Yet more conditional gcode help required

fma

Maybe something to do in daemon.g file? This way, you don't need to use trigger events, and you can poll all you want...

dc42

I think the best option may be to use a single trigger macro that responds to all 4 switches, that reads all 4 switches directly from the object model and makes appropriate movements, until none of the 4 switches is triggered.

deckingman

@fma said in Yet more conditional gcode help required:

Maybe something to do in daemon.g file? This way, you don't need to use trigger events, and you can poll all you want...

That's something I hadn't considered. But I'd need to restrict any movement to only happen when NOT printing. This will be possible using the R2 parameter in M581. Can the same thing be achieved with daemon.g?

deckingman

@dc42 said in Yet more conditional gcode help required:

I think the best option may be to use a single trigger macro that responds to all 4 switches, that reads all 4 switches directly from the object model and makes appropriate movements, until none of the 4 switches is triggered.

Ahh. That sounds a better option. I wasn't aware that a trigger could be initiated with any one of multiple pins. Can you point me to the command I'd need to use.

dc42

See https://duet3d.dozuki.com/Wiki/Gcode#Section_M581_RepRapFirmware_3_01RC2_and_later. The P parameter accepts multiple GpIn pin numbers.

deckingman

OK, I think I've sussed it but would appreciate a sanity check.

Config.g now has this......

M950 J5 C"^0.io5.in" ; main board(0) io5, joystick left 
M950 J6 C"^0.io6.in" ; main board(0) io6, joystick right
M950 J7 C"^0.io7.in" ; main board(0) io7, joystick forward 
M950 J8 C"^0.io8.in" ; main board(0) io8, joystick backwards
M581 P5:6:7:8 T5 R0 S0 ;Run trigger5 macro - (joystick left,right, forward or backwards)
; *** Note to self - change R0 to R2 after upgrading to firmware 3.2 **

.....and the macro looks like this.....

; ******Trigger 5 - Joystick left,right, forward or backwards ********
; IO Pin to switch connections J5=left, J6=Right, J7=Forward, J8=Backward


G91; Set relative
M400; wait for any moves to finish
G1 F6000 ; set feedrate to 100mm/sec
while sensors.gpIn[5].value=0 | sensors.gpIn[6].value=0 | sensors.gpIn[7].value=0 | sensors.gpIn[8].value=0
	if sensors.gpIn[5].value=0 ; joystick left
		G1 X-1 U-1 A-1
	elif sensors.gpIn[6].value=0 ; joystick right	
		G1 X1 U1 A1
	elif sensors.gpIn[7].value=0 ; joystick forwards	
		G1 Y-1 V-1 B-1
	elif sensors.gpIn[8].value=0 ; joystick backwards	
		G1 Y1 V1 B1
	elif sensors.gpIn[5].value=0 & sensors.gpIn[7]; joystick left and forward	
		G1 X-1 U-1 A-1 Y-1 V-1 B-1
	elif sensors.gpIn[5].value=0 & sensors.gpIn[8]; joystick left and backwards	
		G1 X-1 U-1 A-1 Y1 V1 B1
	elif sensors.gpIn[6].value=0 & sensors.gpIn[7]; joystick right and forward	
		G1 X1 U1 A1 Y-1 V-1 B-1
	elif sensors.gpIn[6].value=0 & sensors.gpIn[8]; joystick right and backward	
		G1 X1 U1 A1 Y1 V1 B1

I'm not sure about the "while". What I'm trying to say is while any one of those 4 pins is being pulled low by a switch do the following.

After that, I've used 8 "if" or "elif" statements to define what happens with the various switch combinations that are possible. Is that the way to do it?

OwenD

@deckingman You'll probably need to move the dual input directions in front of the uni-input directions.
Otherwise they won't execute using elif because each combination move will have previously equated to true in the single input section.

deckingman

@OwenD said in Yet more conditional gcode help required:

@deckingman You'll probably need to move the dual input directions in front of the uni-input directions.
Otherwise they won't execute using elif because each combination move will have previously equated to true in the single input section.

