Try making sure you have a space between the two command line switches
bmp2c-escher3d.exe myimage.bmp myimage.bin -b -c and not -b-c.
I have successfully converted a 1126kb 24 bit bmp file to a 106kb bin. My firmware bin after the binary copy is 224kb. The bmp file needs to have large blocks of colour. Too much detail will not convert successfully.
I presume you are following the instructions on github for the PanelDue firmware.
You are missing defining a pin with M950 for the servo on the the BL Touch. My config.g for a Hypercube reads -
; Z-Probe
M950 S0 C"exp.heater7" ; assign heater7 for bltouch
M558 P9 C"^zprobe.in" H5 F120 T6000 A30 S0.02 ; Set Z probe type to bltouch and the dive height + speeds
G31 P500 X28 Y0 Z0.812 ; set Z probe trigger value, offset and trigger height
M557 X45:300 Y5:295 S40 ; define mesh grid
Have a look here https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch
Glad I spotted it! Falling back on my original DOS 2 and 3 experience!
From github -
Version 3.2.11
Upgrade Notes:
This release is compatible with RepRapFirmware 3.2 or later.
Someone that knows more may correct me but I think the last 100% 2.05 compatible version was 1.24 of the PanelDue firmware
I see the same problem and only with bed temperature. Deleting cookies and the dwc settings file and trying different browsers sometimes removes the error but it has always come back...
@spirit-robotics Look at https://github.com/Duet3D/PanelDueFirmware#splash-screen - its quite easy to do.
From github -
Version 3.2.11
Upgrade Notes:
This release is compatible with RepRapFirmware 3.2 or later.
Someone that knows more may correct me but I think the last 100% 2.05 compatible version was 1.24 of the PanelDue firmware
Glad I spotted it! Falling back on my original DOS 2 and 3 experience!
Try making sure you have a space between the two command line switches
bmp2c-escher3d.exe myimage.bmp myimage.bin -b -c and not -b-c.
I have successfully converted a 1126kb 24 bit bmp file to a 106kb bin. My firmware bin after the binary copy is 224kb. The bmp file needs to have large blocks of colour. Too much detail will not convert successfully.
I presume you are following the instructions on github for the PanelDue firmware.
You are missing defining a pin with M950 for the servo on the the BL Touch. My config.g for a Hypercube reads -
; Z-Probe
M950 S0 C"exp.heater7" ; assign heater7 for bltouch
M558 P9 C"^zprobe.in" H5 F120 T6000 A30 S0.02 ; Set Z probe type to bltouch and the dive height + speeds
G31 P500 X28 Y0 Z0.812 ; set Z probe trigger value, offset and trigger height
M557 X45:300 Y5:295 S40 ; define mesh grid
Have a look here https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch
@droftarts I was right - it was simple. Thanks Ian both fans now working as expected.
Spent far too much time trying to get my hotend and partcooling fans to work on my DUET 2 so asking here for help.
My first PWM fan connection does not work (cock up when building my HEVO) so I have to assign the hotend fan to the second connector and the part cooling fan to the third.
My config.g (from the online config tool) for the fans is -
; Fans
M950 F0 C"fan1" Q500 ; create fan 0 on pin fan1 and set its frequency
M106 P0 S1 H1 T45 ; set fan 0 value. Thermostatic control is turned on
M950 F1 C"fan2" ; create fan 1 on pin fan2 and set its frequency
M106 P1 S0 H-1 ; set fan 1 value. Thermostatic control is turned off
In my 2.06 config.g I had -
; Fans
M106 P1 S1 I0 F500 H1 T45 C"HotEnd" ; Set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
M106 P2 S0 H-1 C"PrintCool" ; suggested by forum
Running M98 P"config.g" give the following -
Error: M950: Pin 'fan2' is not free
Error: M106: Fan number 1 not found
And the hotend fan then works correctly if I heat up/cool down turning on/off at 45°C
If I restart the board it fails again and does not spin up.
The part cooling fan does not respond at all to M106 P1 and give the error "Fan number 1 not found"
I'm baffled - no doubt it will be a simple error on my part but I can't find it!
Damn.... clicked too soon. The external antenna would have been nice even although I've not had any problems with the internal one in 3 different room in the house.... 