Smart effector first layer issues
-
I entered the values of the delta calibration in the config file, ran the macro and G29:
-
@Lakeman
that looks better notice your radius is some 8mm bigger
I would think about resetting your sensitivity back to default also
M672 S131:131 up to you but I've never seen any benefit to adjusting it with the stock bed
or of a config-override on a delta when you do a calibration before a print
Try a print ? fingers crossed ? -
I tried printing after this, no succes...
I will set the sensetivity back and try again -
@Lakeman
Where are you based in the world ? -
Germany
Failed again. The weird thing for me is that is is to close at one point, and to high 5mm further. It is so local that calibrition can hardly be a problem. Maybe I should go with an even finer mesh setting, but the original predator did not have a super fine mesh and had no problems at all....
-
Long shot...
Can you measure the carriage spacing and then effector spacing of the ball jointsor unclip the effector and line it up it to the carriage on all towers ?
-
If they are fine
Heat bed to 60c 130c hotend home then calibrate Z0.1 see if it goes to that position after calibration. -
@Carlo
Not my creation thanks to another user
macro name Prime nozzle also you can add to your start gcode for pla or change the temps for any filament S70 S220 in slicer
So home then delta calibrate first, then run the this macro
G90
M83
M207
T0
M116
G29 S1
M190 S70
M104 S220
M109 S220
; Draw arc to prime the nozzle between 6PM and 9PM on the bed edgeG1 X0 Y-175 Z0.25 F6000
G2 X-175 Y0 I0 J175 E30 F1500
G1 X-174.52
G3 X0 Y-174.52 I174.52 J0 E28 F1500
G1 Z1 E-0.25 F6000
-
Measured the spacing on the carriages and on the effector: Effector 64.6mm carriges 64.1mm
So there is room for improvement.. -
@Lakeman On my delta, I've always had issues with mesh calibration. I only use it to check the bed level, then turn it off for printing. When you're doing the delta calibration, is it turned off? Check there's an
M561andG29 S2at the beginning of bed.g (assuming that's where you delta calibration is), then if you do a mesh calibration afterwards, cancel it before trying to print.Ian
-
Did you change your belts? or tighten them as adjuster is touching the pulley plate so no more adjustment available mine have 15mm ish between them
-
It seems to be making the same mistake with or without mesh, I just tried a very fine mesh and without after with no succes
But maybe I have to fix the 0.5 mm in the spacing... -
@Lakeman
would be good to rule it out .5mm when your talking 0.12 -0.3mm layers? -
I think ruling it out is the best plan, just not entirely sure if it will work if I just scale the printed parts a bit and hopefully end up exactly 0.5mm wider
-
I am printing a 0.2mm first layer by the way and I do not know how much effect spacing between the balls has on the height,
-
have you got the link to the ones you printed as there are afew and I found these to be best
Used with the PCB ball mount supplied with the smart effector
anycubic_predator_carriage_SE-PCB_withoutFE.stl -
Link here for flying extruder version also
https://www.thingiverse.com/thing:356764
using the pcb supplied guarantees perfect spacing -
Haydn_Carriage_Adapter_Remix_v4.stl
This is what I used, I will try the stl file you send me, probebly the safest option to use the pcb's. Your second link goes to a tray, not sure what to do with that
-
Make sure that the spacing between each pair of towers is the same at the top, the bottom, and half way between top and bottom from duets website
The spacing between the bearings at the top of a pair of rods must be exactly the same as the spacing between the bearings at the bottom
-
get the linked version with the flying extruder mounting holes easier to mount the extruder
