Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Cambio elettronica

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    9
    124
    6.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • Leblondundefined
      Leblond
      last edited by

      @droftarts said in Cambio elettronica:

      M564 S0 H0
      ho lanciato il comando M564 S0 H0, poi G1 X50 F200 non funziona, quindi ho provato a mandare l'asse x in home, ma mi si e' alzato l'asse Z, forse qualcosina non quadra

      droftartsundefined 1 Reply Last reply Reply Quote 0
      • droftartsundefined
        droftarts administrators @Leblond
        last edited by

        @Leblond It sounds like you have connected the stepper motors to the wrong pins! See the wiring diagram here for the motor connections: https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams

        If your wiring is correct, post your config.g file. Also send M115 and post the response.

        Ian

        Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

        1 Reply Last reply Reply Quote 0
        • Leblondundefined
          Leblond
          last edited by

          0:/sys/config.g.bak
          ; Configuration file for Duet WiFi (firmware version 3)
          ; executed by the firmware on start-up
          ;
          ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale)

          ; General preferences
          G90 ; send absolute coordinates...
          M83 ; ...but relative extruder moves
          M550 P"X5SA PRO" ; set printer name

          M667 S1 ; select CoreXY mode

          ; Network
          M552 S1 ; enable network
          M586 P0 S1 ; enable HTTP
          M586 P1 S0 ; disable FTP
          M586 P2 S0 ; disable Telnet

          ; Drives
          M569 P0 S1 ; physical drive 0 goes forwards
          M569 P1 S0 ; physical drive 1 goes backwards
          M569 P2 S0 ; physical drive 2 goes backwards
          M569 P3 S0 ; physical drive 3 goes backwards
          M584 X0 Y1 Z2 E3 ; set drive mapping
          M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
          M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
          M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
          M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
          M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
          M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
          M84 S30 ; Set idle timeout

          ; Axis Limits
          M208 X0 Y0 Z0 S1 ; set axis minima
          M208 X330 Y330 Z400 S0 ; set axis maxima

          ; Endstops
          M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
          M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
          M574 Z1 S2 ; configure Z-probe endstop for low end on Z

          ; Z-Probe
          M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
          G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
          M557 X60:300 Y50:300 S20 ; define mesh grid

          ; Heaters
          M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
          M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
          M143 H0 S120 ; set temperature limit for heater 0 to 120C
          M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
          M140 H0 ; map heated bed to heater 0
          M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
          M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
          M143 H1 S280 ; set temperature limit for heater 1 to 280C
          M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

          ; Fans
          M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
          M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
          M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
          M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

          ; Tools
          M563 P0 D0 H1 F0 ; define tool 0
          G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
          G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

          ; Custom settings are not defined

          ; Miscellaneous
          M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

          droftartsundefined 2 Replies Last reply Reply Quote 0
          • droftartsundefined
            droftarts administrators @Leblond
            last edited by

            @Leblond said in Cambio elettronica:

            config.g.bak

            That's the backup file. Post 'config.g'.

            Ian

            Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

            1 Reply Last reply Reply Quote 0
            • droftartsundefined
              droftarts administrators @Leblond
              last edited by

              @Leblond said in Cambio elettronica:

              M584 X0 Y1 Z2 E3

              That looks okay. Note that the order of the driver pins on the board, from left to right, is E1, E0, X, Y, Z.

              Ian

              Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

              1 Reply Last reply Reply Quote 0
              • Leblondundefined
                Leblond
                last edited by

                ; Configuration file for Duet WiFi (firmware version 3)
                ; executed by the firmware on start-up
                ;
                ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale)

                ; General preferences
                G90 ; send absolute coordinates...
                M83 ; ...but relative extruder moves
                M550 P"X5SA PRO" ; set printer name

                ;M667 S1 ; select CoreXY mode
                M669 K1
                ; Network
                M552 S1 ; enable network
                M586 P0 S1 ; enable HTTP
                M586 P1 S0 ; disable FTP
                M586 P2 S0 ; disable Telnet

                ; Drives
                M569 P0 S1 ; physical drive 0 goes forwards
                M569 P1 S0 ; physical drive 1 goes backwards
                M569 P2 S0 ; physical drive 2 goes backwards
                M569 P3 S0 ; physical drive 3 goes backwards
                M584 X0 Y1 Z2 E3 ; set drive mapping
                M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
                M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
                M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
                M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
                M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
                M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
                M84 S30 ; Set idle timeout

                ; Axis Limits
                M208 X0 Y0 Z0 S1 ; set axis minima
                M208 X330 Y330 Z400 S0 ; set axis maxima

                ; Endstops
                M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
                M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
                M574 Z1 S2 ; configure Z-probe endstop for low end on Z

                ; Z-Probe
                M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
                G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
                M557 X60:300 Y50:300 S20 ; define mesh grid

                ; Heaters
                M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
                M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
                M143 H0 S120 ; set temperature limit for heater 0 to 120C
                M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
                M140 H0 ; map heated bed to heater 0
                M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
                M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
                M143 H1 S280 ; set temperature limit for heater 1 to 280C
                M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

                ; Fans
                M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
                M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
                M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
                M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

                ; Tools
                M563 P0 D0 H1 F0 ; define tool 0
                G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
                G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

                ; Custom settings are not defined

                ; Miscellaneous
                M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

                1 Reply Last reply Reply Quote 0
                • Leblondundefined
                  Leblond
                  last edited by

                  sicuramente e' tutto sbagliato ma l'ho fatto con il configuratore reprap

                  1 Reply Last reply Reply Quote 0
                  • Leblondundefined
                    Leblond
                    last edited by

                    20200331_185549.jpg

                    1 Reply Last reply Reply Quote 0
                    • Leblondundefined
                      Leblond
                      last edited by

                      l'unico problema elettrico che ho riscontrato e' il colore dei fili
                      2b rosso
                      2a blu
                      1a verde
                      1b nero

                      ma la connessione dei fili dei motori sono invertiti le fasi 1a e 1b
                      che sia quello?

