I received a new fuse and replaced it, and the fan is now working.
Thank you very much for your help.

@Phaedrux 　Thank you very much.
I had misunderstood the phase wiring.
I connected it correctly again using a multimeter and jumper wires and was able to get all the motors running.
It looks like there is probably no damage to the motor drivers.

@droftarts @phaedrux Thank you for your kind remarks to my ignorance.
I finished setting up the M671 today. The result on Bed.g looks like this.
Bed image:
G32Results：G32
Manual corrections required: 0.00 turn up (0.00mm) 0.19 turn down (0.09mm) 0.13 turn down (0.07mm) 0.19 turn down (0.10mm)
Thank you for telling us.
I don't think I could have done so much with my knowledge.

@phaedrux 　Thank you for your reply.
I now understand the relationship between X and Y. Thank you.

@droftarts 　Thank you for your reply.

@droftarts said in The height map is not created correctly:

Is the probe in front or behind the nozzle? To the left or the right?

The nozzle is in front of the printer. And the probe is set at 20mm in front from the nozzle.

@droftarts　Thank you for your reply.
This picture is taken from the back of the printer.
Y is about -20 places from the maximum
X is about two thirds of the way from the minimum.
In the printer settings, this is the maximum position.
In order to improve the serviceability of the printer, the bed can be moved up to 500mm

@droftarts Sorry for the delay in replying.
Thank you for your reply.
I have reworked the parts you pointed out.

I rewrote homeall.g and it looks like this.

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.5 on Sun Nov 14 2021 09:23:55 GMT+0900 (日本標準時)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-305 Y-305 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-305 Y-305 F360  ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-305 F360        ; move Z down stopping at the endstop
G90                     ; absolute positioning
G1 X150 Y150 Z5 F2000 ; put head over the centre of the bed, or wherever you want to probe
G30 ; lower head, stop when probe triggered and set Z to trigger height


;G92 Z0                  ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

As a result, when HomeAll is done, after the X and Y axis hit the limit switch, the carriage moves to the centre and is now Z-probed.

The next question is about the probe offset.
This is a CAD simulation of my probe.


You will probably need to enter X+20 or X-20 as the offset for G31.
I have checked the offset and if I move the probe to where the hot end nozzle is marked, then at +20mm the probe will be in the same position as the nozzle.
I set it to X20 on the G31.
However, I don't think that the Y axis offset is moving from the nozzle to either side. In this case, is it correct to set the Y offset to 0?

The next question is about Using the Manual Bed Levelling Assistant.
The prerequisite for Using the Manual Bed Levelling Assistant is
｛You need to use the {M671 command to define the X and Y coordinates of the adjusting screw. The M671 command must be specified after the M667 or M669 command in config.g}.
but the adjustment screw on my printer bed is on the inside of the bed.
Is this something I should be concerned about?
Also, there is no M669 in my Config.g. What should I do in this case?

@phaedrux Thank you for your reply.

@phaedrux said in The height map is not created correctly:

Do you actually use bed.g? Or call it with G32 at any point?

I ran G32 and found that P1 and P4 were not probed as the probes were sticking out of the bed.

@phaedrux said in The height map is not created correctly:

homeall.gファイルとhomez.gファイルを投稿できますか？

This is Homeall

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.3.5 on Sun Nov 14 2021 09:23:55 GMT+0900 (日本標準時)
G91                     ; relative positioning
G1 H2 Z5 F6000          ; lift Z relative to current position
G1 H1 X-305 Y-305 F1800 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000       ; go back a few mm
G1 H1 X-305 Y-305 F360  ; move slowly to X and Y axis endstops once more (second pass)
G1 H1 Z-305 F360        ; move Z down stopping at the endstop
G90                     ; absolute positioning
G92 Z0                  ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91                    ; relative positioning
;G1 Z5 F100             ; lift Z relative to current position
;G90                    ; absolute positioning

This is Homez

; homez.g
; called to home the Z axis
;
; generated by RepRapFirmware Configuration Tool v3.3.5 on Sun Nov 14 2021 09:23:56 GMT+0900 (日本標準時)
G91 ; relative mode
G1 S2 Z5 F200 ; raise head 4mm to ensure it is above the Z probe trigger height
G90 ; back to absolute mode
G1 X150 Y150 F2000 ; put head over the centre of the bed, or wherever you want to probe
G30 ; lower head, stop when probe triggered and set Z to trigger height

;G91               ; relative positioning
;G1 H2 Z5 F6000    ; lift Z relative to current position
;G1 H1 Z-305 F1800 ; move Z down until the endstop is triggered
;G92 Z0            ; set Z position to axis minimum (you may want to adjust this)

; Uncomment the following lines to lift Z after probing
;G91              ; relative positioning
;G1 Z5 F100       ; lift Z relative to current position
;G90              ; absolute positioning

@phaedrux said in The height map is not created correctly:

When the heightmap has such a large offset it's usually because the mesh has been created without the z axis being homed with the probe first.

Now I understand why the height map was made so low.

@phaedrux said in The height map is not created correctly:

Your homing files should home the Z axis with the probe using G30 at the center of the bed to set the Z0 location. Then create a fresh height map.

Does this mean that I need to do a paper filler test in the centre of the bet and then run 「G92 Z0」 and then 「G29」?

@droftarts Thank you for your reply.
In my printer, the X axis is currently the axis that moves the bed.

As @droftarts pointed out, there is a possibility that the large FAN attached to the hot end has a negative effect, so I removed the FAN and measured again.
Here is the resulting image.

Here are the results after adjusting the height again.

@phaedrux 　Thank you for your reply.
The shape is very similar to my Prusa printer, so it is a Cartesian type.
Photo:
The printer's bed is usually used with a black paper between a glass plate and an aluminium plate.
photo：
The sensor used is an IR probe.
Photo:
Here is the probe I bought
URL：IRSensor
Finally, here is the Bed.g file.

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v3.3.5 on Sun Nov 14 2021 09:23:54 GMT+0900 (日本標準時)
M561 ; clear any existing bed transform
M401 ; deploy Z probe if necessary
G30 P0 X60 Y30 Z-99999 ; define 4 points in a clockwise direction around the bed, starting near (0,0)
G30 P1 X330 Y30 Z-99999
G30 P2 X330 Y290 Z-99999
G30 P3 X60 Y290 Z-99999 
G30 P4 X150 Y150 Z-99999 S0 ; finally probe bed centre, and calculate compensation
M402 ; retract the Z probe
G1 X0 Y0 F5000 ; move the head to the corner (optional)

;M561 ; clear any existing bed transform
;M401 ; deploy Z probe if necessary
;G30 P0 X10 Y10 Z-99999 ; define 4 points in a clockwise direction around the bed, starting near (0,0)
;G30 P1 X10 Y190 Z-99999
;G30 P2 X190 Y190 Z-99999
;G30 P3 X190 Y10 Z-99999
;G30 P4 X100 Y100 Z-99999 S0 ; finally probe bed centre, and calculate compensation
;M402 ; retract the Z probe
;G1 X0 Y0 F5000 ; move the head to the corner (optional)

;M561 ; clear any bed transform
;G29  ; probe the bed and enable compensation

@droftarts said in The height map is not created correctly:

config.g

Thank you for your patience.
Here is my config.g.

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.5 on Fri Nov 05 2021 01:14:08 GMT+0900 (日本標準時)

; General preferences
M575 P1 S1 B57600                              ; enable support for PanelDue
G90                                            ; send absolute coordinates...
M83                                            ; ...but relative extruder moves
M550 P"kotuo02"                                ; set printer name

; Network
M551 P"kotuo"                                  ; set password
M552 S1                                        ; enable network
M586 P0 S1                                     ; enable HTTP
M586 P1 S0                                     ; disable FTP
M586 P2 S0                                     ; disable Telnet

; Drives
M569 P0 S1                                     ; physical drive 0 goes forwards
M569 P1 S1                                     ; physical drive 1 goes backwards
M569 P2 S0                                     ; physical drive 2 goes backwards
M569 P3 S1                                     ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                               ; set drive mapping
M350 X16 Y16 Z16 E16 I1                        ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z4000.00 E369.00             ; set steps per mm
M566 X600.00 Y600.00 Z60.00 E300.00            ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E6000.00        ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E500.00           ; set accelerations (mm/s^2)
M906 X600 Y600 Z600 E600 I30                   ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                        ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1                               ; set axis minima
M208 X330 Y300 Z300 S0                         ; set axis maxima

; Endstops
M574 X1 S1 P"xstop"                            ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop"                            ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S1 P"zstop"                            ; configure switch-type (e.g. microswitch) endstop for low end on Z via pin zstop

; Z-Probe
M558 P1 C"zprobe.in" H5 F120 T6000             ; set Z probe type to unmodulated and the dive height + speeds
;M558 H30                                      ;*** Remove this line after delta calibration has been done and new delta parameters have been saved
G31 P500 X20 Y0 Z3.272                    ; set Z probe trigger value, offset and trigger height
M557 X80:330 Y20:280 S60     			   ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B1 S1.00                               ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0                                        ; map heated bed to heater 0
M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00                               ; disable bang-bang mode for heater  and set PWM limit
M143 H1 S260                                   ; set temperature limit for heater 1 to 260C

; Fans
M950 F0 C"fan0" Q500                           ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0.8 H-1                               ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500                           ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45                              ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 S"HOT No,0" D0 H1 F0                   ; define tool 0
G10 P0 X0 Y0 Z0                                ; set tool 0 axis offsets
G10 P0 R0 S0                                   ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M501                                           ; load saved parameters from non-volatile memory
T0                                             ; select first tool

@droftarts thank you for your reply.
I'm on my way home from school, so I'll post it when I get there.