017 said in Strange Behavior , after "Pause" 'Cancel ""print again":

No Cancel.g

Can you create a cancel.g file? Either put in some commands you want to happen when the print is canceled, or leave it blank for it to do nothing. The default cancel behaviour may be your problem.

https://docs.duet3d.com/en/User_manual/Reference/Gcodes#m0-stop-or-unconditional-stop

moth4017 · 9 Mar 2022, 06:22

@phaedrux

i should have done this before sorry

in the console when i press "print again"
i get these error messages
Error: Homing failed
Error: Driver 0.4 error: over temperature shutdown
Error: Driver 0.5 error: over temperature shutdown
Error: Driver 0.4 error: over temperature shutdown
Error: Driver 0.5 error: over temperature shutdown
Warning: Driver 0.4 warning: over temperature warning

gloomyandy · 9 Mar 2022, 08:31

@moth4017 Did you try running M906 so that you can see what current setting the drivers are using when they generate errors?

moth4017 · 9 Mar 2022, 08:49

@gloomyandy

M906 pre test X,y,Z 1000ma
after Cancel print
M906Motor current (mA) - X:1000, Y:1000, Z:1000, E:1400, idle factor 10%

gloomyandy · 9 Mar 2022, 09:03

@moth4017 Very odd? Do you always get those driver temperature errors when you have this problem?

moth4017 · 9 Mar 2022, 09:15

@gloomyandy
Hi Yes , but i can print ok if i send new G code , it only hppend after the above sequency

moth4017 · 3 Oct 2022, 19:42

@phaedrux
If i add the cancel.g file when pressing "cancel" button the cancel.g file does not run, cancel.g file in system directory

  
;cancel.g
M98 P/macros/home_max_Z
 
; home_max_Z
M400                                                ; make sure everything has stopped before we make changes
;G91                                 				; relative positioning
;;M915 P0.4:0.5:0.6 S3 F0 R0                          ; Configure Z-Axis Stall Detection
;M913 Z80                                     		; Lower motor current by 50%
;M574 Z2 S4                                       	; Configure Z-Axis stall detection homing
;G91  												; relative positioning
M98 P/macros/sensorless_Z      
G1 F3000											; 
G1 H1 Z350                           				; Home Z-Axis actuators independently
M400                                             	; make sure everything has stopped before we make changes
M913 Z100                                    		; Reset motor current
G90                                  				; absolute positioning
G92 Z290
 
;sensorless_z
M915 P0.4:0.5:0.6 S3 F0 R0                          ; Configure Z-Axis Stall Detection
M906 Z300	                                  		; Lower motor current by 50%
M574 Z2 S4                                       	; Configure Z-Axis stall detection homing
M400                                             	; make sure everything has stopped before we make changes
M906 Z1000	                                  		; Reset motor current
M400

Phaedrux · 10 Mar 2022, 21:45

Can you share the results of sending M122 and M98 P"config.g" ?

moth4017 · 10 Mar 2022, 22:01

@phaedrux ```
3/11/2022, 11:01:06 AM M122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.4.0rc2 (2022-02-22 17:07:31) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: 3R9YY-6T9RL-D65J0-40KMN-2UW2Z-RHYT0
Used output buffers: 3 of 40 (15 max)
=== RTOS ===
Static ram: 103652
Dynamic ram: 110396 of which 0 recycled
Never used RAM 27592, free system stack 132 words
Tasks: NETWORK(ready,49.2%,228) HEAT(notifyWait,0.1%,356) Move(notifyWait,0.0%,292) CanReceiv(notifyWait,0.0%,942) CanSender(notifyWait,0.0%,356) CanClock(delaying,0.0%,339) TMC(notifyWait,3.6%,114) MAIN(running,44.5%,428) IDLE(ready,0.0%,29) AIN(delaying,2.5%,264), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 02:17:44 ago, cause: power up
Last software reset at 2022-03-09 19:21, reason: User, GCodes spinning, available RAM 24040, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU revision 3, ADC conversions started 8264987, completed 8264987, timed out 0, errs 0
Step timer max interval 754
MCU temperature: min 28.5, current 30.2, max 32.7
Supply voltage: min 23.8, current 23.9, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: pos 0, standstill, SG min 0, read errors 0, write errors 0, ifcnt 9, reads 30414, writes 9, timeouts 0, DMA errors 0, CC errors 0
Driver 1: pos 0, standstill, SG min 0, read errors 0, write errors 0, ifcnt 9, reads 30414, writes 9, timeouts 0, DMA errors 0, CC errors 0
Driver 2: pos 96320, standstill, SG min 0, read errors 0, write errors 0, ifcnt 9, reads 30414, writes 9, timeouts 0, DMA errors 0, CC errors 0
Driver 3: pos 0, standstill, SG min 0, read errors 0, write errors 0, ifcnt 9, reads 30413, writes 9, timeouts 0, DMA errors 0, CC errors 0
Driver 4: pos 0, standstill, SG min 174, read errors 0, write errors 0, ifcnt 16, reads 30407, writes 16, timeouts 0, DMA errors 0, CC errors 0
Driver 5: pos 0, standstill, SG min 16, read errors 0, write errors 0, ifcnt 16, reads 30407, writes 16, timeouts 0, DMA errors 0, CC errors 0
Driver 6: pos 0, standstill, SG min 26, read errors 0, write errors 0, ifcnt 16, reads 30407, writes 16, timeouts 0, DMA errors 0, CC errors 0
Date/time: 2022-03-11 11:01:05
Cache data hit count 4294967295
Slowest loop: 5.52ms; fastest: 0.13ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 14.1ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 3, maxWait 624ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 2, completed 2, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 74382, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 18 (min 18), ts 41325/0/0
Tx timeouts 0,0,41324,0,0,33056 last cancelled message type 30 dest 127
=== Network ===
Slowest loop: 16.87ms; fastest: 0.00ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8

WiFi -
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.25
WiFi MAC address f0:08:d1:02:a1:0b
WiFi Vcc 3.34, reset reason Power up
WiFi flash size 2097152, free heap 25512
WiFi IP address 192.168.0.19
WiFi signal strength -49dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

moth4017 · 15 Mar 2022, 07:34

@phaedrux
hi any thourghts?

