ok i got everything updated
thank you for helping!
now time to start connecting everything
so updated file w/ extruder speed ... things got better yet there are still some artifact... i will read about tuning flow and and back to this... probably will finish my current job 1st as i need 10000 of peaces in any quality :)))
i did not tube retraction speed, i guess need to go throuhdocument and see how to do it
will try to increase speed and accesration parameters
in CURA retraction speed is hidden i guess? i did not see it in list but will double check again... lets play around when current print is done
tnx for helping
here is G config, also i did calibrate E0 to extract exact amount as expected ex 100mm gets me 100mm on cold filment. i will go through link to see if i missed anything
for filament diameter its 1.7 measured, and i think cura setting was 1.83 something (will double check)
here is link to print file https://we.tl/t-6Ir4qixkiK
it was 1mb so loaded to we transfer
; Configuration file for Duet WiFi (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.2.3 on Tue Jun 08 2021 21:52:22 GMT-0400 (Eastern Daylight Time) ; General preferences G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Duet2Wifi" ; set printer name ; Network M552 S1 ; enable network M586 P0 S1 ; enable HTTP M586 P1 S0 ; disable FTP M586 P2 S0 ; disable Telnet ; Drives M569 P0 S1 ; physical drive 0 goes forwards X M569 P1 S1 ; physical drive 1 goes forwards Y M569 P2 S0 ; physical drive 2 goes forwards Z M569 P3 S1 ; physical drive 3 goes forwards M584 X0 Y1 Z10 E3 ; set drive mapping (Alexus backup: X0 Y1 Z2 E3) M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X80.00 Y44.44 Z320 E800 ; set steps per mm (Alexus 6.28.21 - fine tuned alredy - do not edit) M566 X800.00 Y800.00 Z100.00 E120.00 ; set maximum instantaneous speed changes (mm/min) M203 X6000.00 Y6000.00 Z800.00 E1200.00 ; set maximum speeds (mm/min) M201 X800.00 Y800.00 Z100.00 E250.00 ; set accelerations (mm/s^2) M906 X800 Y1200 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Axis Limits M208 X0 Y0 Z0 S1 ; set axis minima M208 X500 Y500 Z300 S0 ; set axis maxima ; Endstops M574 X1 S1 P"!xstop" ; configure active-high endstop for low end on X via pin xstop M574 Y1 S1 P"!ystop" ; configure active-high endstop for low end on Y via pin ystop M574 Z1 S1 P"!zstop" ; configure active-high endstop for low end on Z via pin zstop ;M574 Z1 S2 ; Config to use Prbe as Z Limit (Alexus) ; Z-Probe ;Alexus BL Touch Declarations M558 P9 C"^zprobe.in" H5 F100 T2000 ; Type 9 BL Touc, w/ pull up, H5 is dive heght 5mm M950 S0 C"exp.heater3" ; heater 3 epension port - pin 8 yellow wire for servo deploy PWM G31 X28.78 Y0 Z2.25 P25 ; Probe Offest ; END declarations M557 X150:350 Y150:350 S20 ; define mesh grid ; Heaters M140 H-1 ; disable heated bed (overrides default heater mapping) M308 S0 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin e0temp M950 H0 C"e0heat" T0 ; create nozzle heater output on e0heat and map it to sensor 0 M307 H0 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit M143 H0 S280 ; set temperature limit for heater 0 to 280C ; Fans M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off ; Tools M563 P0 D0 H0 F-1 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ; Custom settings are not defined ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M501 ; load saved parameters from non-volatile memory
well i guess flow of extrusion was my other question and i cold not find where to sent flow any where so i was controlling it with slider to set it 300% as at 100% i was not getting enough material to hold model layers. Never the less i not really think its hole burned is flow related as i think if i some hor reduce amount of delay to 0 then there will be no heating and melting of a crater at seam
so just finished my build and when i prrint parts i see at the end of later and seam spot nozzle stops for about 1 sec before moving up makes makes a crater. I think it might be related to retract time .. my retract is 6.5mm but if i reduce thhat i get spider web. is there any way to remove that behaviour? im comparing to makerbot and i dont see that on maker bot... actually my seam likes quite bad comparing to makerbot (tried different setting) also good to mention bowen line is long but i think its not related as nozzle is ironing spot with heat /delay
any idea? its this cura related or machine settings?
help is appreciated
yep i figured that... right now wil leave 50mm to be safe
for now i think im set for z axis... though i had to use ratio to calculate mm/step instead of figuring out mechanical exected values so i might have some deviation... but any way lets get XY axis working lol
thank you for your help!