I have been using the Duet 3 scanning z probe and the third one has an internal short. I pugged in the board to the SZP per documentation and no LED lights and didn't show up in the web control. What I did notice was the temp on the hot end probe was now 2000C. I shut the Voron down and unplugged the Z probe board. I then booted it back up and the hot end was 22.8 and active. I checked the red 3.27vdc and black ground. The plug to the probe is black, red 3.3VDC, black Can low and red can High. I am using the supplied wires from the Duet 3 1LC, The other probes were working well this one hasn't worked at all. I have contacted Fila Studer and they asked me to enter it into the forum. Attached is a picture of the setup that was working.
[link text]

The different B values where the key. I tried the probe on temp1 and it worked. The hot end tool board was 23,6°C which is now controllable. I checked the pin connectors and plugged it into Temp0 and after booting it up it works their as well. B values affect the reported temperature.

I have tried different configurations of 308 in relation to B and C values and nothing changes, the Tool temperature is reporting 2000C, My current 308 command is: M308 S1 P"121.temp0" Y"thermistor" T10000 B4725 C7.06e-8 ;

Everything else on the tool board is working but the nozzle will not heat until the temperature probe reads correctly.
I have changed the B and C values and nothing changes it is always 20000C.

The original probe was faulty and reported 2000C and -273 or disconnected. This is a brand new probe from Revo.

This is all mounted on a Voron 2.4 R2 with the Duet 3 6HC with Duet 3 1LC and Duet 3 SZP. I am at the end of my rope and thinking about scrapping all of it for a different printer.

The SZP show up in the Duet Web control, and communication looks great, the problem is with M308 is says S10 is not a valid sensor pin.

I have the X on drive 0 , Y on drive 1, Z FR on drive 2, Z RR on drive 3 and Z RL on drive 4 and z FL on drive 5. When I home the X and Y work but the Z front left and the Z rear left go up while Z rear left and Z on front right go done binding the gantry. All Kysan Ocean motors are left to right (Red, Green, Yellow, Blue) and the are all paired the same. Do I need to re-wire rear right and front left motors or am I missing something. The printer is a Voron 2.4 R2.

The config.g:

; Configuration file for RepRapFirmware on Duet 3 Main Board 6HC
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.5.8 on Mon Nov 25 2024 09:23:39 GMT-0600 (Central Standard Time)

; General
G90 ; absolute coordinates
M83 ; relative extruder moves
M550 P"Duet 3" ; set hostname

; Network
M551 P"Voron24" ; set UI password

; Accelerometers


; Smart Drivers
M569 P0.0 S1 D2 ; driver 0.0 goes forwards (X axis)
M569 P0.1 S1 D2 ; driver 0.1 goes forwards (Y axis)
M569 P0.2 S1 D2 ; driver 0.2 goes forwards (Z axis)
M569 P0.3 S1 D2 ; driver 0.3 goes forwards (Z axis)
M569 P0.4 S1 D2 ; driver 0.4 goes forwards (Z axis)
M569 P0.5 S1 D2 ; driver 0.5 goes forwards (Z axis)

; Motor Idle Current Reduction
M906 I30 ; set motor current idle factor
M84 S30 ; set motor current idle timeout

; Axes
M584 X0.0 Y0.1 Z0.2:0.3:0.4:0.5 ; set axis mapping
M350 X16 Y16 Z16 I1 ; configure microstepping with interpolation
M906 X800 Y800 Z800 ; set axis driver currents
M92 X80 Y80 Z80 ; configure steps per mm
M208 X0:350 Y0:350 Z0:300 ; set minimum and maximum axis limits
M566 X900 Y900 Z900 ; set maximum instantaneous speed changes (mm/min)
M203 X6000 Y6000 Z6000 ; set maximum speeds (mm/min)
M201 X500 Y500 Z500 ; set accelerations (mm/s^2)

; Kinematics
M669 K1 ; configure CoreXY kinematics

; Endstops
M574 X1 P"io0.in" S1 ; configure X axis endstop
M574 Y1 P"io1.in" S1 ; configure Y axis endstop


; Sensors
M308 S0 P"temp0" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermister on pins to temp0

; Heaters
M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
M307 H0 B0 S1.00 ;disable bang bang mode for the bed heater and set PWM limit
M143 H1 S320 ; Set temperature range for heater 0-320C

; Heated beds
M140 H0 ; map heated bed to heater 0


; Fans
M950 Fo C'121.out1" Q500 ;Ceate fan0 on pin 121.out1 and set frequency
M106 P0 S0 H-1 ;set fan 0 value
M950 F0 C"out7" ; create fan #0
M106 P0 S0.5 L0 X1 B0.1 ; configure fan #0
M950 F1 C"out8" ; create fan #1
M106 P1 S0.5 B0.1 H1 T0 ; configure fan #1

; Tools
M563 P0 D0 H1 F0 ; create tool #0
M568 P0 R0 S0 ; set initial tool #0 active and standby temperatures to 0C

; Miscellaneous
M501 ; load saved parameters from non-volatile memory

Re: [Duet 3 6HC + Scanning Z Probe](not connecting)
Using the Duet 3 1LC tool board and scanning Z probe, I think the board is DOA. I get no LED light. I verified I am getting 4.99VDC at the SZP board, I also verified the CanH and CanL which are black and red wires. The tool board is working to control nozzle temp, extruder motor, hear break fan, filament fan and a BTT smart filament sensor. The SZP led is bad or the board is bad.