Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    I could use some help

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    11
    682
    64.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • A Former User?
      A Former User @fcwilt
      last edited by

      @fcwilt it’s at the back.

      fcwiltundefined 1 Reply Last reply Reply Quote 0
      • A Former User?
        A Former User @alankilian
        last edited by

        @alankilian sorry to disappear, texting on this iPhone 8’s a bitch. I’ll make that change and post a video of the results do you can see the results.

        1 Reply Last reply Reply Quote 0
        • fcwiltundefined
          fcwilt @A Former User
          last edited by

          @mac said in I could use some help:

          @fcwilt it’s at the back.

          So you have a moving bed.

          To get to the max end of Y the bed moves toward the front?

          To get to the min end of Y the bed moves toward the back?

          But stepping Y by minus 10 caused it to move toward the front?

          Frederick

          Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

          elmoretundefined A Former User? 2 Replies Last reply Reply Quote 0
          • elmoretundefined
            elmoret @fcwilt
            last edited by

            273 posts! 😮

            fcwiltundefined 1 Reply Last reply Reply Quote 0
            • fcwiltundefined
              fcwilt @elmoret
              last edited by

              @elmoret said in I could use some help:

              273 posts! 😮

              A lot I know. We will get mac sorted.

              Frederick

              Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

              1 Reply Last reply Reply Quote 0
              • A Former User?
                A Former User @fcwilt
                last edited by

                @fcwilt yes, that is what’s happening. The bed did touch the endstop and then back off; that’s an improvement.

                fcwiltundefined 1 Reply Last reply Reply Quote 0
                • fcwiltundefined
                  fcwilt @A Former User
                  last edited by

                  @mac said in I could use some help:

                  @fcwilt yes, that is what’s happening. The bed did touch the endstop and then back off; that’s an improvement.

                  Here's the problem.

                  When you tried jogging Y by -10 it went toward the front? Correct?

                  But the homing moves were supposed to be:

                  • a minus move
                  • a plus move
                  • a minus move

                  Based on the jogging test it should have moved:

                  • toward the front
                  • toward the back
                  • toward the front

                  I think there are two problems:

                  • the normal/reverse setting for the Y stepper is wrong (see M569 P0...)
                  • the steps per mm are wrong - too few (see M92)

                  I would like you to:

                  • change the M569 setting from whatever it is to the other setting
                  • try the home Y test and observe the movements
                  • try the jogging test and verify the correct directions
                  • if the directions are correct find some means to measure a move of, say, 100mm and see if a 100mm jog moves that distance.

                  Thanks.

                  Frederick

                  Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                  alankilianundefined 1 Reply Last reply Reply Quote 0
                  • alankilianundefined
                    alankilian @fcwilt
                    last edited by

                    @fcwilt said in I could use some help:

                    But the homing moves were supposed to be:

                    a minus move
                    a plus move
                    a minus move

                    Based on the jogging test it should have moved:

                    toward the front
                    toward the back
                    toward the front

                    Since it's a bed-slinger in Y, isn't a PLUS move going to move the bed towards the FRONT? (Move the head towards the +y part of the bed.)

                    I may be confused.

                    SeemeCNC Rostock Max V3 converted to V3.2 with a Duet2 Ethernet Firmware 3.2 and SE300

                    fcwiltundefined 1 Reply Last reply Reply Quote 0
                    • fcwiltundefined
                      fcwilt @alankilian
                      last edited by

                      @alankilian said in I could use some help:

                      @fcwilt said in I could use some help:

                      But the homing moves were supposed to be:

                      a minus move
                      a plus move
                      a minus move

                      Based on the jogging test it should have moved:

                      toward the front
                      toward the back
                      toward the front

                      Since it's a bed-slinger in Y, isn't a PLUS move going to move the bed towards the FRONT? (Move the head towards the +y part of the bed.)

                      I may be confused.

                      Correct (about the move, not about being confused). 😉

                      But according to mac a minus jogging move was moving the beds towards the front. I can only go by what he posts.

                      Frederick

                      Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                      A Former User? 1 Reply Last reply Reply Quote 0
                      • A Former User?
                        A Former User @fcwilt
                        last edited by

                        @fcwilt Y homes like it should. None of the + moves work. When I -10 it moves FORWARDS.

