Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Cambio elettronica

    Scheduled Pinned Locked Moved
    Duet Hardware and wiring
    9
    124
    6.4k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • droftartsundefined
      droftarts administrators @Leblond
      last edited by

      @Leblond It sounds like you have connected the stepper motors to the wrong pins! See the wiring diagram here for the motor connections: https://duet3d.dozuki.com/Wiki/Duet_Wiring_Diagrams

      If your wiring is correct, post your config.g file. Also send M115 and post the response.

      Ian

      Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

      1 Reply Last reply Reply Quote 0
      • Leblondundefined
        Leblond
        last edited by

        0:/sys/config.g.bak
        ; Configuration file for Duet WiFi (firmware version 3)
        ; executed by the firmware on start-up
        ;
        ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale)

        ; General preferences
        G90 ; send absolute coordinates...
        M83 ; ...but relative extruder moves
        M550 P"X5SA PRO" ; set printer name

        M667 S1 ; select CoreXY mode

        ; Network
        M552 S1 ; enable network
        M586 P0 S1 ; enable HTTP
        M586 P1 S0 ; disable FTP
        M586 P2 S0 ; disable Telnet

        ; Drives
        M569 P0 S1 ; physical drive 0 goes forwards
        M569 P1 S0 ; physical drive 1 goes backwards
        M569 P2 S0 ; physical drive 2 goes backwards
        M569 P3 S0 ; physical drive 3 goes backwards
        M584 X0 Y1 Z2 E3 ; set drive mapping
        M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
        M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
        M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
        M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
        M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
        M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
        M84 S30 ; Set idle timeout

        ; Axis Limits
        M208 X0 Y0 Z0 S1 ; set axis minima
        M208 X330 Y330 Z400 S0 ; set axis maxima

        ; Endstops
        M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
        M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
        M574 Z1 S2 ; configure Z-probe endstop for low end on Z

        ; Z-Probe
        M558 P1 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
        G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
        M557 X60:300 Y50:300 S20 ; define mesh grid

        ; Heaters
        M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
        M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
        M143 H0 S120 ; set temperature limit for heater 0 to 120C
        M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
        M140 H0 ; map heated bed to heater 0
        M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
        M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
        M143 H1 S280 ; set temperature limit for heater 1 to 280C
        M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

        ; Fans
        M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
        M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
        M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
        M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

        ; Tools
        M563 P0 D0 H1 F0 ; define tool 0
        G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
        G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

        ; Custom settings are not defined

        ; Miscellaneous
        M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

        droftartsundefined 2 Replies Last reply Reply Quote 0
        • droftartsundefined
          droftarts administrators @Leblond
          last edited by

          @Leblond said in Cambio elettronica:

          config.g.bak

          That's the backup file. Post 'config.g'.

          Ian

          Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

          1 Reply Last reply Reply Quote 0
          • droftartsundefined
            droftarts administrators @Leblond
            last edited by

            @Leblond said in Cambio elettronica:

            M584 X0 Y1 Z2 E3

            That looks okay. Note that the order of the driver pins on the board, from left to right, is E1, E0, X, Y, Z.

            Ian

            Bed-slinger - Mini5+ WiFi/1LC | RRP Fisher v1 - D2 WiFi | Polargraph - D2 WiFi | TronXY X5S - 6HC/Roto | CNC router - 6HC | Tractus3D T1250 - D2 Eth

            1 Reply Last reply Reply Quote 0
            • Leblondundefined
              Leblond
              last edited by

              ; Configuration file for Duet WiFi (firmware version 3)
              ; executed by the firmware on start-up
              ;
              ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 13:40:08 GMT+0200 (Ora legale dell’Europa centrale)

              ; General preferences
              G90 ; send absolute coordinates...
              M83 ; ...but relative extruder moves
              M550 P"X5SA PRO" ; set printer name

              ;M667 S1 ; select CoreXY mode
              M669 K1
              ; Network
              M552 S1 ; enable network
              M586 P0 S1 ; enable HTTP
              M586 P1 S0 ; disable FTP
              M586 P2 S0 ; disable Telnet

              ; Drives
              M569 P0 S1 ; physical drive 0 goes forwards
              M569 P1 S0 ; physical drive 1 goes backwards
              M569 P2 S0 ; physical drive 2 goes backwards
              M569 P3 S0 ; physical drive 3 goes backwards
              M584 X0 Y1 Z2 E3 ; set drive mapping
              M350 X16 Y16 Z16 E16 I1 ; configure microstepping with interpolation
              M92 X80.00 Y80.00 Z4000.00 E420.00 ; set steps per mm
              M566 X900.00 Y900.00 Z12.00 E120.00 ; set maximum instantaneous speed changes (mm/min)
              M203 X6000.00 Y6000.00 Z180.00 E1200.00 ; set maximum speeds (mm/min)
              M201 X500.00 Y500.00 Z20.00 E250.00 ; set accelerations (mm/s^2)
              M906 X800 Y800 Z800 E800 I30 ; set motor currents (mA) and motor idle factor in per cent
              M84 S30 ; Set idle timeout

              ; Axis Limits
              M208 X0 Y0 Z0 S1 ; set axis minima
              M208 X330 Y330 Z400 S0 ; set axis maxima

              ; Endstops
              M574 X1 S1 P"xstop" ; configure active-high endstop for low end on X via pin xstop
              M574 Y1 S1 P"ystop" ; configure active-high endstop for low end on Y via pin ystop
              M574 Z1 S2 ; configure Z-probe endstop for low end on Z

              ; Z-Probe
              M558 P5 C"zprobe.in" H5 F120 T6000 ; set Z probe type to unmodulated and the dive height + speeds
              G31 P500 X0 Y0 Z2.5 ; set Z probe trigger value, offset and trigger height
              M557 X60:300 Y50:300 S20 ; define mesh grid

              ; Heaters
              M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
              M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
              M143 H0 S120 ; set temperature limit for heater 0 to 120C
              M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
              M140 H0 ; map heated bed to heater 0
              M308 S1 P"e0temp" Y"thermistor" T100000 B4138 ; configure sensor 1 as thermistor on pin e0temp
              M950 H1 C"e0heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
              M143 H1 S280 ; set temperature limit for heater 1 to 280C
              M307 H1 B0 S1.00 ; disable bang-bang mode for heater and set PWM limit

              ; Fans
              M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
              M106 P0 S0 H-1 ; set fan 0 value. Thermostatic control is turned off
              M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
              M106 P1 S1 H1 T45 ; set fan 1 value. Thermostatic control is turned on

              ; Tools
              M563 P0 D0 H1 F0 ; define tool 0
              G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
              G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C

              ; Custom settings are not defined

              ; Miscellaneous
              M911 S22 R23 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss

              1 Reply Last reply Reply Quote 0
              • Leblondundefined
                Leblond
                last edited by

                sicuramente e' tutto sbagliato ma l'ho fatto con il configuratore reprap

                1 Reply Last reply Reply Quote 0
                • Leblondundefined
                  Leblond
                  last edited by

                  20200331_185549.jpg

                  1 Reply Last reply Reply Quote 0
                  • Leblondundefined
                    Leblond
                    last edited by

                    l'unico problema elettrico che ho riscontrato e' il colore dei fili
                    2b rosso
                    2a blu
                    1a verde
                    1b nero

                    ma la connessione dei fili dei motori sono invertiti le fasi 1a e 1b
                    che sia quello?

                    1 Reply Last reply Reply Quote 0
                    • Leblondundefined
                      Leblond
                      last edited by

                      cioe' i cavi dei motori che dovrebbero essere 2b-R 2a-B 1a-V 1b-N sui fili 1a e 1b sono invertiti

                      1 Reply Last reply Reply Quote 0
                      • Leblondundefined
                        Leblond
                        last edited by

                        G28
                        Error: Z probe already triggered at start of probing move

                        1 Reply Last reply Reply Quote 0
                        • Leblondundefined
                          Leblond
                          last edited by

                          Ragazzi ho realmente bisogno di voi, non ce ne salto fuori, mi continua a dare come errore Z probe already triggered at start of probing move

                          1 Reply Last reply Reply Quote 0
                          • Leblondundefined
                            Leblond
                            last edited by

                            Non so come fargli cambiare stato

                            1 Reply Last reply Reply Quote 0
                            • Leblondundefined
                              Leblond
                              last edited by

                              smanettando qualcosa e' cambiato non so il perche' ma nel file home x e y invece di sondare a 0 sondava a 335
                              adesso l'errore e' cambiato dicendomi G0/G1: insufficient axes homed

                              1 Reply Last reply Reply Quote 0
                              • Phaedruxundefined
                                Phaedrux Moderator
                                last edited by

                                https://duet3d.dozuki.com/Wiki/FAQ#Section_I_get_this_error_message_Error_G0_G1_insufficient_axes_homed

                                Z-Bot CoreXY Build | Thingiverse Profile

                                Leblondundefined 1 Reply Last reply Reply Quote 0
                                • Leblondundefined
                                  Leblond @Phaedrux
                                  last edited by

                                  @Phaedrux ; homeall.g
                                  ; called to home all axes
                                  ;
                                  ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 22:19:23 GMT+0200 (Ora legale dell’Europa centrale)
                                  G91 ; relative positioning
                                  G1 H2 Z10 F3000 ; lift Z relative to current position
                                  G1 H1 X0 Y0 F500 ; move quickly to X or Y endstop and stop there (first pass)
                                  G1 H1 X0 ; home X axis
                                  G1 H1 Y0 ; home Y axis
                                  G1 X-5 Y-5 F500 ; go back a few mm
                                  G1 H1 X0 F360 ; move slowly to X axis endstop once more (second pass)
                                  G1 H1 Y0 ; then move slowly to Y axis endstop
                                  G90 ; absolute positioning
                                  G1 X60 Y50 F500 ; go to first bed probe point and home Z
                                  G30 ; home Z by probing the bed

                                  ; Uncomment the following lines to lift Z after probing
                                  ;G91 ; relative positioning
                                  ;G1 Z10 F50 ; lift Z relative to current position
                                  ;G90 ; absolute positioning

                                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                                  • Leblondundefined
                                    Leblond
                                    last edited by

                                    ; homez.g
                                    ; called to home the Z axis
                                    ;
                                    ; generated by RepRapFirmware Configuration Tool v2.1.8 on Tue Mar 31 2020 22:19:24 GMT+0200 (Ora legale dell’Europa centrale)
                                    G91 ; relative positioning
                                    G1 H2 Z-9999 F3000 ; lift Z relative to current position
                                    G90 ; absolute positioning
                                    G1 X60 Y50 F3000 ; go to first probe point
                                    G30 ; home Z by probing the bed

                                    ; Uncomment the following lines to lift Z after probing
                                    ;G91 ; relative positioning
                                    ;G1 Z10 F50 ; lift Z relative to current position
                                    ;G90 ; absolute positioning

                                    1 Reply Last reply Reply Quote 0
                                    • Leblondundefined
                                      Leblond
                                      last edited by

                                      a sembra tutto ok, ma posso anche sbagliarmi

                                      1 Reply Last reply Reply Quote 0
                                      • Leblondundefined
                                        Leblond
                                        last edited by

                                        ok ho fatto esperimento, ho mandato gli assi in home mettendo una parte mettalica sotto il sensore ma questo pur segnando 0 partendo da 1000 non si ferma

                                        1 Reply Last reply Reply Quote 0
                                        • Phaedruxundefined
                                          Phaedrux Moderator @Leblond
                                          last edited by

                                          @Leblond said in Cambio elettronica:

                                          G1 H1 X0 Y0 F500 ; move quickly to X or Y endstop and stop there (first pass)
                                          G1 H1 X0 ; home X axis
                                          G1 H1 Y0 ; home Y axis

                                          You need a distance for X and Y movement. 0 is no movement.

                                          Z-Bot CoreXY Build | Thingiverse Profile

                                          Leblondundefined 2 Replies Last reply Reply Quote 0
                                          • Leblondundefined
                                            Leblond @Phaedrux
                                            last edited by

                                            @Phaedrux ho appena appurato che il sensore funziona ma che sia innescato o meno il piatto non si ferma ho usato anche questo parametro e credo sia corretto
                                            M558 P5 C"! zprobe.in" H10 F120 T500

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA