Tool board - no response

dutti

@phaedrux
After setting G4 S4 in front of the g.code --> same problem

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-956L2-G43S8-6J9D0-3S46R-9U2AD
Used output buffers: 3 of 40 (13 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92748 of which 100 recycled
Never used RAM 110440, free system stack 200 words
Tasks: NETWORK(ready,12.0%,212) ETHERNET(notifyWait,0.1%,124) HEAT(delaying,0.0%,331) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.1%,799) CanSender(notifyWait,0.0%,374) CanClock(delaying,0.0%,339) TMC(notifyWait,6.8%,93) MAIN(running,33.2%,1096) IDLE(ready,47.8%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:00:51 ago, cause: software
Last software reset at 2021-08-11 22:31, reason: User, GCodes spinning, available RAM 110464, slot 1
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0044a000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 127
MCU temperature: min 39.8, current 40.2, max 41.3
Supply voltage: min 24.0, current 24.0, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, reads 25598, writes 14 timeouts 0, SG min/max 0/0
Driver 1: position 0, standstill, reads 25598, writes 14 timeouts 0, SG min/max 0/0
Driver 2: position 0, standstill, reads 25598, writes 14 timeouts 0, SG min/max 0/0
Driver 3: position 0, standstill, reads 25599, writes 14 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 25599, writes 14 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 25599, writes 14 timeouts 0, SG min/max 0/0
Date/time: 2021-08-11 22:32:07
Slowest loop: 9.13ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 2.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== CAN ===
Messages queued 450, received 364, lost 67, longest wait 2ms for reply type 6049, peak Tx sync delay 6, free buffers 49 (min 48), ts 257/256/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 17.57ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8

Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0

; Configuration file for Duet 3 (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Mon Aug 02 2021 16:15:35 GMT+0200 (Mitteleuropäische Sommerzeit)

; General preferences
G90                                                        ; send absolute coordinates...
M83                                                        ; ...but relative extruder moves
M550 P"Duet 3"                                             ; set printer name

M552 S1 P192.168.2.108                                     ; Wifi
G4 S4

; Drives
M569 P0.0 S1                                               ; physical drive 0.0 goes forwards
M569 P0.1 S1                                               ; physical drive 0.1 goes forwards
M569 P0.2 S0                                               ; physical drive 0.2 goes forwards
M569 P0.3 S0                                               ; physical drive 0.2 goes forwards
M569 P0.4 S0                                               ; physical drive 0.2 goes forwards
M569 P0.5 S0                                               ; physical drive 0.2 goes forwards
M569 P121.0 S1                                             ; physical drive 121.0 goes forwards
M569 P122.0 S1                                             ; physical drive 122.0 goes forwards
M569 P123.0 S1                                             ; physical drive 123.0 goes forwards
M584 M584 X1.1 Y0.0:0.1 Z0.2:0.3:0.4:0.5 E121.0:122.0:123.0    ; set drive mapping
M350 X16 Y16 Z16 E16:16:16 I1                              ; configure microstepping with interpolation
M92 X160.00 Y160.00 Z640.00 E409.00:409.00:409.00          ; set steps per mm
M566 X900.00 Y900.00 Z60.00 E3000.00:3000.00:3000.00       ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z6000.00 E6000.00:6000.00:6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z300.00 E250.00:250.00:250.00         ; set accelerations (mm/s^2)
M906 X1300 Y1300 Z2500 E1000:1000:1000 I30                 ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                                    ; Set idle timeout

; Axis Limits
M208 X-10 Y-10 Z10 S1                                      ; set axis minima
M208 X1030 Y1030 Z1030 S0                                  ; set axis maxima

; Endstops
M574 X2 S1 P"^io3.in"                                      ; configure active-high endstop for high end on X via pin ^io3.in
M574 Y2 S1 P"^io1.in"                                      ; configure active-high endstop for high end on Y via pin ^io1.in
M574 Z1 S1 P"^io2.in"                                      ; configure active-high endstop for low end on Z via pin ^io2.in

; Z-Probe
M558 P0 H-5 F300 T300                                       ; disable Z probe but set dive height, probe speed and travel speed
M556 S50 X0 Y0 Z70                                         ; set orthogonal axis compensation parameters
M557 X10:10 Y10:10 S20                                     ; define mesh grid

; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B4138               ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0                                         ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 R0.243 C586.2 D33.87 S1.00 V0                ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0                                                    ; map heated bed to heater 0
M143 H0 S120                                               ; set temperature limit for heater 0 to 120C
M308 S1 P"121.temp0" Y"pt1000" R2200                       ; configure sensor 1 as PT1000 on pin 121.temp0
M950 H1 C"121.out0" T1                                     ; create nozzle heater output on 121.out0 and map it to sensor 1
M307 H1 B0 S1.00                                           ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S250                                               ; set temperature limit for heater 1 to 250C
M308 S2 P"122.temp0" Y"pt1000" R2200                       ; configure sensor 2 as PT1000 on pin 122.temp0
M950 H2 C"122.out0" T2                                     ; create nozzle heater output on 122.out0 and map it to sensor 2
M307 H2 B0 S1.00                                           ; disable bang-bang mode for heater  and set PWM limit
M143 H2 S250                                               ; set temperature limit for heater 2 to 250C
M308 S3 P"123.temp0" Y"pt1000" R2200                       ; configure sensor 3 as PT1000 on pin 123.temp0
M950 H3 C"123.out0" T3                                     ; create nozzle heater output on 123.out0 and map it to sensor 3
M307 H3 B0 S1.00                                           ; disable bang-bang mode for heater  and set PWM limit
M143 H3 S250                                               ; set temperature limit for heater 3 to 250C

; Fans
M950 F0 C"121.out1" Q500                                   ; create fan 0 on pin 121.out1 and set its frequency
M106 P0 S0 H-1                                             ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"121.out2" Q500                                   ; create fan 1 on pin 121.out2 and set its frequency
M106 P1 S1 H1 T45                                          ; set fan 1 value. Thermostatic control is turned on
M950 F2 C"122.out1" Q500                                   ; create fan 2 on pin 122.out1 and set its frequency
M106 P2 S1 H-1                                             ; set fan 2 value. Thermostatic control is turned off
M950 F3 C"122.out2" Q500                                   ; create fan 3 on pin 122.out2 and set its frequency
M106 P3 S1 H2 T45                                          ; set fan 3 value. Thermostatic control is turned on
M950 F4 C"123.out1" Q500                                   ; create fan 4 on pin 123.out1 and set its frequency
M106 P4 S1 H-1                                             ; set fan 4 value. Thermostatic control is turned off
M950 F5 C"123.out2" Q500                                   ; create fan 5 on pin 123.out2 and set its frequency
M106 P5 S1 H3 T45                                          ; set fan 5 value. Thermostatic control is turned on
M950 F6 C"out4" Q500                                       ; create fan 6 on pin out4 and set its frequency
M106 P6 S1 H-1                                             ; set fan 6 value. Thermostatic control is turned off
M950 F7 C"out5" Q500                                       ; create fan 7 on pin out5 and set its frequency
M106 P7 S1 H T45                                           ; set fan 7 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0                                           ; define tool 0
G10 P0 X30 Y28.25 Z45                                      ; set tool 0 axis offsets
G10 P0 R0 S0                                               ; set initial tool 0 active and standby temperatures to 0C
M563 P1 D1 H2 F2                                           ; define tool 1
G10 P1 X0 Y0 Z0                                            ; set tool 1 axis offsets
G10 P1 R0 S0                                               ; set initial tool 1 active and standby temperatures to 0C
M563 P2 D2 H3 F4                                           ; define tool 2
G10 P2 X0 Y0 Z0                                            ; set tool 2 axis offsets
G10 P2 R0 S0                                               ; set initial tool 2 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"         ; set voltage thresholds and actions to run on power loss

dutti

@barbarossa-cologne M122 B121
Diagnostics for board 121:
Duet TOOL1LC firmware version 3.3 (2021-06-15 16:12:58)
Bootloader ID: not available
Never used RAM 3636, free system stack 2789 words
Tasks: Move(notifyWait,0.0%,153) HEAT(delaying,0.1%,117) CanAsync(notifyWait,0.0%,65) CanRecv(notifyWait,0.0%,76) CanClock(notifyWait,0.0%,65) TMC(delaying,2.9%,57) MAIN(running,92.1%,350) IDLE(ready,0.0%,41) AIN(delaying,4.9%,142), total 100.0%
Last reset 00:03:41 ago, cause: software
Last software reset data not available
Driver 0: position 0, 409.0 steps/mm, standstill, SG min/max 0/0, read errors 0, write errors 1, ifcnt 61, reads 45026, writes 13, timeouts 0, DMA errors 0, steps req 0 done 0
Moves scheduled 0, completed 0, in progress 0, hiccups 0, step errors 0, maxPrep 0, maxOverdue 0, maxInc 0, mcErrs 0, gcmErrs 0
Peak sync jitter 0/9, peak Rx sync delay 208, resyncs 0/0, no step interrupt scheduled
VIN: 24.1V
MCU temperature: min 38.4C, current 38.5C, max 38.8C
Ticks since heat task active 186, ADC conversions started 220384, completed 220383, timed out 0, errs 0
Last sensors broadcast 0x00000002 found 1 191 ticks ago, loop time 0
CAN messages queued 2487, send timeouts 0, received 1957, lost 0, free buffers 37, min 37, error reg 0
dup 0, oos 0/0/0/0, bm 0, wbm 0, rxMotionDelay 0
Accelerometer detected: no
I2C bus errors 4619, naks 4619, other errors 4619

Phaedrux

Can you send m98 p"config.g" and post the results?

Do you have your other tool boards connected as well?

dutti

@phaedrux
I don´t have the other connected, yet.

Error: Response timeout: CAN addr 123, req type 6027, RID=96
Error: Fan number 5 not found
Error: in file macro line 82 column 13: M106: expected number after 'H'
11.8.2021, 22:44:22 Error: Response timeout: CAN addr 123, req type 6027, RID=94
Error: Fan number 4 not found
11.8.2021, 22:44:20 Error: Response timeout: CAN addr 122, req type 6027, RID=90
Error: Fan number 2 not found
Error: Response timeout: CAN addr 122, req type 6027, RID=92
Error: Fan number 3 not found
11.8.2021, 22:44:16 Error: Response timeout: CAN addr 123, req type 6026, RID=82
Error: Heater 3 not found
Error: Heater 3 does not exist
11.8.2021, 22:44:14 Error: Response timeout: CAN addr 122, req type 6043, RID=68
Response timeout: CAN addr 123, req type 6043, RID=69
Error: bad grid definition: X range too small
Error: Response timeout: CAN addr 122, req type 6031, RID=76
Error: Response timeout: CAN addr 122, req type 6026, RID=78
Error: Heater 2 not found
Error: Heater 2 does not exist
Error: Response timeout: CAN addr 123, req type 6031, RID=80
11.8.2021, 22:44:06 Error: Response timeout: CAN addr 122, req type 6042, RID=64
Response timeout: CAN addr 123, req type 6042, RID=65
11.8.2021, 22:44:04 Error: Response timeout: CAN addr 122, req type 6042, RID=60
Response timeout: CAN addr 123, req type 6042, RID=61
11.8.2021, 22:44:02 Error: Response timeout: CAN addr 122, req type 6042, RID=56
Response timeout: CAN addr 123, req type 6042, RID=57
11.8.2021, 22:44:00 Error: Response timeout: CAN addr 123, req type 6018, RID=53
Driver assignments: X1.1 Y0.0:0.1 Z0.2:0.3:0.4:0.5 E121.0:122.0:123.0, 3 axes visible
11.8.2021, 22:43:59 m98 p"config.g"
Error: Response timeout: CAN addr 122, req type 6018, RID=52

dutti

@barbarossa-cologne
Hot end fan is running.
Print cooling fan is not running.
I can´t control both.

Phaedrux

How is the PT1000 connected?
Is it actually a PT1000?

Photos of your toolboard wiring?

dutti

@phaedrux
It's the original tool changer thermistor.
Is it a pt100?
Oh no...

dutti

@phaedrux

dutti

@barbarossa-cologne

dc42

@barbarossa-cologne I've seen that crazy temperature value once before when a tool board was configured for a PT1000 sensor but the sensor wasn't connected.

dutti

@dc42 that's what I checked another time 2 minutes ago. It's definitely connected.

dc42

@barbarossa-cologne have you measured its resistance, to verify that it is a PT1000, not a PT100 or a thermistor?

dutti

@dc42 connected a different thermistor = same problem

dutti

@dc42
Yes. Now I connected a typical Chinese thermistor and it shows the same number for temperature:/

dc42

@barbarossa-cologne the config.g file you posted was for a PT1000, not a thermistor. Specifically, this line:

M308 S1 P"121.temp0" Y"pt1000" R2200 ; configure sensor 1 as PT1000 on pin 121.temp0

dutti

@dc42
Eeeehm ok.
Yes
That was the problem...
SOLVED
thanks a lot