@stephen6309 I've just discovered the problem.
In Simplify 3D I have in Gcode z offset in -1, so the Web panel starts in 0 but for gcode is really in -1, so first layer was 105% layer height of 0.6mm, thats 0,63mm, and second layer 0,6 more, thats 1,23mm, minus 1 because of the negative offset is the 0,23 that webpanel was showing me...

@dc42 the problem is solved... the issue was that my friend didn't put the wires in the right position after some changes and that was making all the malfunctions, sorry for all the mess created about that . Now they're working fine finally. Thanks for the help.

Hello again,
thank you so much, we just follow all the steps and WIFI is working again.

Thanks

Hello,

we bought in E3D-Online a Duet 3 Mainboard 6HC and WIFI stops working after a few months, started to lost the configuration of wifi and now we can't make it work anyway.

It's updated to the latest firmware and we can't make wifi works, see photo.

Anny suggestions?

Thanks

@phaedrux no, still on 3.3.

I don't know if I upgrade to beta if I can fix one thing and break a couple more...

@phaedrux I test this morning and it's very strange.

If I use M600 and send the GCODE, the machine pause, and then I can use the resume button and works fine.

But if I use the Pause button always fails...

any ideas?

@phaedrux any ideas? reading other issues of this error I think it's for the M350 and M906 that define X and Y motors that are with the external boards and drivers, but that can cause the problem of the resume?

Is this a known error in 3.3 version? that's why you're suggesting trying 3.4 beta?

@phaedrux I get this error:

Error: Setting not available for external drivers
Setting not available for external drivers
Warning: Heater 0 appears to be over-powered. If left on at full power, its temperature is predicted to reach 365C

@phaedrux sorry, didn't understand what you were asking. Here they are.resume.g pause.g config.g

@phaedrux
I have to finish some work in the machine and don't think can try new firmware on beta until 9th of December at least...

About my files, they are on my previous replys to @T3P3Tony all of them, config, pause and the new resume I updated after see the one that was wrong.

Now it seems to be failing all times I try to resume, any ideas?

@t3p3tony I try and first was try and error, here the M122 results

M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3S0-7JTD4-3S86P-9AJM9
Used output buffers: 1 of 40 (22 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92144 of which 0 recycled
Never used RAM 108288, free system stack 142 words
Tasks: NETWORK(ready,47.1%,224) ETHERNET(notifyWait,7.2%,117) HEAT(delaying,1.4%,325) Move(notifyWait,12.5%,247) CanReceiv(notifyWait,1.6%,774) CanSender(notifyWait,1.0%,362) CanClock(delaying,0.7%,339) TMC(notifyWait,132.8%,59) MAIN(running,49.8%,1092) IDLE(ready,0.0%,29), total 254.3%
Owned mutexes:
=== Platform ===
Last reset 117:09:14 ago, cause: power up
Last software reset details not available
Error status: 0x10
Aux0 errors 0,0,31
Step timer max interval 159
MCU temperature: min 35.3, current 45.4, max 48.9
Supply voltage: min 23.3, current 23.7, max 24.0, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.2, max 12.3, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/180/168, gc cycles 0
Driver 0: position 57128, standstill, reads 34586, writes 11 timeouts 0, SG min/max 0/0
Driver 1: position 19315, standstill, reads 34520, writes 77 timeouts 0, SG min/max 0/516
Driver 2: position 4736, standstill, reads 34520, writes 77 timeouts 0, SG min/max 0/537
Driver 3: position 0, standstill, reads 34587, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 34521, writes 77 timeouts 0, SG min/max 0/544
Driver 5: position 0, standstill, reads 34521, writes 77 timeouts 0, SG min/max 0/528
Date/time: 2021-11-24 17:02:06
Slowest loop: 244.06ms; fastest: 0.03ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 1.1ms, write time 799.9ms, max retries 0
=== Move ===
DMs created 125, maxWait 26493523ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5107, completed moves 5103, hiccups 0, stepErrors 0, LaErrors 0, Underruns [143, 23, 33], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X506.026 Y244.066 E49.3093" in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 12407519, received 5272477, lost 0, longest wait 1ms for reply type 6042, peak Tx sync delay 699, free buffers 49 (min 17), ts 2108775/2108774/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 800.86ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0

