Hi
I finally could get into my Duet Web Page, then I try to send home X and Y is doing fine, but when it move to Z the Bl Touch won't develop. I'm using Duet3 mini +5 and the Firmware 3.4.4 I also try 3.4.5 same thing.
I ran Yat and send code M997 S1 and it says Duetwifiserver Bin not found ???
Is there an specific version that I should use for Bl touch ????
I had to start from cero and accidently erase my folder from my sd card. I download the firmware use YAT, then connect my duet to my Wi-Fi, but won't open on my browser. it say Duet Wi-Fi server bin not found. I ran M20 p"/" and here is the results
m20 P"/"
Begin file list
System Volume Information
macros
Duet_RRF
Duet2and3Firmware-3.4.5 (1)
DuetWebControl-SD
config
config.zip
End file list
ok
Any help would much appreciated !! Thanks
How can unlock my account to have full access, I can't replay any of my question, Please help
Thanks for your help , I finally had the time to go back to the printer and check all the wires and YES there was a wire that was loose, so when the table moves to the corner it get disconnected, that's the reason stop working, I checked it many times I missed it.
Let see if now I can print at least the benchy 
@supertb1
thanks a lot your post help me to set my smart sensor. Appreciated
Hi All
I recently had to replaced a damaged belt and I checked my calibration with a test cube and I'm off .020 inches in my "Y" axis. how can adjust it on the system configuration ??
Thanks In advance
HI all
What is the maximum temperature I can reach with duet3 min. I can go up to 250 F ( hotend)but some filament require more. is there a setting I can manipulate to increase. I don't not much experience.
Thanks Much for your help !!
HI all
What is the maximum temperature I can reach with duet3 min. I can go up to 250 F but some filament require more. is there a setting I can manipulate to increase. I don't not much experience.
Thanks Much for your help !!
Thanks much for the replay I will watch the video. One more question, Is the m420 gcode working only with Marlin ??
Hi
I'm been struggle trying leveling my bed and can't get a good first layer. I have a v-core 500 and I'm using duet3 mini +5 . I run my thru bed leveling (g32) and seems like is not adjusting correctly. I don't know if a have a bad configuration. Here is mu config. my bed.g and homeall.g I hope you guys can help me because I don t know what else to do. this is not getting fun anymore.
code_text
**Bed.G**
```; this script compensates for what the Z offset is
; so if G31 P500 X-30 Y-15 Z1.7 then first probe will be at
; X30 Y20 (when G30 P0 X0 Y5)
M561 ; clear any bed transform
G30 P0 X25.40 Y25.40 F1000 Z-99999 ; probe near a leadscrew
G30 P1 X250 Y25.40 F1000 Z-99999 ; probe near a leadscrew
G30 P2 X440.00 Y25.40 Z-99999 ; probe near a leadscrew
G30 P3 X440.00 Y101.60 Z-99999 ; probe near a leadscrew
G30 P4 X250.00 Y101.60 Z-99999 ; probe near a leadscrew
G30 P5 X25.40 Y101.60 Z-99999 ; probe near a leadscrew
G30 P6 X25.40 Y220 Z-99999 ; probe near a leadscrew
G30 P7 X250 Y220 Z-99999 ; probe near a leadscrew
G30 P8 X440.00 Y220 Z-99999 ; probe near a leadscrew
G30 P9 X440.00 Y354.00 Z-99999 ; probe near a leadscrew
G30 P10 X250.00 Y354.00 Z-99999 ; probe near a leadscrew
G30 P11 X25.40 Y354.00 Z-99999 ; probe near a leadscrew
G30 P12 X25.40 Y480 Z-99999 ; probe near a leadscrew
G30 P13 X250 Y480 Z-99999 ; probe near a leadscrew
G30 P14 X440.00 Y480 Z-99999 S3 ; probe near a leadscrew
**Config.g**
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"V-Core3" ; set printer name
M669 K1 ; CoreXY
G21 ; Set Units to Millimeters
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0.0 S0 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes forwards
M569 P0.2 S0 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M569 P0.5 S0 ; physical drive 0.5 goes forwards
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E100.0 ; set steps per mm
M906 X1600 Y1600 Z1600 I30 ; set motor currents (mA) and motor idle factor in per cent -- safe for Duet 3 mini 5+
M84 S30 ; Set idle timeout
M566 X1000.00 Y1000.00 Z60.00 E3000.00 P1 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1000.00 E7200 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000 ; set accelerations (mm/s^2)
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X510 Y500 Z500 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"io0.in" ; configure active high endstops
M574 Y2 S1 P"io1.in" ; configure active high endstops
M564 H0
M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws
M557 X40:280 Y40:280 P5 ; define 5x5 mesh grid
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 Q11 ; create bed heater output on out5 and map it to sensor 0, lower switching frequency to 11Hz
M307 H1 R2.186 K0.17:0.11 D5.67 S1.00 V24.0 ; set the process parameters for heater 1
M307 H1 ; report model parameters for heater 1, and whether the model is being used
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
;; Run Bed PID Tune!! Below is an example for a 300x300 bed
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0
; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Layer Fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out3" Q500 ; create fan 1 on pin out3 and set its frequency
M106 P1 C"Hotend Fan" S1 H-1 T45 ; set fan 1 name and value. Thermostatic control turned on for Hotend
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250 ; set the maximum temperature in C for heater
; EVA 2 / BMG / E3D V6
M92 E1000.00 ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800 ; set extruder motor current (mA) and idle factor in per cent
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
;; Run Heater PID Tune!!