                        A Former User? fcwiltundefined 2 Replies Last reply Reply Quote 0
                        • A Former User?
                          A Former User @A Former User
                          last edited by

                          @mac

                          ; Configuration file for Duet 3 Mini 5+ (firmware version 3.3)
                          ; executed by the firmware on start-up
                          ;
                          ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
                          
                          ; General preferences
                          G90                                                ; send absolute coordinates...
                          M83                                                ; ...but relative extruder moves
                          M550 P"Frankenstein's Cinderella"                  ; set printer name
                          
                          ; Network
                          M552 S1                                            ; enable network
                          M586 P0 S1                                         ; enable HTTP
                          M586 P1 S0                                         ; disable FTP
                          M586 P2 S0                                         ; disable Telnet
                          
                          ; Drives
                          M569 P0.0 S1                                       ; physical drive 0.0 goes forwards
                          M569 P0.1 S1                                       ; physical drive 0.1 goes forwards
                          M569 P0.2 S1                                       ; physical drive 0.2 goes forwards
                          M569 P0.3 S1                                       ; physical drive 0.3 goes forwards
                          M584 X0.0 Y0.1 Z0.2 E0.3                           ; set drive mapping
                          M350 X16 Y16 Z16 E16 I1                            ; configure microstepping with interpolation
                          M92 X80.00 Y80.00 Z4000.00 E420.00                 ; set steps per mm
                          M566 X900.00 Y900.00 Z60.00 E120.00                ; set maximum instantaneous speed changes (mm/min)
                          M203 X6000.00 Y6000.00 Z600.00 E1200.00            ; set maximum speeds (mm/min)
                          M201 X500.00 Y500.00 Z200.00 E250.00               ; set accelerations (mm/s^2)
                          M906 X600 Y600 Z600 E600                           ; set motor currents (mA)
                          M84 S0                                             ; Disable motor idle current reduction
                          
                          ; Axis Limits
                          M208 X0 Y0 Z0 S1                                   ; set axis minima
                          M208 X220 Y220 Z240 S0                             ; set axis maxima
                          
                          ; Endstops
                          M574 X2 S1 P"!^io5.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on X via pin !^io5.in
                          M574 Y2 S1 P"!^io6.in"                             ; configure switch-type (e.g. microswitch) endstop for high end on Y via pin !^io6.in
                          
                          ; Z-Probe
                          M950 S0 C"io3.out"                                 ; create servo pin 0 for BLTouch
                          M558 P9 C"io3.in" H5 F120 T3600                    ; set Z probe type to bltouch and the dive height + speeds
                          G31 P500 X15.875 Y0.625 Z2.5                       ; set Z probe trigger value, offset and trigger height
                          M557 X5:190 Y5:215 S10                             ; define mesh grid
                          
                          ; Heaters
                          M308 S0 P"temp0" Y"thermistor" T100000 B4092       ; configure sensor 0 as thermistor on pin temp0
                          M950 H0 C"out0" T0                                 ; create bed heater output on out0 and map it to sensor 0
                          M307 H0 B0 S1.00                                   ; disable bang-bang mode for the bed heater and set PWM limit
                          M140 H0                                            ; map heated bed to heater 0
                          M143 H0 S33                                        ; set temperature limit for heater 0 to 33C
                          M308 S1 P"temp1" Y"thermistor" T100000 B4092       ; configure sensor 1 as thermistor on pin temp1
                          M950 H1 C"out1" T1                                 ; create nozzle heater output on out1 and map it to sensor 1
                          M307 H1 B0 S1.00                                   ; disable bang-bang mode for heater  and set PWM limit
                          M143 H1 S100                                       ; set temperature limit for heater 1 to 100C
                          
                          ; Fans
                          M950 F0 C"out3" Q500                               ; create fan 0 on pin out3 and set its frequency
                          M106 P0 S0 H-1                                     ; set fan 0 value. Thermostatic control is turned off
                          M950 F1 C"out4" Q500                               ; create fan 1 on pin out4 and set its frequency
                          M106 P1 S1 H1 T45                                  ; set fan 1 value. Thermostatic control is turned on
                          
                          ; Tools
                          M563 P0 S"optional" D0 H1 F0                       ; define tool 0
                          G10 P0 X0 Y0 Z0                                    ; set tool 0 axis offsets
                          G10 P0 R0 S0                                       ; set initial tool 0 active and standby temperatures to 0C
                          
                          ; Custom settings are not defined
                          
                          ; Miscellaneous
                          M501                                               ; load saved parameters from non-volatile memory
                          M911 S21 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
                          
                          
                          
                          A Former User? 1 Reply Last reply Reply Quote 0
                          • fcwiltundefined
                            fcwilt @A Former User
                            last edited by

                            @mac said in I could use some help:

                            @fcwilt Y homes like it should. None of the + moves work. When I -10 it moves FORWARDS.

                            I understand about the jogging move.

                            And since it is wrong you need to change normal to reverse or vice-versa in the M569 for the Y stepper.

