Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    DWC2 bug: heater names not displayed correctly

    Scheduled Pinned Locked Moved
    Duet Web Control
    8
    23
    1.0k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • wilrikerundefined
      wilriker @deckingman
      last edited by

      @deckingman Hey Ian, I think the issue is that on the screenshot in the first post it shows "Heater 1" twice in the Tool box. Instead of "Heater 1" and "Heater 2". It is correct above the temperature chart.

      But you are right that essential information on versions and related config is missing.

      Manuel
      Duet 3 6HC (v0.6) with RPi 4B on a custom Cartesian
      with probably always latest firmware/DWC (incl. betas or self-compiled)
      My Tool Collection

      deckingmanundefined 1 Reply Last reply Reply Quote 0
      • deckingmanundefined
        deckingman @wilriker
        last edited by

        @wilriker In that case, then we also need to know how the tool has been defined.

        Ian
        https://somei3deas.wordpress.com/
        https://www.youtube.com/@deckingman

        1 Reply Last reply Reply Quote 0
        • remopiniundefined
          remopini @deckingman
          last edited by

          @deckingman if you look at my screenshot and post, you can see what I configured. Using the latest available 3.0 firmware bundle from github.

          wilrikerundefined 1 Reply Last reply Reply Quote 0
          • wilrikerundefined
            wilriker @remopini
            last edited by

            @remopini We still need to know what "platform" you run it on. Available candidates are

            • Duet3 + SBC
            • Duet3 or Duet2 (Wifi, Ethernet, Maestro) in standalone mode

            Also a full config.g can never hurt.

            Manuel
            Duet 3 6HC (v0.6) with RPi 4B on a custom Cartesian
            with probably always latest firmware/DWC (incl. betas or self-compiled)
            My Tool Collection

            remopiniundefined 1 Reply Last reply Reply Quote 0
            • remopiniundefined
              remopini @wilriker
              last edited by remopini

              @wilriker Sure, here you go:
              Board: Board: Duet Ethernet 1.04
              Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.0 (2020-01-03b3)
              DWC: Duet Web Control 2.0.4

              Sanitized config.g:

              ; Drives
              M569 P0 S0                              ; physical drive 0 goes backwards (X)
              M569 P1 S0                              ; physical drive 1 goes backwards (Y)
              M569 P2 S1                              ; physical drive 2 goes forwards (Z)
              M569 P3 S0                              ; physical drive 3 goes backwards (E0)
              M584 X0 Y1 Z2 E3                        ; set drive mapping
              M350 X16 Y16 Z16 E16 I1                 ; configure microstepping with interpolation
              M92 X80.00 Y80.00 Z400.00 E450.00       ; set steps per mm
              M566 X900.00 Y900.00 Z120.00 E120.00    ; set maximum instantaneous speed changes (mm/min)
              M203 X6000.00 Y6000.00 Z1800.00 E1200.00; set maximum speeds (mm/min)
              M201 X500.00 Y500.00 Z20.00 E250.00     ; set accelerations (mm/s^2)
              M906 X600 Y800 Z800 E800 I30            ; set motor currents (mA) and motor idle factor in per cent
              M84 S30                                 ; Set idle timeout
              
              ; Axis Limits
              M208 X0 Y0 Z0 S1                        ; set axis minima
              M208 X300 Y300 Z400 S0                  ; set axis maxima
              
              ; Endstops
              M574 X1 S1 P"!xstop"
              M574 Y1 S1 P"!ystop"
              M574 Z1 S1 P"!zstop"
              
              ; Z-Probe
              M558 P0 H5 F120 T6000                   ; disable Z probe but set dive height, probe speed and travel speed
              M557 X20:280 Y20:280 S65                ; define mesh grid
              G29 S1                                  ; read mesh grid from file
              
              ; Heaters
              M308 S0 P"bedtemp" Y"thermistor" A"Bed" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
              M950 H0 C"bedheat" T0                          ; create bed heater output on bedheat and map it to sensor 0
              M143 H0 S120                                   ; set temperature limit for heater 0 to 120C
              M307 H0 B0 S1.00                               ; disable bang-bang mode for the nozzle heater and set PWM limit
              M308 S1 P"e0temp" Y"thermistor" T100000 B4138  ; configure sensor 1 as thermistor on pin e0temp
              M950 H1 C"e0heat" T1                           ; create nozzle heater output on e0heat and map it to sensor 1
              M143 H1 S280                                   ; set temperature limit for heater 1 to 280C
              M307 H1 B0 S1.00                               ; disable bang-bang mode for the nozzle heater and set PWM limit
              
              ; Fans
              M106 P0 S0 I0 F500 H-1                  ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
              M106 P1 S0 I0 F500 H-1                  ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned off
              M106 P2 S1 I0 F500 H1 T45               ; set fan 2 value, PWM signal inversion and frequency. Thermostatic control is turned on
              
              ; Tools
              M563 P0 D0 H1 F1                        ; define tool 0 -> using FAN 1 (fritzed Fan 0)
              G10 P0 X0 Y0 Z0                         ; set tool 0 axis offsets
              G10 P0 R0 S0                            ; set initial tool 0 active and standby temperatures to 0C
              
              ; Custom settings are not defined
              M912 P0 S-3.2                           ; Calibrated MCU Temperature (reading is 3.2° too high)
              
              ; Miscellaneous
              M501                                    ; load saved parameters from non-volatile memory
              

              config-override.g

              M307 H0 A476.5 C791.3 D4.8 S1.00 V23.9 B0
              M307 H1 A1167.0 C239.9 D8.4 S1.00 V23.5 B0
              
              1 Reply Last reply Reply Quote 0
              • SIamundefined
                SIam
                last edited by SIam

                The same Problem here

                Board: Duet WiFi 1.02 or later + DueX5
                Firmware: RepRapFirmware for Duet 2 WiFi/Ethernet 3.0 (2020-01-03b3)
                Version von Duet WiFi Server: 1.23
                Duet Web Control 2.0.4

                in dwc1 the names are shown correctly

                dcw1-hypercube.png

                in dwc2 the names are missing so its impossible to switch betwen on/aktiv/standby

                dcw2-hypercube.png

                config.g

                ; Configuration file for Duet WiFi (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v2.1.4 on Sun Jan 05 2020 16:17:09 GMT+0100 (Mitteleuropäische Normalzeit)
                
                ; General preferences
                G90                                                 ; send absolute coordinates...
                M83                                                 ; ...but relative extruder moves
                M550 P"hypercube"                                   ; set printer name
                
                M667 S1                                             ; select CoreXY mode
                
                ; Network
                M552 S1                                             ; enable network
                M586 P0 S1                                          ; enable HTTP
                M586 P1 S1                                          ; disable FTP
                M586 P2 S1                                          ; disable Telnet
                
                ; Drives
                M569 P0 S0                                          ; physical drive 0 = X goes backwards
                M569 P1 S0                                          ; physical drive 1 = Y goes backwards
                M569 P2 S1                                          ; physical drive 2 = Z goes forwards
                M569 P3 S1                                          ; physical drive 3 = E0 goes forwards
                M569 P4 S1                                          ; physical drive 4 = Z goes forwards
                M569 P5 S0                                          ; physical drive 5 = Z goes backwards
                M569 P6 S1                                          ; physical drive 6 = E1 goes forwards
                
                M584 X0 Y1 Z2:4:5 E3                                  ; set drive mapping
                M671 X0:380:0 Y52:190:327 S3 F1.0; Leitspindeln links und rechts von der X-Achse ****
                M350 X16 Y16 Z16:16:16 E16 I1                          ; configure microstepping with interpolation
                M92 X200.60 Y200.60 Z797:797:797 E2666.67           ; set steps per mm
                M566 X600.00 Y600.00 Z300.00 E40.00          ; set maximum instantaneous speed changes (mm/min)
                M203 X30000.00 Y30000.00 Z1200.00 E4800.00     ; set maximum speeds (mm/min)
                M201 X2000.00 Y2000.00 Z500.00 E120.00          ; set accelerations (mm/s^2)
                M906 X1000 Y1000 Z1500.00 E500                        ; set motor currents (mA)
                M84 S0                                              ; Disable motor idle current reduction
                
                ; Axis Limits
                M208 X-1 Y0 Z-1 S1                                  ; set axis minima
                M208 X400 Y370 Z450 S0                              ; set axis maxima
                
                ; Endstops
                M574 X1 S1 P"xstop"                                 ; configure active-high endstop for low end on X via pin xstop
                M574 Y1 S1 P"ystop"                                 ; configure active-high endstop for low end on Y via pin ystop
                
                ; Z-Probe
                M558 P8 R0.4 C"^!zprobe.in+zprobe.mod" H5 F450 T6000 ;
                G31 P500 X0 Y0 Z-0.25                                 ; set Z probe trigger value, offset and trigger height
                M557 X15:390 Y15:370 S25                            ; define mesh grid
                
                ; Heaters
                M308 S0 P"bedtemp" Y"thermistor" A"Heizbett" T100000 B3950      ; configure sensor 0 as thermistor on pin bedtemp
                M950 H0 C"bedheat" T0                               ; create bed heater output on bedheat and map it to sensor 0
                M143 H0 S100                                        ; set temperature limit for heater 0 to 100C
                M307 H0 B0 S1.00                                    ; disable bang-bang mode for the nozzle heater and set PWM limit
                M308 S1 P"e0temp" Y"thermistor" A"Hotend" T100000 B4276       ; configure sensor 1 as thermistor on pin e0temp
                M950 H1 C"e0heat" T1                                ; create nozzle heater output on e0heat and map it to sensor 1
                M143 H1 S280                                        ; set temperature limit for heater 1 to 280C
                M307 H1 B0 S1.00                                    ; disable bang-bang mode for the nozzle heater and set PWM limit
                
                ; Fans
                M950 F0 C"fan0" Q25500 ;H-1                              ; create fan 0 on pin fan0 and set its frequency
                M106 P0 S0 H-1 F25500 C"Bauteilkühlung"                                  ; set fan 0 value. Thermostatic control is turned on
                M950 F1 C"fan1" Q75 T45 ;H1                              ; create fan 1 on pin fan1 and set its frequency
                M106 P1 S1 H1 T45 F75 C"Hotend"                                    ; set fan 1 value. Thermostatic control is turned off
                M950 F2 C"fan2" Q250 ;H-1                              ; create fan 2 on pin fan2 and set its frequency
                M106 P2 S0 H-1 F250 C"LED"                                  ; set fan 2 value. Thermostatic control is turned off
                
                ; Tools
                M563 P0 D0 H1 F0                                  ; define tool 0              *****
                G10 P0 X0 Y0 Z0                                     ; set tool 0 axis offsets
                G10 P0 R0 S0                                        ; set initial tool 0 active and standby temperatures to 0C
                
                ; Custom settings are not defined
                
                ; Miscellaneous
                M501                                                ; load saved parameters from non-volatile memory
                T0                                                  ; select first tool
                
                
                

                Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
                Duet WiFi 1.02 or later + DueX5
                RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
                Duet WiFi Server: 1.26
                Duet Web Control 3.4.0beta4 (2021-09-27)

                remopiniundefined DIY-O-Sphereundefined 2 Replies Last reply Reply Quote 0
                • remopiniundefined
                  remopini @SIam
                  last edited by remopini

                  @SIam You can still switch (by clicking on the blue "Bett" or "Werkzeug 0"), but it is highly annoying 🙂

                  1 Reply Last reply Reply Quote 0
                  • SIamundefined
                    SIam
                    last edited by

                    ok you are right 😮

                    Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
                    Duet WiFi 1.02 or later + DueX5
                    RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
                    Duet WiFi Server: 1.26
                    Duet Web Control 3.4.0beta4 (2021-09-27)

                    1 Reply Last reply Reply Quote 0
                    • wilrikerundefined
                      wilriker
                      last edited by wilriker

                      OK, since in all cases there is no DuetSoftwareFramework in play this means it's a bug in either RRF or DWC. I'll take a quick look at it.

                      EDIT: First result: DWC receives the list of correct names but fails to show them correctly in all places.

                      Manuel
                      Duet 3 6HC (v0.6) with RPi 4B on a custom Cartesian
                      with probably always latest firmware/DWC (incl. betas or self-compiled)
                      My Tool Collection

                      1 Reply Last reply Reply Quote 0
                      • DIY-O-Sphereundefined
                        DIY-O-Sphere @SIam
                        last edited by DIY-O-Sphere

                        @SIam
                        c265bca1-51e3-4077-b092-3bfe8854c8db-grafik.png
                        I have named tools (not the fans) and the heaters are clickable.
                        ~~I see it that way, the fan names are displayed In the graph and the tool names are displayed in the menu. And they can differ.
                        Maybe the graph should also display tools and not fans.

                        Edit: The fan names are only displayed when no tool names are defined.~~

                        (UTC+1)

                        remopiniundefined 1 Reply Last reply Reply Quote 0
                        • remopiniundefined
                          remopini @DIY-O-Sphere
                          last edited by

                          @DIY-O-Sphere It's not fans, it's heaters and showing tools instead of heaters in a temperature chart is a bad idea, because there isn't necessarily one heater for one tool (a tool could have 2 or more heaters or none).

                          DIY-O-Sphereundefined 1 Reply Last reply Reply Quote 0
                          • DIY-O-Sphereundefined
                            DIY-O-Sphere @remopini
                            last edited by DIY-O-Sphere

                            @remopini
                            You are right. Forget about my post.
                            I thought that are the fan names, but that is not correct. ace702ec-93cf-4618-8df5-8e403390ef69-grafik.png
                            Who can read is clearly at an advantage. 👎

                            (UTC+1)

                            1 Reply Last reply Reply Quote 0
                            • SIamundefined
                              SIam
                              last edited by

                              maybe another bug :

                              on the page /Job/Status only one from two (*three) Fan's shown:
                              status-fan-hypercube.png

                              here you see two fan's are enabled
                              if i only disable the bauteilkühler then i get the message that there are no fans
                              status-fan-show-hypercube.png

                              on the main page i think it's ok *because the third fan is for the hotend
                              overview-fan-hypercube.png

                              Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
                              Duet WiFi 1.02 or later + DueX5
                              RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
                              Duet WiFi Server: 1.26
                              Duet Web Control 3.4.0beta4 (2021-09-27)

                              1 Reply Last reply Reply Quote 0
                              • chrishammundefined
                                chrishamm administrators
                                last edited by

                                Can you please check if this is fixed in DWC 2.0.6?

                                Duet software engineer

                                1 Reply Last reply Reply Quote 0
                                • SIamundefined
                                  SIam
                                  last edited by

                                  yes it works with 2.0.6 thank you !

                                  Hypercube-Evolution-Hybrid, Piezo Orion, Orbiter
                                  Duet WiFi 1.02 or later + DueX5
                                  RepRapFirmware for Duet 2 WiFi/Ethernet 3.4.0beta4 (2021-09-27 11:30:36)
                                  Duet WiFi Server: 1.26
                                  Duet Web Control 3.4.0beta4 (2021-09-27)

                                  1 Reply Last reply Reply Quote 0
                                  • First post
                                    Last post
                                  Unless otherwise noted, all forum content is licensed under CC-BY-SA