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0
; Z-Probe
;; Inductive Probe
; M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds
; G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
;; BLTouch
M950 S0 C"io2.out" ; Create a servo pin on io7
M558 P9 C"io2.in" H5 F240 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
G31 P25 X-28.00 Y-13.00 Z1.66 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
; Select default tool
; T0
; Pressure Advance
; M572 D0 S0.02
**Homeall.g**
M201 X500.00 Y500.00 ; Reduce acceleration for homing moves
; BLTouch
;M280 P0 S160 ; Precautionary alarm release
;M280 P0 S90 ; Ensure the pin is raised
G91 ; Relative positioning
G1 H2 Z5 F6000 ; Lift Z relative to current position
G1 H1 X-625 Y605 F4600 ; Move quickly to X and Y axis endstops and stop there (first pass)
G1 X3 Y-3 F600 ; Go back a few mm
G1 H1 X-625 Y605 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 X-625 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 Y605 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
M201 X3000 Y3000 ; Return to full acceleration
G90 ; Absolute positioning
G1 X250 Y250 F10000 ; Go to the center of the bed (300x300)
;G1 X200 Y200 F10000 ; Go to the center of the bed (400x400)
;G1 X250 Y250 F10000 ; Go to the center of the bed (500x500)
G30 ; Home Z by probing the bed
G91 ; Relative positioning
G1 Z5 F100 ; Lift Z relative to current position
G90 ; Absolute positioning
*here is my result from my heigh map*
Number of points: 25
Probe area: 575.8 cm²
Maximum deviations: -0.316 / -0.049 mm
Mean error: -0.169 mm
RMS error: 0.076 mm
I tried to upload a picture, but couldn't find the way to do it. Any help much be appreciated !!!Hi
I have a V-Core 500 I'm using duet3 mini WIFI with bltouch probe. Here is some information about my config
Homeall
code_text
```M201 X500.00 Y500.00 ; Reduce acceleration for homing moves
; BLTouch
;M280 P0 S160 ; Precautionary alarm release
;M280 P0 S90 ; Ensure the pin is raised
G91 ; Relative positioning
G1 H2 Z5 F6000 ; Lift Z relative to current position
G1 H1 X-625 Y605 F4600 ; Move quickly to X and Y axis endstops and stop there (first pass)
G1 X3 Y-3 F600 ; Go back a few mm
G1 H1 X-625 Y605 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 X-625 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
G1 H1 Y605 F1360 ; Move slowly to X and Y axis endstops once more (second pass)
M201 X3000 Y3000 ; Return to full acceleration
G90 ; Absolute positioning
G1 X250 Y250 F10000 ; Go to the center of the bed (300x300)
;G1 X200 Y200 F10000 ; Go to the center of the bed (400x400)
;G1 X250 Y250 F10000 ; Go to the center of the bed (500x500)
G30 ; Home Z by probing the bed
G91 ; Relative positioning
G1 Z5 F100 ; Lift Z relative to current position
G90 ; Absolute positioning
HomeZ```
; BLTouch
;M280 P0 S160 ; Precautionary alarm release
;M280 P0 S90 ; Ensure the pin is raised
G91 ; Relative positioning
G1 H2 Z5 F6000 ; Lift Z relative to current position
G90 ; Absolute positioning
G1 X250 Y250 F10000 ; Go to the center of the bed (300x300)
;G1 X200 Y200 F10000 ; Go to the center of the bed (400x400)
;G1 X250 Y250 F10000 ; Go to the center of the bed (500x500)
G30 ; Home Z by probing the bed
; Uncomment the following lines to lift Z after probing
;G91 ; Relative positioning
;G1 Z5 F100 ; Lift Z relative to current position
;G90 ; Absolute positioning
Thanks
@Deez3443 ```
code_text
; This is a system-generated file - do not edit
; Heater model parameters
M307 H0 R0.130 K0.150:0.000 D10.00 E1.35 S1.00 B1
M307 H1 R2.430 K0.560:0.000 D5.50 E1.35 S1.00 B0 V0.0
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00
here is my config. overrideHI All
I can't figure out what to do, every time I turn the printer on my Z offset change. I did follow the duet instruction how to adjust the z offset and change it on my config g. what do I'm missing ??
Any help will be appreciated.
Here is my config.g
; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"V-Core3" ; set printer name
M669 K1 ; CoreXY
G21 ; Set Units to Millimeters
; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0.0 S0 ; physical drive 0.0 goes forwards
M569 P0.1 S0 ; physical drive 0.1 goes forwards
M569 P0.2 S0 ; physical drive 0.2 goes forwards
M569 P0.3 S1 ; physical drive 0.3 goes forwards
M569 P0.4 S1 ; physical drive 0.4 goes forwards
M569 P0.5 S0 ; physical drive 0.5 goes forwards
M584 X0.4 Y0.3 Z0.0:0.1:0.2 E0.5 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E100.0 ; set steps per mm
M906 X1600 Y1600 Z1600 I30 ; set motor currents (mA) and motor idle factor in per cent -- safe for Duet 3 mini 5+
M84 S30 ; Set idle timeout
M566 X1000.00 Y1000.00 Z60.00 E3000.00 P1 ; set maximum instantaneous speed changes (mm/min)
M203 X18000.00 Y18000.00 Z1000.00 E7200 ; set maximum speeds (mm/min)
M201 X3000.00 Y3000.00 Z100.00 E10000 ; set accelerations (mm/s^2)
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X510 Y500 Z500 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"io0.in" ; configure active high endstops
M574 Y2 S1 P"io1.in" ; configure active high endstops
M564 H0
M671 X-4.5:250:504.5 Y-4.52:505:-4.52 S5 ; define positions of Z leadscrews or bed levelling screws
M557 X30:280 Y30:280 P5 ; define 5x5 mesh grid
; Heaters
M308 S0 P"temp0" Y"thermistor" T100000 B3950 A"Bed" ; configure sensor 0 as thermistor on pin temp0
M950 H0 C"out0" T0 Q11 ; create bed heater output on out5 and map it to sensor 0, lower switching frequency to 11Hz
M307 H1 R2.186 K0.17:0.11 D5.67 S1.00 V24.0 ; set the process parameters for heater 1
M307 H1 ; report model parameters for heater 1, and whether the model is being used
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
;; Run Bed PID Tune!! Below is an example for a 300x300 bed
;; M307 H0 A303.1 C356.7 D1.4 S1.00 V24.0 B0
; Fans
M950 F0 C"out4" Q500 ; create fan 0 on pin out4 and set its frequency
M106 P0 C"Layer Fan" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned off
M950 F1 C"out3" Q500 ; create fan 1 on pin out3 and set its frequency
M106 P1 C"Hotend Fan" S1 H-1 T45 ; set fan 1 name and value. Thermostatic control turned on for Hotend
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
M950 H1 C"out1" T1 ; create nozzle heater output on out2 and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S250 ; set the maximum temperature in C for heater
; EVA 2 / BMG / E3D V6
M92 E1000.00 ; set extruder steps per mm, 0.9 angle/step (LDO Pancake)
M906 E800 ; set extruder motor current (mA) and idle factor in per cent
M308 S1 P"temp1" Y"thermistor" T100000 B4725 C7.060000e-8 A"Hotend"
;; Run Heater PID Tune!!
;; M307 H1 A751.5 C196.6 D4.7 S1.00 V23.9 B0
; Z-Probe
;; Inductive Probe
; M558 P5 C"!io3.in" H5 F400 T5000 ; set Z probe type to unmodulated and the dive height + speeds
; G31 P500 X-30 Y-15 Z0.20 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
;; BLTouch
M950 S0 C"io2.out" ; Create a servo pin on io7
M558 P9 C"io2.in" H5 F240 T10800 A5 ; set Z probe type to unmodulated and the dive height + speeds
G31 P25 X-28.00 Y-13.00 Z1.12 ; set Z probe trigger value, offset and trigger height, more Z means closer to the bed
; Select default tool
T0
; Pressure Advance
; M572 D0 S0.02
Hi
here is the model of my modem !!!