                            That should get jogging going in the right direction.

                            IF it does try homing Y

                            Frederick

                            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                            1 Reply Last reply Reply Quote 0
                            • A Former User?
                              A Former User @A Former User
                              last edited by

                              @mac

                              ; homex.g
                              ; called to home the X axis
                              ;
                              ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
                              G91
                              G1 H1 X-230 F3600
                              G1 X15
                              G1 H1 X-10 F360
                               
                              G90
                              G1 X110 F3600 ; this just moves X to the centerline of the bed - doesn't matter where - it can be any place at all that suits you.
                              
                              
                              
                              
                              A Former User? 1 Reply Last reply Reply Quote 0
                              • A Former User?
                                A Former User @A Former User
                                last edited by

                                @mac

                                ; homey.g
                                ; called to home the Y axis
                                ;
                                ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
                                G91
                                G1 H1 Y-230 F3600
                                G1 Y15
                                G1 H1 Y-10 F360
                                 
                                G90
                                G1 Y110 F3600 ; this just moves Y to the centerline of the bed - doesn't matter where - it can be any place at all that suits you.
                                
                                
                                
                                
                                A Former User? 1 Reply Last reply Reply Quote 0
                                • A Former User?
                                  A Former User @A Former User
                                  last edited by

                                  This post is deleted!
                                  A Former User? fcwiltundefined 2 Replies Last reply Reply Quote 0
                                  • A Former User?
                                    A Former User @A Former User
                                    last edited by

                                    @mac

                                    ; homeall.g
                                    ; called to home all axes
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
                                    M98 P"homeZ.g"
                                    M98 P"homeX.g"
                                    M98 P"homeY.g"
                                    
                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91                  ; relative positioning
                                    ;G1 Z5 F60            ; lift Z relative to current position
                                    ;G90                  ; absolute positioning
                                    
                                    
                                    
                                    
                                    A Former User? 1 Reply Last reply Reply Quote 0
                                    • A Former User?
                                      A Former User @A Former User
                                      last edited by

                                      @mac That's where the code for my Duet3D Mini 5+ is today. Thank you to @droftarts , @fcwilt , and @alankilian for all their valuable contributions to this effort.

                                      A Former User? 1 Reply Last reply Reply Quote 0
                                      • A Former User?
                                        A Former User @A Former User
                                        last edited by

                                        @mac

                                        6/27/2022, 2:06:04 PM	G28 Z
                                        Error: Failed to enable endstops
                                        6/27/2022, 2:05:32 PM	Warning: Driver 0.0 warning: phase B may be disconnected
                                        6/27/2022, 2:05:32 PM	G28 X
                                        Warning: Driver 0.0 warning: phase B may be disconnected
                                        
                                        fcwiltundefined 1 Reply Last reply Reply Quote 0
                                        • fcwiltundefined
                                          fcwilt @A Former User
                                          last edited by fcwilt

                                          @mac said in I could use some help:

                                          @mac

                                          6/27/2022, 2:06:04 PM	G28 Z
                                          Error: Failed to enable endstops
                                          6/27/2022, 2:05:32 PM	Warning: Driver 0.0 warning: phase B may be disconnected
                                          6/27/2022, 2:05:32 PM	G28 X
                                          Warning: Driver 0.0 warning: phase B may be disconnected
                                          

                                          Well the warning about driver 0.0 would explain the noise and lack of proper movement.

                                          Frederick

                                          Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                          1 Reply Last reply Reply Quote 1
                                          • fcwiltundefined
                                            fcwilt @A Former User
                                            last edited by

                                            @mac said in I could use some help:

                                            @mac

                                            ; homez.g
                                            ; called to home the Z axis
                                            ;
                                            ; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Jun 27 2022 12:50:38 GMT-0700 (Pacific Daylight Time)
                                            G91               ; relative positioning
                                            G1 H2 Z5 F3600    ; lift Z relative to current position
                                            G1 H1 Z-245 F1800 ; move Z down until the endstop is triggered
                                            G92 Z0            ; set Z position to axis minimum (you may want to adjust this)
                                            
                                            ; Uncomment the following lines to lift Z after probing
                                            ;G91              ; relative positioning
                                            ;G1 Z5 F60        ; lift Z relative to current position
                                            ;G90              ; absolute positioning
                                            
                                            
                                            

                                            I don't get it, mac.

                                            I give you code to try and you end up with something rather different.

                                            I really do know what I am doing.

                                            Frederick

                                            Printers: a E3D MS/TC setup and a RatRig Hybrid. Using Duet 3 hardware running 3.4.6

                                            A Former User? 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA