It's out! RepRapFirmware 2.0 and 1.21.1 released

dc42

@knaudler said in It's out! RepRapFirmware 2.0 and 1.21.1 released:

@t3p3tony

hi
using fan 1 for hotend cooling
starting at 50 degrees - at 80% (have 15v input)

sometimes - if I want higher temps - 250 degrees - I push the fan to 90-100%
or if I need only 190 degrees - in the night, for extra silence - go down to 70% fan, thats ok

the only sound of the cr10 now are the fans

would be nice for me to controll all fans

thanks

One workaround would be to create a few macros to set different speeds for the hot end fan.

deckingman

@knaudler said in It's out! RepRapFirmware 2.0 and 1.21.1 released:

@t3p3tony

hi
using fan 1 for hotend cooling
starting at 50 degrees - at 80% (have 15v input)

sometimes - if I want higher temps - 250 degrees - I push the fan to 90-100%
or if I need only 190 degrees - in the night, for extra silence - go down to 70% fan, thats ok

the only sound of the cr10 now are the fans

would be nice for me to controll all fans

thanks

I don't know if you are aware of this but you can use thermostatic control to vary the fan speed over a range of temperatures which might achieve what you want automatically when you change the hot end temperature. This is what I do but in my case I just use zero speed below 60 deg C and full speed at 140 and above. In your case you could use for example M106 P1 S255 I0 F250 H1 T50:250 would give (if my maths is correct) zero speed at 50 degrees C and below, 70% speed at 190 deg C and 100% speed at 250 deg C. You might need to play around with those values and there is also an "L" parameter to set the minimum fan speed which you could use to give a non zero speed.

Knaudler

thats a good idea
I will test.

thanks

otaku521

is it just me... or if you have the web interface running on screen for a long time it is out of sync with the current status (I tell by looking at current z level location)

I had my big print on for a while and it tells me that I am at Z@ 11.xx but when I refresh the screen it is now changed to Z@17.xx

I never noticed that with the previous version

Thanks
Tony

SM3D

@otaku521 I too face the same problem - web interface shows a different value and I have to refresh the tab to see the current value.

In previous versions, it is either connected or disconnected. When it is connected, it is in sync with the actual print progress.

Cheers,
Vasan

dc42

I have once seen the web interface think it is connected when the printer was not turned on. I think this was after I woke up the PC from sleep mode, but I am not sure. I was using FireFox browser.

wilriker

@dc42 said in It's out! RepRapFirmware 2.0 and 1.21.1 released:

I have once seen the web interface think it is connected when the printer was not turned on. I think this was after I woke up the PC from sleep mode, but I am not sure. I was using FireFox browser.

I can see this more often then not when waking up my PC from sleep and not having manually disconnected DWC before sending the PC to sleep. I am using Vivaldi which basically is the same as Chrome.

zerspaner_gerd

@bmmal said in It's out! RepRapFirmware 2.0 and 1.21.1 released:

To expand further on my issue of not getting responses, it seems that DWC is somehow getting out of sync but not disconnecting ie ..........

@otaku521 @SM3D

I am glad that I am no longer the only one.

I have the same problem.

The debugging mode shows a difference:

DWC 1.21.1 stops after error:

0_1528647817320_debugging console 1.21.1.jpg

DWC 1.21 continues to run after error:

0_1528647176672_DWC 1.21 Debug.png

https://forum.duet3d.com/topic/5470/firmware-2-0rc6-and-1-21-1rc6-released/13

kraegar

Using it on the Railcore since released, non stop printing while I'm awake, and zero issues.

whosrdaddy

I confirm the issue @zerspaner_gerd is seeing, have sometimes the same problem.
Reloading the page resolves the problem.
I suspect this is a DWC bug...

whosrdaddy

@zerspaner_gerd : what is the value of the Ajax retries in your DWC settings?

zerspaner_gerd

@whosrdaddy
I tested at times until 4.
For a long time I stayed at 2, without change.

Am current back to 3 high, and this seems to show an improvement currently.

Did you observe the same?

Adamfilip

confused which files i need to use to upgrade to V2.0 for my duetwifi
lots of files listed

Duet2CombinedFirmware.bin
5.6 KB DuetDriverFiles.zip
356 KB DuetMaestroFirmware.bin
552 KB DuetWebControl-1.21.1.zip
290 KB DuetWiFiServer.bin
57.9 KB iap.bin
57.8 KB iap4e.bin
58 KB iap4s.bin
370 KB RepRapFirmware-Alligator.bin
292 KB RepRapFirmware-RADDS.bin
373 KB RepRapFirmware.bin
335 KB Symbols-CoreNG-SAM3X8E.zip
322 KB Symbols-CoreNG-SAM4E8E_RTOS.zip
305 KB Symbols-CoreNG-SAM4S_RTOS.zip
110 KB Symbols-FreeRTOS-SAM4E.zip
81.7 KB Symbols-FreeRTOS-SAM4S.zip
1.67 MB Symbols-RepRapFirmware-Duet085.zip
1.5 MB Symbols-RepRapFirmware-Duet2_RTOS.zip
1.48 MB Symbols-RepRapFirmware-DuetM_RTOS.zip
Source code (zip)
Source code (tar.gz)

Phaedrux

@adamfilip What firmware version are you upgrading from?

Duet2CombinedFirmware.bin should work. If you haven't upgraded in a while you may need to rename it. Check the firmware release notes for the interceding firmware.

dc42

@adamfilip said in It's out! RepRapFirmware 2.0 and 1.21.1 released:

confused which files i need to use to upgrade to V2.0 for my duetwifi

Which firmware version are you using at present?

Adamfilip

I tried the current Duet2CombinedFirmware.bin file and installed it. but this is what it says currently

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.0 or 1.01
Firmware Version: 1.21RC3 (2018-02-28 build 4)
WiFi Server Version: 1.21
Web Interface Version: 1.21.1

Phaedrux

@adamfilip Perhaps this will help? https://forum.duet3d.com/topic/5646/duet-wifi-not-updating-firmware-when-installing-2-0/2

FrankNPrinter

Hi Dave been a while.. I see things have really progressed since i pestered you last. LOL I am getting ready to upgrade so i can get wifi working again. Great to see the evolution and addition of ssid and pw btw! I see i have some firmware updates to do as well but it is all a little confusing. i was wondering if someone can give me a cliff notes version of what to do 1st.
Duet wifi running ver 1.18.1 with panel due v 1.15c PC and printer are in opposite ends of house so ideally do this via sd card? What do i do 1st? Also confused about which are the latest versions and where to get them. I am hoping to get my ducks in a row for this weekend . BTW, loved the tidbit from E3D on how great the duet is. I have another printer now, running mks 1.4 board and wow, it is a real dinosaur by comparison. I had no idea how lucky i was with my 1st system. I am currently building a system with 1540 mm X, and 1500 mm Y \ Z so looking forward to the Duet2 as well

Phaedrux

@franknprinter Take a good look through this document.

https://duet3d.dozuki.com/Wiki/Installing_and_Updating_Firmware

You'll need to follow the special steps for updating to 1.19 as things changed slightly at that point.

Adamfilip

@phaedrux

Thank you, yes this was my issue.