Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. imrj
    • Profile
    • Following 0
    • Followers 0
    • Topics 12
    • Posts 73
    • Best 1
    • Controversial 0
    • Groups 0

    imrj

    @imrj

    2
    Reputation
    6
    Profile views
    73
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    imrj Unfollow Follow

    Best posts made by imrj

    • RE: duet ethernet blew both fuses, replacing hasnt helped

      ok i took care of the problem......

      2020-02-29.jpg

      posted in Duet Hardware and wiring
      imrjundefined
      imrj

    Latest posts made by imrj

    • RE: High Temperature printing

      i print 500C easily with a dyze hotend and extruder....works all day long

      posted in General Discussion
      imrjundefined
      imrj
    • RE: Duet Wifi external antenna upgrade - damaged SD socket latch

      @engikeneer that happened to me, i did even worse and broke some of the solder points....but is no big deal the pinouts for the duet are well documented and the SDcard is SPI if i recall, so i just followed some traces to make the connection work again...just study the boards circuitry before you do anything else

      posted in Duet Hardware and wiring
      imrjundefined
      imrj
    • RE: Adding wifi to a duet 3

      well on the duet2 i swapped a wifi to ethernet and also the reserved (added wifi to Eth) and it worked just fine in both cases, you will just need to give up that SPI port I think , just use a decent wifi module like ESP12 with some external antenna and give it a shot, unless they went as far to the effort of removing wifi support native from RRF3

      posted in General Discussion
      imrjundefined
      imrj
    • RE: bed heater output > 125C not allowed....Duet3/RRF3

      @dc42 RepRapFirmware for Duet 3 MB6HC version 3.01-RC5 running on Duet 3 MB6HC v0.6 or 1.0

      posted in General Discussion
      imrjundefined
      imrj
    • RE: Stringing problem corexy

      the max retraction speed for the Dyze is 25mm/s , but i will try the other settings....i can always go higher than 25 but am sure will be clogging time

      posted in Example setups and prints
      imrjundefined
      imrj
    • RE: bed heater output > 125C not allowed....Duet3/RRF3

      ok yup the M143 H0 P0 S150 did the job, all is well......RRF3 keeps playing tricks on me

      posted in General Discussion
      imrjundefined
      imrj
    • RE: For anyone still using endstop switches...

      wouldnt optical anything be a problem given we usually dont have printers in a super clean area? I mean mine isnt dirty, but sure not dust free....
      my home water treatment system used an optical sensor for something (forgot what it was) but it used to go out like once every 6 months....it uses something else now.....

      posted in General Discussion
      imrjundefined
      imrj
    • bed heater output > 125C not allowed....Duet3/RRF3

      i have ran as high as 150C on my older Duet2 no problem, some materials like ABS need it and I have an A/C bed with SSR relay so it heats up pretty quick....where is the restriction coming from because in my config.g I have the line below, but it doesnt seem to care, it cuts off after 125C regardless.....do I need to move it to another heater output?

      M308 S0 P"temp0" Y"thermistor" T100000 B4092 ; configure sensor 0 as thermistor on pin temp0
      M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
      M143 H0 S150 ; set temperature limit for heater 0 to 150C
      M307 H0 A450.2 C282.2 D6.3 S1.00 V0.0 B0
      M140 H0 ; map heated bed to heater 0

      posted in General Discussion
      imrjundefined
      imrj
    • RE: Varifying Bed Temp?

      i havent had an issue with running mine up to 150c and just a chinese sensor, i also have metal plate, glass, copper sheet and PEI and it does ok, printing ABS and other tough materials and the temp readings appear to be correct or I would be having issues

      posted in Tuning and tweaking
      imrjundefined
      imrj
    • RE: Stringing problem corexy

      am having issue with stringing too with TPU....can someone clarify how to approach a setting for retraction speed? I know from past experience if I make my Dyze Xtruder retract too fast it will clog....

      posted in Example setups and prints
      imrjundefined
      imrj