M122 40
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3S0-7JTD4-3S86P-9AJM9
Used output buffers: 1 of 40 (25 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92144 of which 0 recycled
Never used RAM 108288, free system stack 142 words
Tasks: NETWORK(ready,28.5%,224) ETHERNET(notifyWait,0.1%,117) HEAT(delaying,0.0%,325) Move(notifyWait,0.1%,247) CanReceiv(notifyWait,0.0%,774) CanSender(notifyWait,0.0%,362) CanClock(delaying,0.0%,339) TMC(notifyWait,8.0%,59) MAIN(running,63.3%,1092) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 117:10:02 ago, cause: power up
Last software reset details not available
Error status: 0x10
Aux0 errors 0,0,0
Step timer max interval 129
MCU temperature: min 45.0, current 45.2, max 45.5
Supply voltage: min 23.5, current 23.7, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/180/168, gc cycles 0
Driver 0: position 58154, standstill, reads 3028, writes 0 timeouts 0, SG min/max not available
Driver 1: position 19467, standstill, reads 3028, writes 0 timeouts 0, SG min/max 0/501
Driver 2: position 4736, standstill, reads 3027, writes 0 timeouts 0, SG min/max 0/512
Driver 3: position 0, standstill, reads 3027, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0, standstill, reads 3027, writes 0 timeouts 0, SG min/max 0/526
Driver 5: position 0, standstill, reads 3027, writes 0 timeouts 0, SG min/max 0/511
Date/time: 2021-11-24 17:02:54
Slowest loop: 3.09ms; fastest: 0.05ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 1.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5355, completed moves 5341, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is ready with "M122 40" in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X415.098 Y205.787 E0.4560 F4800" in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 1118, received 603, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 127, free buffers 49 (min 40), ts 240/240/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 3.44ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0

M122 41
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.3 (2021-06-15 21:45:47) running on Duet 3 MB6HC v1.01 or later (standalone mode)
Board ID: 08DJM-9P63L-DJ3S0-7JTD4-3S86P-9AJM9
Used output buffers: 1 of 40 (25 max)
=== RTOS ===
Static ram: 150904
Dynamic ram: 92144 of which 0 recycled
Never used RAM 108288, free system stack 142 words
Tasks: NETWORK(ready,28.4%,224) ETHERNET(notifyWait,0.1%,117) HEAT(delaying,0.0%,325) Move(notifyWait,0.1%,247) CanReceiv(notifyWait,0.0%,774) CanSender(notifyWait,0.0%,362) CanClock(delaying,0.0%,339) TMC(notifyWait,8.1%,59) MAIN(running,63.2%,1092) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 117:10:07 ago, cause: power up
Last software reset details not available
Error status: 0x10
Aux0 errors 0,0,0
Step timer max interval 125
MCU temperature: min 44.9, current 45.0, max 45.2
Supply voltage: min 23.4, current 23.7, max 23.8, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.1, current 12.1, max 12.2, under voltage events: 0
Heap OK, handles allocated/used 99/1, heap memory allocated/used/recyclable 2048/180/168, gc cycles 0
Driver 0: position 60177, standstill, reads 25223, writes 0 timeouts 0, SG min/max not available
Driver 1: position 18579, standstill, reads 25223, writes 0 timeouts 0, SG min/max 0/496
Driver 2: position 4736, standstill, reads 25223, writes 0 timeouts 0, SG min/max 0/506
Driver 3: position 0, standstill, reads 25223, writes 0 timeouts 0, SG min/max not available
Driver 4: position 0, standstill, reads 25223, writes 0 timeouts 0, SG min/max 0/513
Driver 5: position 0, standstill, reads 25223, writes 0 timeouts 0, SG min/max 0/506
Date/time: 2021-11-24 17:02:59
Slowest loop: 0.48ms; fastest: 0.05ms
=== Storage ===
Free file entries: 9
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.4ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 5374, completed moves 5366, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state 3
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 1
Movement lock held by null
HTTP is ready with "M122 41" in state(s) 0
Telnet is idle in state(s) 0
File is doing "G1 X415.097 Y237.788 E2.3978" in state(s) 0
USB is idle in state(s) 0
Aux is assembling a command in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty.
=== Filament sensors ===
Extruder 0 sensor: no filament
=== CAN ===
Messages queued 99, received 56, lost 0, longest wait 0ms for reply type 0, peak Tx sync delay 5, free buffers 49 (min 44), ts 23/23/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 2.43ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- Ethernet -
State: active
Error counts: 0 0 1 0 0
Socket states: 5 2 2 2 2 0 0 0