Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    RepRapFirmware 3.01-RC3 released

    Scheduled Pinned Locked Moved
    Beta Firmware
    22
    68
    4.3k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • DaBitundefined
      DaBit
      last edited by

      @dc42 said in RepRapFirmware 3.01-RC3 released:

      You could run it faster than that if you use a loop within the daemon.g file.

      I suppose I could, but as long as I do not have to interface with existing boards the frequency is not that important.

      How do we prevent the daemon task from taking away too much processing from the main G-code pipe? Is an endless while() harmful? Or is all that handled by priority in RRF?

      Anyway, nice addition that daemon task!
      I could use the daemon task to monitor the heaters for faulting, generate a chargepump signal when OK, quit generating the chargepump and send an M81 when failing.

      dc42undefined 1 Reply Last reply Reply Quote 0
      • Danalundefined
        Danal @imrj
        last edited by Danal

        @imrj said in RepRapFirmware 3.01-RC3 released:

        @bearer bossa crashes on my Mac running Movaje, and i dont have a laptop w Windows, so I would have to rip out the board and uncable it all, trying to avoid that......
        I tried the file "Duet3_SDiap_MB6HC.bin" that someone posted the link for but it still wont take, it says soemthing about in-app error (i notices is a really small file of 55k vs. the usual 550k or so).....I dunno this shouldnt be that difficult....help!!

        Do you have a Raspberry Pi?

        The instructions for bossa on Pi are on the dozuki, just below the instructions for Winders (<=Texas edition of WIndows)

        Delta / Kossel printer fanatic

        imrjundefined 1 Reply Last reply Reply Quote 0
        • imrjundefined
          imrj @Danal
          last edited by

          @Danal i do have plenty those, thanks, will give that a shot

          1 Reply Last reply Reply Quote 0
          • droftartsundefined
            droftarts administrators @imrj
            last edited by

            @imrj said in RepRapFirmware 3.01-RC3 released:

            bossa crashes on my Mac running Movaje

            See https://forum.duet3d.com/topic/11445/flashing-firmware-on-mac-os-x

            Ian

            Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

            1 Reply Last reply Reply Quote 0
            • dc42undefined
              dc42 administrators @DaBit
              last edited by

              @DaBit said in RepRapFirmware 3.01-RC3 released:

              How do we prevent the daemon task from taking away too much processing from the main G-code pipe? Is an endless while() harmful?

              If using your own loop, then I recommend that you include at least one G4 command in it with a reasonable length of delay.

              Duet WiFi hardware designer and firmware engineer
              Please do not ask me for Duet support via PM or email, use the forum
              http://www.escher3d.com, https://miscsolutions.wordpress.com

              1 Reply Last reply Reply Quote 0
              • dc42undefined
                dc42 administrators @imrj
                last edited by

                @imrj said in RepRapFirmware 3.01-RC3 released:

                I tried the file "Duet3_SDiap_MB6HC.bin" that someone posted the link for but it still wont take, it says soemthing about in-app error (i notices is a really small file of 55k vs. the usual 550k or so).....I dunno this shouldnt be that difficult....help!!

                That's the new IAP file, used by RRF 3.0 and later to upgrade the firmware. It is not the firmware file itself, but it needs to be present in /sys when you want to upgrade the firmware using DWC or M997.

                Duet WiFi hardware designer and firmware engineer
                Please do not ask me for Duet support via PM or email, use the forum
                http://www.escher3d.com, https://miscsolutions.wordpress.com

                1 Reply Last reply Reply Quote 0
                • imrjundefined
                  imrj
                  last edited by

                  I understand, but even with it present and the firmware file, still does nothing, it says is updating the firmware, but it remains the same in M115 afterwards, stuck at 3.0B12

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Phaedruxundefined
                    Phaedrux Moderator @imrj
                    last edited by

                    @imrj Try updating to 3.0 first, with the zip file from that release. Then try updating to this release.

                    Z-Bot CoreXY Build | Thingiverse Profile

                    1 Reply Last reply Reply Quote 1
                    • imrjundefined
                      imrj
                      last edited by

                      i was able to finally get it done with the DuetPI and using the virtual SD card, so its all good now...but this needs to be simplied a bit, too hard for just a firmware update
                      now I have another issue but opened a new post for that one....thanks everyone

                      droftartsundefined 1 Reply Last reply Reply Quote 0
                      • droftartsundefined
                        droftarts administrators @imrj
                        last edited by

                        @imrj Did you see my post about fixing bossa on Mac OS? https://forum.duet3d.com/topic/11445/flashing-firmware-on-mac-os-x

                        Ian

                        Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                        imrjundefined 1 Reply Last reply Reply Quote 0
                        • imrjundefined
                          imrj @droftarts
                          last edited by

                          @droftarts yea i did thanks, but by then i had already setup the DuetPi and got it working....but yea i will do this to my Macbook, but interestingly enough I did have brew already installed and using it for other things

                          droftartsundefined 1 Reply Last reply Reply Quote 0
                          • droftartsundefined
                            droftarts administrators @imrj
                            last edited by

                            @imrj it's not just brew, you need to 'brew install wxwidgets'.

                            Ian

                            Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

                            imrjundefined 1 Reply Last reply Reply Quote 0
                            • TurtlePrintundefined
                              TurtlePrint
                              last edited by TurtlePrint

                              When sending the M112 command the printer turns off and then starts the hot end fan "fan1" at full speed. I'm hoping to use the new daemon.g file to monitor a rotor stuck alarm wire on the hot end fan and send an M112 if its detected. So the fan continuing to spin after M112 is problematic if it's in a known stuck position.

                              Printer is running:
                              Duet2Wifi w/Duex5 running RRF RC3

                              config.g snippet

                              ; Fans
                              M950 F0 C"Fan0"						;Define the Parts Blower Fan connected to Fan0
                              M106 P0 S0 C"Parts Blower" H-1 		;Name the fan, turn off thermistic control and turn the fan off if it was running
                              M950 F1 C"Fan1"						;Define the Tool Fan connected to Fan1
                              M106 P1 T40 H1						;Enable Thermostatic Control to turn fan on 40 degrees
                              

                              Edit: After some experimentation it appears that any fan with thermostatic control enabled is set to 100% after an M112 command. Is this the intended behavior?

                              dc42undefined c310undefined 2 Replies Last reply Reply Quote 0
                              • imrjundefined
                                imrj @droftarts
                                last edited by

                                @droftarts ah ok got it, will do that

                                1 Reply Last reply Reply Quote 0
                                • JuKuundefined
                                  JuKu
                                  last edited by

                                  M203 is set by mm/min, but reported back in mm/sec. (not a problem and as documented, just a bit odd. ?.)

                                  1 Reply Last reply Reply Quote 0
                                  • dc42undefined
                                    dc42 administrators @TurtlePrint
                                    last edited by

                                    @TurtlePrint said in RepRapFirmware 3.01-RC3 released:

                                    Edit: After some experimentation it appears that any fan with thermostatic control enabled is set to 100% after an M112 command. Is this the intended behavior?

                                    If readings from the sensor that control the thermostatic fan are not available, the firmware assumes that whatever it is supposed to cool might be hot, so it turns the fan on.

                                    Duet WiFi hardware designer and firmware engineer
                                    Please do not ask me for Duet support via PM or email, use the forum
                                    http://www.escher3d.com, https://miscsolutions.wordpress.com

                                    1 Reply Last reply Reply Quote 0
                                    • dc42undefined
                                      dc42 administrators
                                      last edited by

                                      There is a bug in the 3.01-RC3 firmware on Tool Boards. The symptom of this bug is that the motor doesn't move and M122 reports a large number of timeouts for Driver 0. I have put a fixed version of Duet3Firmware-TOOL1LC.bin at https://www.dropbox.com/sh/3azy1njy3ayjsbp/AACquxr2m00eV568RZg5QG5wa?dl=0. Tool board users, please use this version until I release 3.01-RC4.

                                      Duet WiFi hardware designer and firmware engineer
                                      Please do not ask me for Duet support via PM or email, use the forum
                                      http://www.escher3d.com, https://miscsolutions.wordpress.com

                                      1 Reply Last reply Reply Quote 0
                                      • arhiundefined
                                        arhi
                                        last edited by

                                        so far so good, duet2eth, one 6h print done flawlesly, second is 4h-38% in doing ok another 60% and change to go

                                        1 Reply Last reply Reply Quote 0
                                        • c310undefined
                                          c310 @Danal
                                          last edited by

                                          @Danal said in RepRapFirmware 3.01-RC3 released:

                                          emergency stop

                                          on duetwifi i have upgraded from 3.0 and emergency stop now does not work at all (was buggy in 3.0: printer stopped but did not reload itself, i was cycling power off-on to finish emergency stop cycle 🙂

                                          current config

                                          M950 J1 C"e1stop"
                                          M581 P"e1stop" T0 C0
                                          

                                          3.0 config was

                                          M581 P"e1stop" T0
                                          

                                          what should i fix ?

                                          1 Reply Last reply Reply Quote 0
                                          • dc42undefined
                                            dc42 administrators
                                            last edited by dc42

                                            https://duet3d.dozuki.com/Wiki/Gcode#Section_M581_RepRapFirmware_3_01RC2_and_later

                                            P is now the GPin pin number, so 1 in your case

                                            Duet WiFi hardware designer and firmware engineer
                                            Please do not ask me for Duet support via PM or email, use the forum
                                            http://www.escher3d.com, https://miscsolutions.wordpress.com

                                            c310undefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA