Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    Bltouch setup need help

    Scheduled Pinned Locked Moved
    Firmware installation
    4
    93
    3.8k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • JoergS5undefined
      JoergS5 @Elvis0z
      last edited by

      @Elvis0z you will get used to it, it is not so complicated. One G-Code one line, the explanation is in https://duet3d.dozuki.com/Wiki/Gcode#main

      It's only a bit complicated with the change from RRF2 to RRF3, because several G-Codes changed with the parameter meanings. Some were deprecated, some added.

      1 Reply Last reply Reply Quote 0
      • JoergS5undefined
        JoergS5 @Elvis0z
        last edited by

        @Elvis0z I know only one method to find the reason of the error: throw out parts of the config, test M98 again, throw out next until you find the reason. Throw out will be possible only for the parts which are not essential, like the heaters, fans, tools, miscellaneous. Then Z-Probe, Axis Limits. Please make a backup first!

        1 Reply Last reply Reply Quote 0
        • Elvis0zundefined
          Elvis0z
          last edited by

          Will have a go

          JoergS5undefined 1 Reply Last reply Reply Quote 0
          • JoergS5undefined
            JoergS5 @Elvis0z
            last edited by

            @Elvis0z I forgot: the forum here is the backup.

            1 Reply Last reply Reply Quote 0
            • Elvis0zundefined
              Elvis0z
              last edited by

              Can I post a video here of what it is doing?

              JoergS5undefined 1 Reply Last reply Reply Quote 0
              • JoergS5undefined
                JoergS5 @Elvis0z
                last edited by

                @Elvis0z most people make a youtube video and post the link here. Don't know whether you can post video directly, I suspect not.

                1 Reply Last reply Reply Quote 0
                • Elvis0zundefined
                  Elvis0z
                  last edited by

                  Ok I will try That

                  1 Reply Last reply Reply Quote 0
                  • Elvis0zundefined
                    Elvis0z
                    last edited by

                    https://youtu.be/Y6CVXsrzRvk

                    Here is the video of what is happening

                    JoergS5undefined 1 Reply Last reply Reply Quote 0
                    • JoergS5undefined
                      JoergS5 @Elvis0z
                      last edited by JoergS5

                      @Elvis0z maybe its the
                      M203 X6000.00 Y6000.00 Z180.00 E6000.00
                      setting, because Z moves with maximum 3 mm/second, which will take forever at this distance on the video. Please set higher and try again.

                      PS the video was very helpful, this was a good idea!!

                      1 Reply Last reply Reply Quote 0
                      • Elvis0zundefined
                        Elvis0z
                        last edited by

                        should I put the same as x and y?

                        JoergS5undefined 1 Reply Last reply Reply Quote 0
                        • JoergS5undefined
                          JoergS5 @Elvis0z
                          last edited by JoergS5

                          @Elvis0z you have trapezoid at Z, the stepper turns 5 rotations per second, your trapezoid has 2 mm for every rotation, so 10 mm/s, the value for Z should be 600 mm/min. The stepper could run 16 rotations/s maximum, but better be on the safe side.

                          1 Reply Last reply Reply Quote 0
                          • Elvis0zundefined
                            Elvis0z
                            last edited by

                            Thanks for your help.

                            1 Reply Last reply Reply Quote 0
                            • Elvis0zundefined
                              Elvis0z
                              last edited by

                              So just to make sure I have to home z before I can do anything else?

                              JoergS5undefined 1 Reply Last reply Reply Quote 0
                              • Elvis0zundefined
                                Elvis0z
                                last edited by

                                Ahhhhh gets to the same point and deploys probe then nothing like in the video

                                JoergS5undefined 1 Reply Last reply Reply Quote 0
                                • JoergS5undefined
                                  JoergS5 @Elvis0z
                                  last edited by

                                  @Elvis0z please see above, take 600. 6000 ist too much for the stepper.

                                  1 Reply Last reply Reply Quote 0
                                  • JoergS5undefined
                                    JoergS5 @Elvis0z
                                    last edited by

                                    @Elvis0z said in Bltouch setup need help:

                                    So just to make sure I have to home z before I can do anything else?

                                    the printer want to have homed all axes before it proceeds.

                                    1 Reply Last reply Reply Quote 0
                                    • Elvis0zundefined
                                      Elvis0z
                                      last edited by

                                      G28
                                      

                                      Error: Z probe was not triggered during probing move
                                      Error: Homing failed

                                      Just keep getting this error

                                      JoergS5undefined 1 Reply Last reply Reply Quote 0
                                      • JoergS5undefined
                                        JoergS5 @Elvis0z
                                        last edited by JoergS5

                                        @Elvis0z can you make a M122 after the G28 test please and show?

                                        An does G1 Z10 and G1 Z-10 move as expected when you run this commands directly?

                                        1 Reply Last reply Reply Quote 0
                                        • Elvis0zundefined
                                          Elvis0z
                                          last edited by

                                          @JoergS5 said in Bltouch setup need help:

                                          G1 Z-10
                                          M122
                                          === Diagnostics ===
                                          RepRapFirmware for Duet 2 WiFi/Ethernet version 3.1.1 running on Duet WiFi 1.02 or later
                                          Board ID: 08DGM-9T6BU-FG3SD-6J9D0-3S86Q-1AMBF
                                          Used output buffers: 3 of 24 (10 max)
                                          === RTOS ===
                                          Static ram: 27980
                                          Dynamic ram: 93712 of which 44 recycled
                                          Exception stack ram used: 264
                                          Never used ram: 9072
                                          Tasks: NETWORK(ready,384) HEAT(blocked,1224) MAIN(running,1880) IDLE(ready,80)
                                          Owned mutexes:
                                          === Platform ===
                                          Last reset 00:00:35 ago, cause: software
                                          Last software reset at 2020-07-09 19:59, reason: User, spinning module GCodes, available RAM 8584 bytes (slot 1)
                                          Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0xffffffff Task MAIN
                                          Error status: 0
                                          MCU temperature: min 30.6, current 31.7, max 32.0
                                          Supply voltage: min 23.9, current 24.1, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
                                          Driver 0: standstill, SG min/max not available
                                          Driver 1: standstill, SG min/max not available
                                          Driver 2: standstill, SG min/max not available
                                          Driver 3: standstill, SG min/max not available
                                          Driver 4: standstill, SG min/max not available
                                          Date/time: 2020-07-09 19:59:45
                                          Cache data hit count 60372819
                                          Slowest loop: 4.74ms; fastest: 0.13ms
                                          I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
                                          === Storage ===
                                          Free file entries: 10
                                          SD card 0 detected, interface speed: 20.0MBytes/sec
                                          SD card longest read time 3.1ms, write time 0.0ms, max retries 0
                                          === Move ===
                                          Hiccups: 0(0), FreeDm: 169, MinFreeDm: 169, MaxWait: 0ms
                                          Bed compensation in use: none, comp offset 0.000
                                          === MainDDARing ===
                                          Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
                                          === AuxDDARing ===
                                          Scheduled moves: 0, completed moves: 0, StepErrors: 0, LaErrors: 0, Underruns: 0, 0 CDDA state: -1
                                          === Heat ===
                                          Bed heaters = 0 -1 -1 -1, chamberHeaters = -1 -1 -1 -1
                                          === GCodes ===
                                          Segments left: 0
                                          Movement lock held by null
                                          HTTP is idle in state(s) 0
                                          Telnet is idle in state(s) 0
                                          File is idle in state(s) 0
                                          USB is idle in state(s) 0
                                          Aux is idle in state(s) 0
                                          Trigger is idle in state(s) 0
                                          Queue is idle in state(s) 0
                                          Daemon is idle in state(s) 0
                                          Autopause is idle in state(s) 0
                                          Code queue is empty.
                                          === Network ===
                                          Slowest loop: 41.57ms; fastest: 0.00ms
                                          Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
                                          HTTP sessions: 1 of 8

                                          • WiFi -
                                            Network state is active
                                            WiFi module is connected to access point
                                            Failed messages: pending 0, notready 0, noresp 0
                                            WiFi firmware version 1.23
                                            WiFi MAC address ec:fa:bc:2d:b3:11
                                            WiFi Vcc 3.36, reset reason Unknown
                                            WiFi flash size 4194304, free heap 20056
                                            WiFi IP address 192.168.50.68
                                            WiFi signal strength -46dBm, reconnections 0, sleep mode modem
                                            Socket states: 0 0 0 0 0 0 0 0

                                          09/07/2020, 20:00:48 G1 Z10
                                          Error: G0/G1: insufficient axes homed
                                          09/07/2020, 20:01:17 G1 Z-10
                                          Error: G0/G1: insufficient axes homed

                                          1 Reply Last reply Reply Quote 0
                                          • Elvis0zundefined
                                            Elvis0z
                                            last edited by

                                            When I do a G28 command once z probe deploys the console just spins around and I can't put any commands in till I restart control board

                                            JoergS5undefined 1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA