Posts made by ap742

Hi guys. I can't figure out or find how to get button "Print again" on the panel duet
all my duets have that button after print is done but not the new one

@Phaedrux
Thanks dude .

@wijkhuisen How did that work out.
thinking of doing the same thing

@Adamfilip
what do you mean make that area 0? how?

did you just edit heghtmap.csv and correct the numbers?

@Phaedrux

Z is typical ender 5 plus config nothing really changed there.
its 2mm pitch 4mm lead
10mm linear rods all lubed with synthetic lube
z is pretty smooth

driven by two steppers 0.8A 1.8 degree

here's my bed config

; bed.g
; called to perform automatic bed compensation via G32
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:05 GMT-0400 (Eastern Daylight Time)
M561 ; clear any bed transform
G29 ; probe the bed and enable compensation

so the way do it is

home all use 0.1 mm spacer to to get nozzle down to bed.
and repeat all this few times around all corners and center

than I run G31 S-1 few times to get average number for G31

after that I run G29

@Phaedrux

so before I tear down and re check all the bearings and stuff " all new but we all know there's always chance "

here's what map looks like not perfect but.....

this is the front of the bed between 275 & 300

this one is the back between 50 and 75

Thank You

@Phaedrux
Thank you
so I'm going to lean towards mechanical stuff . because its doing exactly the same thing as it did before

my starting gcode loads G29 S1 - assuming it should compensate

M106 S0 ; turn off cooling fan
G28
G29 S1
G92 E0 ; Reset Extruder
G1 Z10.0 F3000 ; Move Z Axis up little to prevent scratching of Heat Bed
G1 X344.5 Y300 Z0.28 F5000.0 ;Move to start position
G1 X344.5 Y90.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X344.7 Y90.0 Z0.28 F5000.0 ;Move to side a little
G1 X344.7 Y300 Z0.28 F1500.0 E30 ;Draw the second line

G92 E0 ; reset extrusion distance
G1 Z15.0 F6000 ;Move the nozzle up 15mm
G92 E0 ; Reset the extruder's origin

@Phaedrux

Thank You for that

so I got that changed

G31 P25 X41 Y-9.44 Z2.121

how about define the mesh

M557 X41:280 Y20:340 S38 if I do this it doesn't probe high end all the way

@Phaedrux

+x moves to the left from the end stop which is 0
+y moves to the front from the end stop which is 0

here's my config

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:05 GMT-0400 (Eastern Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5" ; set printer name

;MCU temp
M912 P0 S21 - 26

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E486.584 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E500.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I30 ;Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X355 Y343 Z400 S0 ; set axis maxima x350 M208 X350 Y350 Z400 S0 <- hemera

; Endstops
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z0 ; configure Z-probe endstop on Z
M591 P1 C"e0stop" S1 D0

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds H2.5
G31 P25 X-41 Y9.44 Z2.121 ; set Z probe trigger value, offset and trigger height
M557 X-41:280 Y20:340 S38 ; define mesh grid

; Heaters
;M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
;M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
;M140 H0 ; map heated bed to heater 0
;M143 H0 S120 ; set temperature limit for heater 0 to 120C
;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
;M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
;M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4725 C7.06e-8 ;M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S300 ; set temperature limit for heater 1 to 300C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
;591 D0 P2 C3 S1 ; Filament Run out sensor

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
M307 H1 R2.896 C205.2:122.7 D7.66 S1.00 V24.2

here's my homeall

; homeall.g
; called to home all axes
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri Apr 16 2021 19:18:06 GMT-0400 (Eastern Daylight Time)
G91 ; relative positioning
G1 H2 Z2.5 F6000 ; lift Z relative to current position
G1 H1 X-360.5 Y-355 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X-360.5 Y-355 F360 ; move slowly to X and Y axis endstops once more (second pass)
;G1 H1 Z-405 F360 ; move Z down stopping at the endstop
;G90 ; absolute positioning
;G92 Z0 ; set Z position to axis minimum (you may want to adjust this)
;G1 X220 Y175 F4000 ; Move probe to middle of bed
G1 X140 Y160 F6000 ; go to first probe point
M558 F500 A1 ; probe once quickly
G30
M558 F120 A10 ; detailed probe
G30

