Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. duettomio
    3. Posts
    • Profile
    • Following 1
    • Followers 0
    • Topics 4
    • Posts 19
    • Best 1
    • Controversial 0
    • Groups 0

    Posts made by duettomio

    • RE: lerge x mos module

      Never mind. I just found that polarity in the control wires is irrelevant.
      Heater works now.

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • RE: lerge x mos module

      @Phaedrux

      the wire resting on the Duett bed connector is the control wire of the lerge module.

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • RE: lerge x mos module

      @Phaedrux

      It is the above mentioned Lerge Mos module 25 A.

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • RE: lerge x mos module

      @ediik
      I just got around picking up where I left off.
      It says in the dozuki :" You can use a solid state relay (SSR) to switch the bed heater by connecting its control terminals to the Duet bed heater terminals. Make sure that you get the wires to the + and - control terminals of the SSR the right way round. "

      How do I verify which one is positive and is damage possible if I reverse it?
      These control wires are very thin.
      Thank you

      control cable.jpg

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • RE: How to find Z=0 ?

      Phrased another way: The bed moves up to make Z get smaller, eventually reaching Z0. Is the switch at the physical top of that movement?

      Yes, that's how it is. Sorry about the confusion.

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • RE: How to find Z=0 ?

      Yes, a mechanical end stop at min height

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • How to find Z=0 ?

      Hello Everyone,
      I am in the process of replacing a lergeX board with a Duet2 in a Two Trees Sapphire s coreXY.
      This is my first printer.
      So far it’s homing to all axes except Z because I have a dummy carriage installed.
      My next step is to install the carriage with the hot end and find Z=0.
      The printer has a mechanical and movable end stop at min height; the bed moves down.
      The bed has three adjustable screws to level it.

      My question is, what is the easiest approach to set Z height properly?

      Thank You.

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • RE: lead screw settings

      Thank you bearer for your help and pointing me in the right directions !

      posted in Tuning and tweaking
      duettomioundefined
      duettomio
    • RE: lead screw settings

      Right on. Z now moves exactly the requested amount.
      Thank You!

      My next step is to mount the carriage with the E3d hot end.
      So far I've used a dummy carriage holding a sharpie to simulate it.
      I know I have to set the end stop again.
      What is a good procedure to get it close to the bed and where should it stop?
      All I know is to use the bed level screws to set the distance, but where is the starting point?

      Cheers

      posted in Tuning and tweaking
      duettomioundefined
      duettomio
    • RE: lead screw settings

      M350 Z16

      So (200*16)/8=400

      How do I set this in config?

      posted in Tuning and tweaking
      duettomioundefined
      duettomio
    • RE: lead screw settings

      Thanks.
      I found Usongshine 17HS4401 has 200 steps/rev and 1.8°
      I measured 8mm travel per rev.
      I couldn't find the micosteps.

      posted in Tuning and tweaking
      duettomioundefined
      duettomio
    • lead screw settings

      Hello Everyone,
      I've replaced a lerge x board with a duet2 ethernet on a Two Trees sapphire s.
      So far I've got all axes homing correctly and the end stops set up.
      X and Y moves the right amount but Z moves a lot more than requested.
      I can't remember what I've entered in the reprap configurator for Z but I need to figure out how to change it.
      As far as I know, I have a T8 leadscrew with 2mm pitch (hard to find the specs for it).
      I would like to know how to figure out how to measure correctly and make the changes in the config file.

      Thank You

      posted in Tuning and tweaking
      duettomioundefined
      duettomio
    • RE: Endstop wiring order

      Worked great, thank you.

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • RE: Endstop wiring order

      Thank You.
      I'll try that today.

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • Endstop wiring order

      Hey Everyone,
      I am using the 3 wire end stop switches from my LergeX board, they are labeled C NO NC, but I have no clue how to connect them to the Duet2 to GND, 3V3, STP. I have already tried to connect one, but the board won't start on USB power.
      I'll have to re-crimp to the Duet2 connectors since they have different plugs.
      Any help appreciated, Thanks.
      20200408_002212.jpg

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • RE: Duet 3 wiring questions

      @dc42
      I was confused about that as well. In the wiring diagram it says left to right:
      2B, 2A, 1A, 1B so I guess the numbers refer to the phases, not the letters?

      as in Phase1, Phase1, Phase 2, Phase 2 ?

      Thanks.

      posted in Duet Hardware and wiring
      duettomioundefined
      duettomio
    • RE: lerge x mos module

      @zapta said in lerge x mos module:

      am suggest its control can be driven directly from the bed heater output of a board su

      Yes, that's it. Thank you.

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • RE: lerge x mos module

      It looks like it does have a two-wire control connection, but it also uses an adaptor module that ties in the thermistor.

      alt text

      alt text

      posted in Third-party add-ons
      duettomioundefined
      duettomio
    • lerge x mos module

      Hi all,
      I have a duet3d ethernet and am trying to replace a lerge x board in a two trees sapphire s printer.
      The lerge has this mos module powered directly by the ps to run the heated bed.
      Is it possible to use it in conjunction with the duet3d?

      Thank You, Patrick

      posted in Third-party add-ons
      duettomioundefined
      duettomio