Ahh - good point. Does the rest of it look reasonable?

OwenD

@deckingman said in Yet more conditional gcode help required:

Ahh - good point. Does the rest of it look reasonable?

Looks reasonably sane.
You may need an M400 in each elif.
I'm not sure what the cycle time will be so you might experience an accumulation of moves by the time you take your hand off the joystick

deckingman

@OwenD said in Yet more conditional gcode help required:

@deckingman said in Yet more conditional gcode help required:

Ahh - good point. Does the rest of it look reasonable?

Looks reasonably sane.

That's unusual for me - I spend most of my time doing crazy stuff

You may need an M400 in each elif.

Good point - I'll plaster a few more M400s around

I'm not sure what the cycle time will be so you might experience an accumulation of moves by the time you take your hand off the joystick

Yes I had considered that - hence the 1mm "nudge move" length to start with. Guess I could either shorten that to (say) 0.1mm and/or scatter a few G4 commands around.

taconite

One suggestion: At the first 4 if statements I would add an "AND" with the negated statements of the last 4 if statements. Otherwise when you push the joystick to left forward the ifs "left", "forward" and "left forward" will be executed.

Or wait I think what I just read is only the case if using if instead of elif ...

dc42

That's the right approach, however the if..elif statements are not right. Try something like this:

    if sensors.gpIn[5].value=0           ; if left button down
        if sensors.gpIn[7].value=0       ; if joystick left and forward	
	    G1 ...
	elif sensors.gpIn[8].value=0     ; if joystick left and backwards	
	    G1 ...
        else                             ; just left
	    G1 ... 
    elif sensors.gpIn[6].value=0         ; right button down
	if sensors.gpIn[7].value=0       ; joystick right and forwards	
	    G1 ...
        elif sensors.gpIn[8].value=0     ; joystick right and backwards	
	    G1 ...
        else                             ; just right
	    G1 X1 U1 A1
    elif sensors.gpIn[7].value=0         ; if just forwards
	G1 ...
    elif sensors.gpIn[8].value=0         ; if just backwards
	G1 ...

You could also add an "else break" at the end, then you wouldn't need to test all the buttons in the while-part.

deckingman

@dc42 Thanks. That looks good. From my very limited knowledge, I can see that would be "conflict free" compared to what I had.

@all. Thanks for the input everyone - much appreciated. It'll be a couple of days or so before I get time to get the hardware and wiring sorted. Then I'll either report back with a successful outcome, or I'll be asking for more help........

OwenD

@dc42 said in Yet more conditional gcode help required:

That's the right approach, however the if..elif statements are not right. Try something like this:

You could also add an "else break" at the end, then you wouldn't need to test all the buttons in the while-part.

If he removes the while test of all pins, wouldn't the macro only trigger once (when a switch signal rose/fell)
Or do you just mean use "while true" instead (hence the break statement )
I'm always reluctant to use potentially infinite loops.

dc42

Yes I meant use "while true". Or if you don't like infinite loops, "while iterations < 1000" or similar.

OwenD

@dc42 Thanks for clarification.
I might have locked up a few machines over the years with my clumsy work when using loops.
I realise it's a valid method for those that think things through more than me before they press "executive" edit: "execute" (Stupid iPhone!!!)

deckingman

Err, in view of the above and as a further sanity check on my understanding, here is the full macro that I intend to start with ........

G91; Set relative
M400; wait for any moves to finish
G1 F6000 ; set feedrate to 100mm/sec

while sensors.gpIn[5].value=0 | sensors.gpIn[6].value=0 | sensors.gpIn[7].value=0 | sensors.gpIn[8].value=0
	
	if sensors.gpIn[5].value=0; joystick left 	
		
		if sensors.gpIn[7].value=0 ; joystick left and forwards 
			M400 
			G1 X-1 U-1 A-1 Y-1 V-1 B-1
			
		elif sensors.gpIn[8]; joystick left and backwards	
			M400
			G1 X-1 U-1 A-1 Y1 V1 B1
		
		else ; joystick left only
			M400
			G1 X-1 U-1 A-1
			
	elif sensors.gpIn[6].value=0; joystick right 	
		
		if sensors.gpIn[7].value=0 ; joystick right and forwards 
			M400
			G1 X1 U1 A1 Y-1 V-1 B-1
		
			
		elif sensors.gpIn[8]; joystick right and backward	
			M400
			G1 X1 U1 A1 Y1 V1 B1
			
		else ; joystick right only
			M400
			G1 X1 U1 A1
	
	elif sensors.gpIn[7].value=0 ; joystick forwards only	
		M400
		G1 Y-1 V-1 B-1
		
	elif sensors.gpIn[8].value=0 ; joystick backward only
		M400
		G1 Y1 V1 B1
		
	else break

Is that about right?

OwenD

To clarify my comments.

A "while" statement will loop if the condition test is true.
In your case by testing all those inputs.

If you put

while true
  G1 X1

Then you have an endless loop as true always equals true, so you're going to crash.
Therefore you must ensure that you put a test in somewhere the calls "break" to get you out of the loop.

In the suggested code above that test is satisfied when none of the IF statements resolve to true, so break is called.

deckingman

OK, so that's all wired up and working. It does what I hoped it would and it respects the axis limits too (of course it does - I never doubted it would ).

But I'd like to add an embellishment if possible. I've used 1mm as a movement length which is great for reasonably precise positioning but naturally, it's a bit slow if I want to travel the full 400mm or so of axis travel. Increasing the step size to (say) 5mm is about right but then I lose precision. So what I'd like to do is a bit like how one sets the time on some digital clocks. That is to say, the longer one holds the button, the faster the time changes.

So I'd like to alter the code so that if I hold the joystick in one position, it will move in 1mm increments but after (say) 5 iterations, the move length will increase to (say) 5mm). Ideally I'd like to do something a bit more sophisticated still, like keep increasing the move length the longer the joystick is held in one position but I'll settle for just a binary change after say 5 iterations of the same move.

Here is the code that I have now (without the errors that I had in some of the elif commands when I last posted it )

G91; Set relative
M400; wait for any moves to finish
G1 F6000 ; set feedrate to 100mm/sec
M118 S"Trigger 5 - Joystick"
while sensors.gpIn[5].value=0 | sensors.gpIn[6].value=0 | sensors.gpIn[7].value=0 | sensors.gpIn[8].value=0
	
	if sensors.gpIn[5].value=0; joystick left 	
		
		if sensors.gpIn[7].value=0 ; joystick left and forwards 
			M400 
			G1 X-1 U-1 A-1 Y-1 V-1 B-1
			echo "Left and forward"
			
		elif sensors.gpIn[8].value=0; joystick left and backwards	
			M400
			G1 X-1 U-1 A-1 Y1 V1 B1
			echo "Left and backwards"
			
		else ; joystick left only
			M400
			G1 X-1 U-1 A-1
			echo "Left"
			
	elif sensors.gpIn[6].value=0; joystick right 	
		
		if sensors.gpIn[7].value=0 ; joystick right and forwards 
			M400
			G1 X1 U1 A1 Y-1 V-1 B-1
			echo "Right and forward"
			
		elif sensors.gpIn[8].value=0; joystick right and backward	
			M400
			G1 X1 U1 A1 Y1 V1 B1
			echo "Right and backwards"
			
		else ; joystick right only
			M400
			G1 X1 U1 A1
			echo "Right"
	
	elif sensors.gpIn[7].value=0 ; joystick forwards only	
		M400
		G1 Y-1 V-1 B-1
		echo "Forward"
		
	elif sensors.gpIn[8].value=0 ; joystick backward only
		M400
		G1 Y1 V1 B1
		echo "Backwards"
		
	else break

dc42

You could use the built-in 'iterations' variable to adjust the movement amount and/or speed.