BGW320-505
Thanks
code_text
```7/2/2023, 3:25:15 AM Connection established
7/2/2023, 3:25:15 AM Connection interrupted, attempting to reconnect...
Network error
7/2/2023, 3:23:31 AM Connection established
7/2/2023, 3:23:31 AM Connection interrupted, attempting to reconnect...
Network error
7/2/2023, 3:23:23 AM Connection established
7/2/2023, 3:23:23 AM Connection interrupted, attempting to reconnect...
Network error
7/2/2023, 3:21:23 AM m122
=== Diagnostics ===
RepRapFirmware for Duet 3 Mini 5+ version 3.4.5 (2022-11-30 19:41:16) running on Duet 3 Mini5plus WiFi (standalone mode)
Board ID: 5PQ93-S296U-D65J0-40KMG-1A03Z-7DGLP
Used output buffers: 1 of 40 (33 max)
=== RTOS ===
Static ram: 103652
Dynamic ram: 110472 of which 60 recycled
Never used RAM 23808, free system stack 118 words
Tasks: NETWORK(notifyWait,15.1%,197) HEAT(notifyWait,0.0%,320) Move(notifyWait,0.4%,265) CanReceiv(notifyWait,0.0%,942) CanSender(notifyWait,0.0%,326) CanClock(delaying,0.0%,333) TMC(notifyWait,1.2%,72) MAIN(running,82.1%,417) IDLE(ready,0.2%,30) AIN(delaying,0.9%,263), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 10:21:58 ago, cause: power up
Last software reset at 2023-07-01 05:38, reason: User, GCodes spinning, available RAM 27360, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
MCU revision 3, ADC conversions started 37320849, completed 37320848, timed out 0, errs 0
Step timer max interval 1479
MCU temperature: min 44.2, current 50.1, max 50.6
Supply voltage: min 26.9, current 27.1, max 27.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 99/0, heap memory allocated/used/recyclable 2048/496/496, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min 0, read errors 0, write errors 0, ifcnt 36, reads 40096, writes 5, timeouts 0, DMA errors 0, CC errors 0
Driver 1: standstill, SG min 0, read errors 0, write errors 0, ifcnt 36, reads 40096, writes 5, timeouts 0, DMA errors 0, CC errors 0
Driver 2: standstill, SG min 0, read errors 0, write errors 0, ifcnt 36, reads 40097, writes 5, timeouts 0, DMA errors 0, CC errors 0
Driver 3: standstill, SG min 0, read errors 0, write errors 0, ifcnt 30, reads 40099, writes 2, timeouts 0, DMA errors 0, CC errors 0
Driver 4: standstill, SG min 0, read errors 0, write errors 0, ifcnt 30, reads 40099, writes 2, timeouts 0, DMA errors 0, CC errors 0
Driver 5: standstill, SG min 0, read errors 0, write errors 0, ifcnt 22, reads 40099, writes 2, timeouts 0, DMA errors 0, CC errors 0
Driver 6: standstill, SG min 0, read errors 0, write errors 0, ifcnt 9, reads 40101, writes 0, timeouts 0, DMA errors 0, CC errors 0
Date/time: 2023-07-02 03:21:22
Cache data hit count 4294967295
Slowest loop: 787.14ms; fastest: 0.08ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 22.5MBytes/sec
SD card longest read time 5.8ms, write time 111.0ms, max retries 0
=== Move ===
DMs created 83, segments created 36, maxWait 202027ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 567, completed 567, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 9], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 3971, received 0, lost 0, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 0, free buffers 18 (min 18), ts 2206/0/0
Tx timeouts 0,0,2206,0,0,1765 last cancelled message type 4514 dest 127
=== Network ===
Slowest loop: 532.25ms; fastest: 0.06ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Network state is active
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 4
WiFi firmware version 1.27
WiFi MAC address d8:bf:c0:14:e8:37
WiFi Vcc 3.38, reset reason Power up
WiFi flash size 2097152, free heap 23424
WiFi IP address 192.168.1.118
WiFi signal strength -41dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0
7/2/2023, 3:21:09 AM M0
Cancelled printing file 0:/gcodes/First layer calibration_0.3mm_PLA_3m.gcode, print time was 0h 2m
7/2/2023, 3:21:08 AM M25
Resume state saved
Warning: Macro file pause.g not found
Printing paused at X28.3 Y42.0 Z0.2