                      1 Reply Last reply Reply Quote 0
                      • Leblondundefined
                        Leblond
                        last edited by

                        cioe' i cavi dei motori che dovrebbero essere 2b-R 2a-B 1a-V 1b-N sui fili 1a e 1b sono invertiti

                        1 Reply Last reply Reply Quote 0
                        • Leblondundefined
                          Leblond
                          last edited by

                          G28
                          Error: Z probe already triggered at start of probing move

                          1 Reply Last reply Reply Quote 0
                          • Leblondundefined
                            Leblond
                            last edited by

                            Ragazzi ho realmente bisogno di voi, non ce ne salto fuori, mi continua a dare come errore Z probe already triggered at start of probing move

                            1 Reply Last reply Reply Quote 0
                            • Leblondundefined
                              Leblond
                              last edited by

                              Non so come fargli cambiare stato

                              1 Reply Last reply Reply Quote 0
                              • Leblondundefined
                                Leblond
                                last edited by

                                smanettando qualcosa e' cambiato non so il perche' ma nel file home x e y invece di sondare a 0 sondava a 335
                                adesso l'errore e' cambiato dicendomi G0/G1: insufficient axes homed

                                1 Reply Last reply Reply Quote 0
                                • Phaedruxundefined
                                  Phaedrux Moderator
                                  last edited by

                                  https://duet3d.dozuki.com/Wiki/FAQ#Section_I_get_this_error_message_Error_G0_G1_insufficient_axes_homed

                                  Z-Bot CoreXY Build | Thingiverse Profile

                                  Leblondundefined 1 Reply Last reply Reply Quote 0
                                  • Leblondundefined
                                    Leblond @Phaedrux
                                    last edited by

                                    @Phaedrux ; homeall.g
                                    ; called to home all axes
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 22:19:23 GMT+0200 (Ora legale dell’Europa centrale)
                                    G91 ; relative positioning
                                    G1 H2 Z10 F3000 ; lift Z relative to current position
                                    G1 H1 X0 Y0 F500 ; move quickly to X or Y endstop and stop there (first pass)
                                    G1 H1 X0 ; home X axis
                                    G1 H1 Y0 ; home Y axis
                                    G1 X-5 Y-5 F500 ; go back a few mm
                                    G1 H1 X0 F360 ; move slowly to X axis endstop once more (second pass)
                                    G1 H1 Y0 ; then move slowly to Y axis endstop
                                    G90 ; absolute positioning
                                    G1 X60 Y50 F500 ; go to first bed probe point and home Z
                                    G30 ; home Z by probing the bed

                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91 ; relative positioning
                                    ;G1 Z10 F50 ; lift Z relative to current position
                                    ;G90 ; absolute positioning

                                    Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                    • Leblondundefined
                                      Leblond
                                      last edited by

                                      ; homez.g
                                      ; called to home the Z axis
                                      ;
                                      ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 22:19:24 GMT+0200 (Ora legale dell’Europa centrale)
                                      G91 ; relative positioning
                                      G1 H2 Z-9999 F3000 ; lift Z relative to current position
                                      G90 ; absolute positioning
                                      G1 X60 Y50 F3000 ; go to first probe point
                                      G30 ; home Z by probing the bed

                                      ; Uncomment the following lines to lift Z after probing
                                      ;G91 ; relative positioning
                                      ;G1 Z10 F50 ; lift Z relative to current position
                                      ;G90 ; absolute positioning

                                      1 Reply Last reply Reply Quote 0
                                      • Leblondundefined
                                        Leblond
                                        last edited by

                                        a sembra tutto ok, ma posso anche sbagliarmi

                                        1 Reply Last reply Reply Quote 0
                                        • Leblondundefined
                                          Leblond
                                          last edited by

                                          ok ho fatto esperimento, ho mandato gli assi in home mettendo una parte mettalica sotto il sensore ma questo pur segnando 0 partendo da 1000 non si ferma

                                          1 Reply Last reply Reply Quote 0
                                          • Phaedruxundefined
                                            Phaedrux Moderator @Leblond
                                            last edited by

                                            @Leblond said in Cambio elettronica:

                                            G1 H1 X0 Y0 F500 ; move quickly to X or Y endstop and stop there (first pass)
                                            G1 H1 X0 ; home X axis
                                            G1 H1 Y0 ; home Y axis

                                            You need a distance for X and Y movement. 0 is no movement.

                                            Z-Bot CoreXY Build | Thingiverse Profile

                                            Leblondundefined 2 Replies Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA