ExecOnMcode

[Falcounet]

@CrazyCreator Can you give me a link to the system image you installed ?
I might give it a try on my pi.

[Falcounet]

@CrazyCreator TAMV is like 3 years old. I don't think python 3.9 was out at this time.

[stuartofmt]

Jumping in here with a (possibly) relevant comment. If anyone intends to use Pi cameras: Consider using Debian Bullseye as the min base OS. There is a new library (from Pi) in Bullseye - so adopting this release will provide some future-proofing. It does not directly affect USB cameras but likely not a bad idea.

[CrazyCreator]

@chrishamm said in ExecOnMcode v0.1:

@CrazyCreator Did you try the chown command I posted above? If that doesn't resolve it, try to run sudo rm /opt/dsf/**/ExecOnMcode* and then reinstall the plugin. It's odd you're getting that "access denied" error.

PS: The stock DuetPi image comes with the python 3 package, run sudo apt install python if you're missing it.

Yes ... try all your code-snippets ... now delete the directory and install the plugin again. but is the same error.

@Falcounet said in ExecOnMcode v0.1:

@CrazyCreator Can you give me a link to the system image you installed ?
I might give it a try on my pi.

is the official image which come with the raspianimagebuilder

@stuartofmt said in ExecOnMcode v0.1:

Jumping in here with a (possibly) relevant comment. If anyone intends to use Pi cameras: Consider using Debian Bullseye as the min base OS. There is a new library (from Pi) in Bullseye - so adopting this release will provide some future-proofing. It does not directly affect USB cameras but likely not a bad idea.

TAMV has a new version

Now i test the DuetPi Image with update to bullseye

[Falcounet]

@CrazyCreator So, I downloaded the image and following the steps I describe below, I could install the plugin without any issue.

1. Configure Wi-Fi and enable SSH in the advanced options of RaspberryPi Imager (Can be done by creating wpa_supplicant.conf and ssh files in boot partition)
2. Run sudo raspi-config and go to "Interface options", "SPI" to enable the SPI interface
3. Add Duet APT sources + GPG key : sudo wget -q https://pkg.duet3d.com/duet3d.gpg -O /etc/apt/trusted.gpg.d/duet3d.gpg && sudo wget -q https://pkg.duet3d.com/duet3d.list -O /etc/apt/sources.list.d/duet3d.list && sudo apt update
4. Install Duet packages + Apparmor: sudo apt install apparmor duetsoftwareframework duetpluginservice duetpimanagementplugin
5. Enable services : sudo systemctl enable duetcontrolserver duetwebserver duetpluginservice duetpluginservice-root
6. Reboot : sudo reboot
7. Install ExecOnMcode from DWC external plugins tab

[CrazyCreator]

@Falcounet
Which version did you load, 32bit or 64bit?

[Falcounet]

@CrazyCreator 32bits comes to default so I took that one

[CrazyCreator]

@Falcounet
what you think, should i try 64bit? make it a difference for the plugin? i think not?

[Falcounet]

@CrazyCreator I believe it will work the same but it is up to you. For the plugin itself, it won't make a difference.

[CrazyCreator]

@Falcounet
After your step 3 i have to make

sudo apt upgrade?

[Falcounet]

@CrazyCreator Actually I didn't added that but yes, upgrading system packages would be a good thing

[CrazyCreator]

@Falcounet
install is running now ... i have to wait

[CrazyCreator]

@Falcounet
Yeahhhh ... First Step is complete

Second Step

Now i need the synthax for sending this:

http://192.168.1.45/relay/0?turn=off and/or http://192.168.1.45/relay/0?turn=on

[CrazyCreator]

@Falcounet
You have a hint for me?

[Falcounet]

@CrazyCreator I think what you need is BtnCmd plugin but i'm not sure what you need exactly

[CrazyCreator]

@Falcounet
I would like to send an http command to my network when the printer has finished printing.
The command I wrote here turns off the smart socket and thus the printer.

I think is anything with curl or so ...

@BtnCmd: What is this and what can is do for me?

[Falcounet]

@CrazyCreator You can try adding a M1203 command doing curl http://192.168.1.45/relay/0?turn=off and then adding M1203 to your end-gcode.

[CrazyCreator]

@Falcounet said in ExecOnMcode v0.1:

curl http://192.168.1.45/relay/0?turn=off

[Falcounet]

@CrazyCreator The error comes from the relay you are trying to drive. I would suggest you to open a thread for your issue as it is not directly related to this plugin. Thanks
To add a bit more details, I think you have either to be identified or to allow an IP address from your network to send this command.

[CrazyCreator]

@Falcounet
maybe the switch need a password or so ... but in the old execonmcode script the same switch worked, without errors. i will see, maybe everyone have a idea what i can try.

thanks