Phaedrux · 15 Mar 2022, 19:23

@moth4017 said in Strange Behavior , after "Pause" 'Cancel ""print again":

@phaedrux
If i add the cancel.g file when pressing "cancel" button the cancel.g file does not run, cancel.g file in system directory

  
;cancel.g
M98 P/macros/home_max_Z
 
; home_max_Z
M400                                                ; make sure everything has stopped before we make changes
;G91                                 				; relative positioning
;;M915 P0.4:0.5:0.6 S3 F0 R0                          ; Configure Z-Axis Stall Detection
;M913 Z80                                     		; Lower motor current by 50%
;M574 Z2 S4                                       	; Configure Z-Axis stall detection homing
;G91  												; relative positioning
M98 P/macros/sensorless_Z      
G1 F3000											; 
G1 H1 Z350                           				; Home Z-Axis actuators independently
M400                                             	; make sure everything has stopped before we make changes
M913 Z100                                    		; Reset motor current
G90                                  				; absolute positioning
G92 Z290
 
;sensorless_z
M915 P0.4:0.5:0.6 S3 F0 R0                          ; Configure Z-Axis Stall Detection
M906 Z300	                                  		; Lower motor current by 50%
M574 Z2 S4                                       	; Configure Z-Axis stall detection homing
M400                                             	; make sure everything has stopped before we make changes
M906 Z1000	                                  		; Reset motor current
M400

Can you try a simplified cancel.g? Maybe just a G28 XY

moth4017 · 16 Mar 2022, 06:58

@phaedrux

;cancel.g
G28 X Y

The console displayed this after cancel print:-
M0
Printing paused at X128.9 Y78.9 Z0.3
Cancelled printing file 0:/gcodes/shark-v2-0-a_0.35mm_PLA__2h32m.gcode, print time was 0h 5m

the Cancel.g file didnt run, so i put "G28 X Y" in the command line , this ran perfectly , but then i got this error in the console , only happens when i do the "Cancel"

3/16/2022, 7:56:33 PM Error: Driver 0.4 error: over temperature shutdown
3/16/2022, 7:56:33 PM Emergency stop, attemping to reconnect...
3/16/2022, 7:56:31 PM Error: Driver 0.6 error: over temperature shutdown
3/16/2022, 7:56:31 PM Error: Driver 0.5 error: over temperature shutdown
3/16/2022, 7:56:30 PM Error: Driver 0.4 error: over temperature shutdown

Phaedrux · 16 Mar 2022, 17:47

It seems like it's not picking up your files.

Can you get a fresh SD card out and set it up with fresh files entirely? Get a clean basic config from the config tool.

Maybe post some screen shots of your file structure? Or zip up your entire SD card minus the gcodes folder and post that?

moth4017 · 16 Mar 2022, 18:18

@phaedrux
Is there a reason it would not read the cancel.g only as if i change any macro files they are being read.

i will try i new install though

	; pause.g
	; called when a print from SD card is paused
	;
	; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Dec 30 2021 11:07:38 GMT+1300 (New Zealand Daylight Time)
	M83 ; relative extruder moves
	G1 E-10 F3600 ; retract 10mm of filament
	G91 ; relative positioning
	G1 Z5 F360 ; lift Z by 5mm
	G90 ; absolute positioning
	G1 X0 Y0 F6000 ; go to X=0 Y=0

	; stop.g
	; called when M0 (Stop) is run (e.g. when a print from SD card is cancelled)
	;
	; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Dec 30 2021 11:07:38 GMT+1300 (New Zealand Daylight Time)


	No Cancel.g

	Start script
	M104 S[first_layer_temperature] ; set extruder temp

	M109 S[first_layer_temperature] ; wait for extruder temp

	G28 ; home all


	;cancel.g
	M98 P/macros/home_max_Z

	; home_max_Z
	M400 ; make sure everything has stopped before we make changes
	;G91 ; relative positioning
	;;M915 P0.4:0.5:0.6 S3 F0 R0 ; Configure Z-Axis Stall Detection
	;M913 Z80 ; Lower motor current by 50%
	;M574 Z2 S4 ; Configure Z-Axis stall detection homing
	;G91 ; relative positioning
	M98 P/macros/sensorless_Z
	G1 F3000 ;
	G1 H1 Z350 ; Home Z-Axis actuators independently
	M400 ; make sure everything has stopped before we make changes
	M913 Z100 ; Reset motor current
	G90 ; absolute positioning
	G92 Z290

	;sensorless_z
	M915 P0.4:0.5:0.6 S3 F0 R0 ; Configure Z-Axis Stall Detection
	M906 Z300 ; Lower motor current by 50%
	M574 Z2 S4 ; Configure Z-Axis stall detection homing
	M400 ; make sure everything has stopped before we make changes
	M906 Z1000 ; Reset motor current
	M400