@ droftarts
tnx i will take a look, i have cura 4.9 (as it seams last to work on Win7)
@fcwilt im not too superstitious just yet maybe after few more failed 24h bulds
@ droftarts
tnx i will take a look, i have cura 4.9 (as it seams last to work on Win7)
@fcwilt im not too superstitious just yet maybe after few more failed 24h bulds
@phaedrux
ok i got everything updated
thank you for helping!
now time to start connecting everything
@jay_s_uk
im surprised it does not exist :((
i guess i can write my own plugin if i reverse how shaping plugin works
@jay_s_uk
will try to see if i use that as base point
if my idea works would be nice to use duet for my lasers
@jay_s_uk
will try to see if i use that as base point
if my idea works would be nice to use duet for my lasers
@jay_s_uk
im surprised it does not exist :((
i guess i can write my own plugin if i reverse how shaping plugin works
@alexus
i guess something worked
question is there way to use acceleromenter to determine maximum acceleration, jerk, backlash for hardware... so ex we push motion form reasonable to super fats to see expected vs config acceleration plus see when things start to jump
@jay_s_uk
oh. lets to update again i wish they can be done automatically :(((
EDIT: ok updated to RC3 and it magically detects (well at least not complains about nothing on port)
tnx for help... now time to figure out how to use plugin )))) much more fun then doing taxes
Hi i just got official duet3d accelerometer board 1.0 connected to temp header expansion with provided cable
used this line in config and i get message that accelerometer not found of specified port
M955 P0 C"spi.cs2+spi.cs1"
i have Duex connected, i tried toccevting to its port too (updating SPI CS[] lines of course but nothing changes... treds all possible variations but no luck
defective accelerometer? wrong cable (though lines are strait)
im running Duet Web Control 3.5.0-rc.1
Any way to debug this?
EDIT: also strange behavior... when connected accelerometer i no longer can open control web page on my desktop, looks like CSS does not load so page is useles, however!! i can open page on laptop just fine.. they both on wifi, including duet. When dsconecting accelerometer desctop can connect to duet just fine too... also green light on accelerometer lights up so orientation/ polarity is correct. i amuse this is spi noise but why it affects one device and not other (it should just affect ESP chip and both computers should see same problem)
@jens55
monkeys eat apples, seams logical
tehre is no termocouple in the list of options, should i use linear-analog?
@MJLew
i can try ur gcode just to see how it print , but as i see features are not added any wehere so far?
also what i noticed with my models, cylindrical is ok when i used prusa slicer but 2 tower with hole in it still seams terrible
hi
i got this sensor but it gives me trouble (wanted to use it for heat bed)
https://www.amazon.com/WRNT‑02-K-Type-Thermocouple-Temperature-Measuring/dp/B09BZGXYWF
i measured resistance looks like 10 Ohm when i use that for config it shows 30C +/- which seamed ok room temp 24C but fine... i tried to heat up bed and temp did not change
any ideas? or just give up and get PT1000 or something
M308 S1 P"bedtemp" Y"thermistor" T8 B4138 ; configure sensor 1 as for heatbed
M950 H1 C"bedheat" T1 ; create bed heater output on bedheat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H1 ; map heated bed to heater 1
M143 H1 S120 ; set temperature limit for heater 1 to 120C
@alexus
so did thin wall test and looks like my walls are 0.4mm on 0.4mm nozle seams good to me
though i switched to prusa slicer for that test and i printed 2 models
one (other design) got printed defets free , perfect part , while same part foprm cura never been perfect... then i printed my part with 2 prone towers and while it printed significantly better it still showed similar artifact perhaps tuning prisa slicer can make it better... failr note i did change material and i put material in drying/preheat chamber
@droftarts
in thta case i can use my cheap china caliper lol i dont think its well relibale