Thank You

hi guys I'm stuck. - running 3.4.4 duet 2 wifi - " printer Ender 5 plus "

was fine till I did exoslide upgrade and exoslide hotend.

pretty much moved my bltouch offset and stuff .

so I started from scratch
G31 P25 X-41 Y9.44 Z2.121
M557 X-41:280 Y20:340 S38

also added homeall because it wasn't compensating
M558 F500 A1 ; probe once quickly
G30
M558 F120 A10 ; detailed probe
G30

so this is latest G29

anyway no matter what the height map looks like - it'll print way to close to bed at the front of the bed

if I understand correct compensation happens when numbers bit negative ? if so how do I adjust for the map to be bit below the grid ?

@fcwilt I dont have Filament-error file
I am assuming I need to create one. - how?

I do have pause.g

pause.g
; called when a print from SD card is paused
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:27 GMT-0500 (Eastern Standard Time)
M83 ; relative extruder moves
G1 E-10 F3600 ; retract 10mm of filament
G91 ; relative positioning
G1 Z5 F360 ; lift Z by 5mm
G90 ; absolute positioning
G1 X0 Y0 F6000 ; go to X=0 Y=0

@phaedrux

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 Maestro version 3.3 (2021-06-15 21:47:01) running on Duet Maestro 1.0
Board ID: 08DJM-956DU-LLMS4-7J1FG-3SN6Q-KAM6Q
Used output buffers: 1 of 24 (11 max)
=== RTOS ===
Static ram: 23556
Dynamic ram: 73216 of which 0 recycled
Never used RAM 18724, free system stack 220 words
Tasks: NETWORK(ready,23.4%,270) HEAT(delaying,0.1%,345) Move(notifyWait,0.1%,407) TMC(notifyWait,1.3%,117) MAIN(running,75.0%,481) IDLE(ready,0.2%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:01:43 ago, cause: power up
Last software reset at 2021-12-04 10:44, reason: User, GCodes spinning, available RAM 18724, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00000000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 938
MCU temperature: min 31.0, current 32.9, max 33.4
Supply voltage: min 24.1, current 24.1, max 24.1, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 1: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 2: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 3: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 4: position 0, standstill, read errors 0, write errors 0, ifcnt 6, reads 17167, writes 6, timeouts 0, DMA errors 0
Driver 5: position 0, assumed not present
Driver 6: position 0, assumed not present
Date/time: 2021-12-04 12:54:14
Slowest loop: 3.50ms; fastest: 0.16ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 15.0MBytes/sec
SD card longest read time 3.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, maxWait 0ms, bed compensation in use: mesh, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1, chamberHeaters = -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: ok
=== Network ===
Slowest loop: 114.07ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
Interface state active, link 100Mbps half duplex

full config

; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Mon Nov 29 2021 17:18:26 GMT-0500 (Eastern Standard Time)

; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Maestro" ; set printer name

; Network
M552 P192.168.2.212 S1 ; enable network and set IP address
M553 P255.255.255.0 ; set netmask
M554 P192.168.1.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S1 ; physical drive 0 goes forwards
M569 P1 S1 ; physical drive 1 goes forwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z1600.00 E936.675 ; set steps per mm
M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X325 Y320 Z400 S0 ; set axis maxima

; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z

; Z-Probe
M950 S0 C"zprobe.mod";M950 S0 C"exp.heater7" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X44 Y2 Z2 ; set Z probe trigger value, offset and trigger height
M557 X0:310 Y0:285 S50 ;M557 X10:320 Y10:320 S50 ;M557 X0:305 Y0:315 S50 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S120 ; set temperature limit for heater 0 to 120C
M308 S1 P"e0temp" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S280 ; set temperature limit for heater 1 to 280C

; Fans
;M950 F0 C"!fan1" Q500 ; create fan 0 on pin !fan1 and set its frequency
;M106 P0 S1 H-1
M950 F0 C"fan1" Q500 ; create fan 0 on pin fan1 and set its frequency
M106 P0 S1 H-1
;M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
;M106 P0 S1 H-1 ; set fan 0 value. Thermostatic control is turned off
; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
M591 D0 P2 C"e0_stop" S1 ;M591 D0 P2 C3 S1 ; Filament Run out sensor
G29 S1 ; Load mesh bed
M564 H0 ; Process config overrides
M918 P1 E-4 ; Activate LCD12864

; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

Hi everyone
Just realized my runout sensor stopped working after upgrade to 3.3

M591 D0
Extruder 0 has no filament sensor

this is what I have in custom settings

; Custom settings
M591 D0 P2 C3 S1 ; Filament Run out sensor

so I replaced that with M591 D0 P2 C"e0_stop" S1
M591 D0
Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: no
M591 D0
Simple filament sensor on pin e0stop, enabled, output high when no filament, filament present: yes

it resolved - but temp shuts off when filament out
how do I tell it to keep bed temp on?

@dc42 after I asked the question I went to ready more and yah one day I learn how to read .. lol
I missed Upgrading ANY Duet 2 from 2.x to 3.0 or later requires installing 3.0 first.
anyway that did it . thank you for replying
I'm going to re do cable management-(have feeling it might have enough tension to do weird stuff and carriage and check bearings on my exoslids

Hi there was putting off upgrade for a while and finally did it.

but why does it still say Board: Duet Maestro 1.0 (duetmaestro100)
Firmware: RepRapFirmware for Duet 2 Maestro 2.04 (2019-11-01b1) I thought it was 3.3?

also

my map looks all kind of weird not sure how to fix it checked belts doesn't bad

here's my config

; Configuration file for Duet WiFi (firmware version 2.03)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v2.0.3 on Fri Sep 13 2019 00:35:32 GMT+0100 (British Summer Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"E5Maestro" ; set printer name

; Network
M552 P192.168.2.212 S1 ; enable network & set IP
M553 P255.255.255.0 ; set netmask
M554 P192.168.2.1 ; set gateway
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes forwards
M569 P1 S0 ; physical drive 1 goes backwards
M569 P2 S0 ; physical drive 2 goes backwards
M569 P3 S0 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ;M350 X64 Y64 Z64 E32 I0 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z800.00 E391.455 ;M92 X345.00 Y320.00 Z6400.00 E1873.35 ;hemeraE782.91 ; M92 X80.00 Y80.00 Z800.00 E407.53 ; set steps per mm - ;E792testing
M566 X900.00 Y900.00 Z12.00 E120.00 ;M566 X300.00 Y240.00 Z24.00 E3600.00 ;M566 X150.00 Y150.00 Z24.00 E3600.00 ; M566 X300.00 Y240.00 Z24.00 E3600.00 ; set maximum instantaneous speed changes (mm/min)
M203 X6000.00 Y6000.00 Z300.00 E1200.00 ;M203 X12000.00 Y12000.00 Z600.00 E6000.00 ;M203 X10000.00 Y10000.00 Z600.00 E6000.00 ; M203 X12000.00 Y12000.00 Z600.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z20.00 E500.00 ;M201 X2400.00 Y1800.00 Z20.00 E3600.00 ;M201 X900.00 Y900.00 Z15.00 E3600.00 ; M201 X2400.00 Y1800.00 Z20.00 E3600.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I30 ;M906 X800 Y800 Z800 E1000 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X325 Y320 Z410 S0 ; set axis maxima M208 X355 Y355 Z410 S0 /M208 X324 Y332 Z410 S0
; Endstops
M574 X2 Y2 S1 ; set active high endstops

; Z-Probe
M574 Z1 S2 ; set endstops controlled by probe
M558 P9 H2.5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
G31 P25 X-44 Y-2 Z1.389 ; set Z probe trigger value, offset and trigger height
M557 X20:285 Y20:310 S50 ; define mesh gridM557 X10:305 Y10:330 P5:5 - M557 X-5:282 Y5:299 P5:5 - what works M557 X10:305 Y10:330 P5:5 M557 X20:285 Y20:310 S40 good shit

; Heaters
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M305 P0 T100000 B4138 R2200 ; set thermistor + ADC parameters for heater 0
M143 H0 S130 ; set temperature limit for heater 0 to 130C
M305 P1 T100000 B4138 R2200 ; set thermistor + ADC parameters for heater 1
M143 H1 S280 ; set temperature limit for heater 1 to 260C

; Fans
M106 P0 S1 F500 H1 T45 ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P1 S0 F500 H-1 ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off

; Tools
M563 P0 D0 H1 F1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings
M591 D0 P2 C3 S1 ; Filament Run out sensor
G29 S1 ; Load mesh bed

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

M564 H0 ; Process config overrides
M918 P1 E-4 ; Activate LCD12864

;M593 F45

I think I found my mistake .

M574 X2 S1 P"xstop"
M574 Y2 S1 P"ystop"

had X&Y set to 1
changed it to 2 helped

@fcwilt Thanks that did help . but when it hits limit switch my x & y set to 0
when I tell it to move it right I guess - away from limit switch it stays there but + it'll try driving disregarding limit switch
https://drive.google.com/file/d/1C7-aKgCzSVuiECu2LyZn0p5qCil9Pxc7/view?usp=sharing

Morning all.
so I converted my ender 3 to duet it all went well (I though) till I added exoslid and New extruder discovered my x going backwords. changed that M569 P0 S0
now I can't figure out why my end stops, stop machine but will drive past it .

; Configuration file for Duet WiFi (firmware version 3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.2.3 on Fri May 14 2021 14:38:44 GMT-0400 (Eastern Daylight Time)

; General preferences
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Ender 3 Pro" ; set printer name
M918 P1 E4 F2000000 ; configure direct-connect display

; Network
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet

; Drives
M569 P0 S0 ; physical drive 0 goes backwards
M569 P1 S1 ; physical drive 1 goes backwards
M569 P2 S1 ; physical drive 2 goes forwards
M569 P3 S1 ; physical drive 3 goes backwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E936.675 ; set steps per mm 143.1 base
M566 X1200.00 Y1200.00 Z24.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X9000.00 Y9000.00 Z180.00 E6000.00 ; set maximum speeds (mm/min)
M201 X500.00 Y500.00 Z100.00 E5000.00 ; set accelerations (mm/s^2)
M906 X800 Y800 Z800 E1000 I50 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout

; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X233 Y235 Z260 S0 ; set axis maxima

; Endstops
;M574 X1 Y2 S1
M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
M574 Z0 ; configure Z-probe endstop on Z
M591 P1 C"e0stop" S1 D0

; Z-Probe
M950 S0 C"exp.heater3" ; create servo pin 0 for BLTouch
M558 P9 C"^zprobe.in" H2.5 F180 T6000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X-32 Y0 Z2.810 ; set Z probe trigger value, offset and trigger height
M557 X40:230 Y30:230 S40 ; define mesh grid

; Heaters
M308 S0 P"bedtemp" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
;M307 H0 B1 S1.00 ; enable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S150 ; set temperature limit for heater 0 to 150C
M308 S1 P"e0temp" Y"thermistor" T100000 B4092 ; configure sensor 1 as thermistor on pin e0temp
M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
;M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S275 ; set temperature limit for heater 1 to 275C

; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

; Tools
M563 P0 D0 H1 F0 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

; Custom settings are not defined

; Miscellaneous
M575 P1 S1 B57600 ; enable support for PanelDue
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

and here's home all

G91 ; relative positioning
G1 H2 Z5 F6000 ; lift Z relative to current position
G1 H1 X238 Y240 F3000 ; move quickly to X and Y axis endstops and stop there (first pass)
G1 H2 X5 Y5 F6000 ; go back a few mm
G1 H1 X238 Y240 F240 ; move slowly to X and Y axis endstops once more (second pass)
;G1 H1 Z265 F240 ; move Z down stopping at the endstop
G90 ; absolute positioning
G1 X178 Y109 F6000

@stephen6309 M557 X-25:320 Y10:320 S50 this works

I figured i'll do smaller squares or more probes

@stephen6309 had to make smaller . else it'll probe outside bed

@phaedrux said in Bed Mesh Skipping grid:

based on your config the endstops are at the low end, so the left side for x and the front for y. Is that correct?
When the x and y endstops are triggered the nozzle should be at 0,0 just at the corner of the bed based on your config. Is that correct?

when end stops triggered the hotend up right corner