@droftarts said in 1LC TOOLBOARD v1.1. Accelerometer fail:
1N4148W
Thanks for the information, I will buy the diode and solder it, I hope this will solve the problem.
Latest posts made by Isaac López
-
RE: 1LC TOOLBOARD v1.1. Accelerometer failposted in Duet Hardware and wiring
-
RE: 1LC TOOLBOARD v1.1. Accelerometer failposted in Duet Hardware and wiring
@chrishamm The filament monitor is working fine with the new firmware 3.5.RC2, but the accelerometer continue showing the same error. My config.g is posted above.
-
RE: 1LC TOOLBOARD v1.1. Accelerometer failposted in Duet Hardware and wiring
This is my config.g.
The error message when the firmware resets because the filament sensor configuration is "DCS has been stoped"; Configuration file for Duet 3 (firmware version 3) ; executed by the firmware on start-up ; ; generated by RepRapFirmware Configuration Tool v3.1.4 on Wed Aug 05 2020 18:14:45 GMT+0200 (hora de verano de Europa central) ; General preferences M80 C"pson" ; Turns on the ATX power supply G90 ; send absolute coordinates... M83 ; ...but relative extruder moves M550 P"Duet 3" ; set printer name M669 K1 ; select CoreXY mode G4 S1 ; wait for expansion boards to start M955 P121.0 I10 ; Configure Accelerometer ; Drives M569 P0.0 S1 ; physical drive 0.0 goes forwards M569 P0.1 S1 ; physical drive 0.1 goes forwards M569 P0.2 S0 ; physical drive 0.2 goes forwards M569 P0.3 S1 ; physical drive 0.3 goes forwards M569 P0.4 S0 ; physical drive 0.4 goes forwards M569 P121.0 S0 ; physical drive 121.0 goes forwards M584 X0.1 Y0.0 Z0.2:0.4 E121.0 ; set drive mapping M671 X-63:368 Y0:0 S5 ; leadscrews at left (connected to Z) and right (connected to E1) of X axis M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation M92 X100.00 Y100.00 Z400.00 E655 ; set steps per mm M566 X500.00 Y500.00 Z24.00 E600.00 ; set maximum instantaneous speed changes (mm/min) M203 X25000.00 Y25000.00 Z1200.00 E7200.00 ; set maximum speeds (mm/min) M201 X20000.00 Y20000.00 Z300.00 E800.00 ; set maximum accelerations (mm/s^2) M204 P8000 T14000 ; set printing and travel accelerations M906 X1200 Y1200 Z1200 I30 ; set XYZ motor currents (mA) and motor idle factor in per cent M906 E1200 I10 ; set Extruder motor currents (mA) and motor idle factor in per cent M84 S30 ; Set idle timeout ; Pressure advance M572 D0 S0.035 ; Pressure advance ; Linear Compensation ;M592 D0 A0.015 B0.0012 L0.2 ; ; Dynamic Acceleration Adjustment M593 P"zvd" F25 ; Axis Limits M208 X-9 Y0 Z0 S1 ; set axis minima M208 X320 Y310 Z350 S0 ; set axis maxima ; Endstops M574 X1 S1 P"121.io2.in" ; configure active-high endstop for high end on X via pin io3.in M574 Y2 S1 P"io2.in" ; configure active-high endstop for high end on Y via pin io2.in M574 Z1 S2 ; configure Z-probe endstop for low end on Z ;Sensorless homing config ;M915 X S3 R0 F0 ; Z-Probe M950 S0 C"121.io0.out" ; create servo pin 0 for BLTouch M558 P9 C"121.io0.in" H3 F300 T20000 ; set Z probe type to bltouch and the dive height + speeds G31 P25 X-25 Y-15 Z1.6 ; set Z probe trigger value, offset and trigger height (+valor +bajo) M557 X30:270 Y30:270 P6:6 ; define mesh grid ; Heaters M308 S0 P"temp0" Y"thermistor" T100000 B3950 ; configure sensor 0 as thermistor on pin temp0 M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0 M307 H0 B0 S1.00 A140.1 C400.1 D6.8 V24.2 ; disable bang-bang mode for the bed heater and set PWM limit M140 H0 ; map heated bed to heater 0 M143 H0 S130 ; set temperature limit for heater 0 to 130C M308 S1 P"121.temp0" Y"thermistor" T100000 B4725 C7.06e-8 ; configure sensor 1 as thermistor on pin temp1 M950 H1 C"121.out0" T1 ; create nozzle heater output on out1 and map it to sensor 1 M307 H1 B0 R2.434 C196.7:173.0 D4.89 S1.00 V25.2 ; disable bang-bang mode for heater and set PWM limit M143 H1 S280 ; set temperature limit for heater 0 to 280C ; Fans M950 F0 C"121.out1" Q500 ; create fan 0 on pin out7 and set its frequency M106 C"Layer" P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off M950 F1 C"121.out2" Q500 ; create fan 1 on pin out8 and set its frequency M106 P1 S1 H1 T55 ; set fan 1 value. Thermostatic control is turned on M950 F2 C"out9" Q500 ; create fan 2 on pin out6 and set its frequency M106 C"Filtro" P2 S0 H-1 ; set fan 2 value. Thermostatic control is turned off ; Tools M563 P0 S"EVA2" D0 H1 F0 ; define tool 0 G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C ;Filament Sensor M591 D0 P1 C"121.io1.in" S1 ; Custom settings are not defined M564 H0 ;Allow Moving Axes Without Homing ; Miscellaneous M575 P1 S1 B57600 ; enable support for PanelDue M575 P2 S1 B57600 ; enable support for Neopixels M911 S20 R21 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power T0 ; select first tool -
1LC TOOLBOARD v1.1. Accelerometer failposted in Duet Hardware and wiring
Hi,
I have a 1LC toolboard v1.1 with firmware 3.5.0-RC.1 connected to a DUET3 MB6HC.
The input shaping addon show this error when trying to record a motion profile. "Error: Failed to start accelerometer data collection: INT1 error"
I read this happens beacuse this revision of the board have a missing diode. Its posible to solder this diode and what reference is needed?
I have another error with my filament switch sensor connected to the board, when i try to activate it the board resets all the time. Is it possible that this error also has some relationship with the diode? This is the command i use to activate the sensor: M591 D0 P1 C"121.io1.in" S1Thanks.