Posts made by flipps

@jay_s_uk thank you for your repliziert. sure:) version 1.02 pictures in the link. https://uploadnow.io/f/cpsvkqP

Hi, I have the problem that the fans on Fan0 and Fan 1 no longer do what they are supposed to do. I had to disassemble the hotend and assemble it after that they didn't run anymore. I've tested the following so far:
the fans and wiring are ok,
if I connect a fan directly to Fan 0 or Fan 1, nothing happens. By heating Or command M106 S127

The fans are configured as follows:
M106 P0 S0 I0 F500 H-1
M106 P1 S1 I0 F500 H1 T45

Firmware from Duet2wifi:
1.21 (2018-03-21)

@dc42 @DonStauffer I added

G1 Z10

before the line

G1 X{var.StartX + var.Width} Y{var.StartY} F{var.SpeedTravelXY}

This workes perfect
Thank you

Hi, what a great tool. I only have one question. I have a Delta printer and I have to set the starting point to X-70 and Y-70. Unfortunately, after the printer has been driven into the home, I only get error messages and the printer stops.

Error: in GCode file line 129 column 9: M117: string too long


Cancelled printing file 0:/gcodes/pat.gcode, print time was 0h 3m
Error: G0/G1: target position not reachable from current position

Error: in GCode file line 115 column 9: M117: string too long

I then tried it with starting point y0 and x0, it starts to print but of course the print does not fit on the bed. Could this be a problem with the negative values?
Maybe you still have an Idea wath i could try else

greetings Phil

Hi, is the connector set for the duet wifi available to reorder?

Hi, I think there is no Problem with the Cabel, i tested it with another Duet Wifi with other Cabels, i will take some Photos today in the evening

Hi, Yes i tried different Cables and the soldering Looks good.

Hi there,
I bought a Panel Due 5 last year, the new model, Unfortunately I had to find out that the display is still not woking with the 4 pin. Cabel, I tested it on two duets, it only works with the ribbon cable. Is there a special setting for this?
I have another Panel Due 5, the old version this works with both duets.
I have already contacted the sales service but maybe someone already has a tip.
Greetings from Germany

I have read the doku and changed the config.g as described. Are the files I uploadet not displayed?

Hi, I hope Google Translate it well.
I am currently updating my Sidewinder, he gets Duet Wifi with 5 inch display, sensorless homing and Pinda. I got it started, the probe responds to my Pei plate. Now I have problems with homing. When I drive an axis it drives home but does not stop walking. He rattles at the endstop, as well as the bed.
Homing macro.txt
homez.g
homey.g
homex.g
homeall.g
config.g

Does anyone have a good tip for me.
Greetings from Germany

Ok i will try, Thank you

Ok, can I reset the output from the sensor to 5 volts with a resistor?

Thank you for the answers:-)
Can I do that with the endstops? In the documentary is it about the Z-Probe, or I oversee the part with the Endstops?

Hi everyonbe,
I now intend to upgrade my second printer with a duet In the stock of the Sidwinder X1 I noticed that the endstops with 12 - 24 V work. For this I have attached a picture of the schematic. Is there a way to use them anyway?

Greetings from Germany
-Philipp

Hi, I have now rebuilt my TLM back to micro switch (thanks to the magnetic rods no problem) and started a new calibration, attached the pictures.

@veti Thank you for the rpley.
Yes i think that there everthing is fine, i will build th Tevo back to Microswitch Probe and check the bed again.

Here one more Highmap, only 10 Minutes Betwen the others.

Hi, I have a problem with mesh bed leveling. I use a Tevo little monster with Duet Wifi and panel due 5. I have now retrofitted the Smart effector 2.0. unfortunately, I get here no reasonable result with the leveling, it come out with each calibration different results. in the attachment times an example picture.
The heatbed is a PEI sheet with magnetic foil for fixation. I heat up the bed to 60 ° C!

Here the Config.g:

0_1561926445424_config.g

@veti Yes, Thank you

Hi, is it possible to get the plastic Bowden coupler as spare part? I broke mine Yesterday .
I had some at Home but in the wrong sice.
Greetings from Germany.