Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. madmattco
    3. Topics
    • Profile
    • Following 0
    • Followers 0
    • Topics 8
    • Posts 52
    • Best 1
    • Controversial 0
    • Groups 0

    Topics created by madmattco

    • madmattcoundefined

      Toolboard fan rpm reading

      Duet Hardware and wiring
      • • • madmattco
      4
      0
      Votes
      4
      Posts
      295
      Views

      madmattcoundefined

      @Phaedrux Yes it is. Glass beaded pa-12

    • madmattcoundefined

      Tool board pwm header

      Duet Hardware and wiring
      • • • madmattco
      6
      0
      Votes
      6
      Posts
      309
      Views

      dc42undefined

      Is it a 4 wire fan? If so then you need to invert the main pin in the M950 F command.

    • madmattcoundefined

      Solved DuetPi DWC differences

      Duet Web Control
      • • • madmattco
      8
      0
      Votes
      8
      Posts
      279
      Views

      madmattcoundefined

      @chrishamm said in DuetPi DWC differences:

      @chas2706 Clear your browser cache or try force-refreshing the page by pressing Ctrl+Shift+R in DWC and you should be good to go.

      All is well now. Thank you

    • madmattcoundefined

      Solved Tool board configuration

      Duet Hardware and wiring
      • • • madmattco
      23
      0
      Votes
      23
      Posts
      1.7k
      Views

      dintidundefined

      @dc42 Genuine, I only use genuine.
      I just tested with known good probe and it was a faulty probe, sigh. So much time wasted.
      Works fine on Toolboard.. tried getting it to work on io5 on Duet3 without luck though for some reason.

    • madmattcoundefined

      Missing dsf version from repo

      DSF Development
      • • • madmattco
      2
      0
      Votes
      2
      Posts
      106
      Views

      A Former User?

      Its published to the unstable list, ref https://forum.duet3d.com/post/143072

    • madmattcoundefined

      Duet wifi serial interface speed

      Duet Hardware and wiring
      • • • madmattco
      3
      0
      Votes
      3
      Posts
      198
      Views

      Danalundefined

      If you are planning to use the PanelDue port, be aware it is 3.3V TTL (not RS232)

    • madmattcoundefined

      Delta calibration issue

      General Discussion
      • • • madmattco
      10
      0
      Votes
      10
      Posts
      892
      Views

      madmattcoundefined

      @dc42 ty again sir! shes choochin proper now

    • madmattcoundefined

      Switch Z-probe not inverting

      Duet Hardware and wiring
      • • • madmattco
      46
      0
      Votes
      46
      Posts
      4.2k
      Views

      resamundefined

      @chrishamm coming back to one of the earlier issues here, something for the DWC wishlist:

      Would it be possible to make the Z-Probe box reflect the actual probe type?
      Currently DWC always displays the 0-1000 analog reading, which might be confusing for people with digital/switch-type probes.

      So, if its an analog type P1, P2, and P3 (?), then show the value 0-1000, as currently implemented.
      But if it is a switch-type / digital, P4 through P9, then just show "triggered" and "untriggered" - accounting for the invert-flag.
      Motor-stall detection P10 could be considered as P4-P9, or with "not stalled" and "stalled" strings.

      0_1530517222443_Screen Shot 2018-07-02 at 09.40.02.png

      One caveat: some people (including myself), reconfigure the probe type with multiple M558 commands in config.g and homez.g and various macros. To simplify things, I would suggest to only retrieve the probe type after booting (DWC connecting). Unless you think continuously querying M558 is reasonable (in non-printing states)?