Posts made by abstraktlighting

@CaLviNx And here is a perfect example of a pompous ass errogant hater that is the reason no one should buy this product. I have other printers and even if I was born yesterday blaming the user for the inadequacies of Duets system is so typical. I like your reasoning they all suck so Duet sucks less. Great logic brainiac. lol What are you like 11yrs old. I see youre in love with your status here and being in your little club of people that paid for their board andhave it working,. So youre fine with the fact that others paid for a product that they dont have working and instead of showing how smart you are and posting a fix you run your mouth behind the anonymity of your computer. The fact is Duet the same as anyone else who'sm in the business of selling a product should have in place a system that gets every customer up and running without expecting them to deal with assholes like you who take shots from their mommies basement and only hurt sales. The customer is always right pal. Remember tat. If I feel this way and I take the time and endure the hassle of navigating through a sea of inept admins and developers that expect customers to exert an over abundance of effort in order to use their product then it goes to reason that there are a ton of others like me that will take their business somewhere else . Thats a great business model and probably the reason you live on your moms couch. If infact Duet sucks less than Bigtreetech or the others and theyre doing well for now just think how good business could be if they didnt suck at all. If they had great cshould have a

@Veti I agree with most of that however

1. thats a default for the endr3 pro. Is it correct ? does iot work? If not then it needs to. I would
   need one for basic ender3
2. I stated that it should be basic not enabling any add-ons like bl touch.
3. Put a line that says if youy motors move the opposite way up load this macro. and have a
   macro to run them backwards. and before one starts they can confirm how theyre wired
   and make the selection that fits them.
4. Its definitely impossibble to have 1 that fits all, but not impossible to have the most popular
   models covered. It may be a little work to set up but it will reduce the number of people
   seeking simple answers ansd make them feel like Duet and its people care and they bought
   a working product with basic customer service.
5. it could be more user friendly and plug and play for basic working printing. Theyre
   welcome to read alot and experiment and its nicer to do so from a control configuration
   that works. Why suffer?

Now go newby enjoy your Duet and have fun. Setting up the printer is just the beginning. Experiment, Learn new concepts, revise your understanding of temperatures, materials, retractions settings, speed etc. You have the hardware and resources to produce good prints. It can be daunting at times. If you get stuck you may need to reset and start this process over.

Duet Customer Service and the community are also willing to help.
(When seeking assistance please explain in detail the steps that you have taken. the results you expected and the results you are getting, also be prepared to provide config files and log entries if requested)

and remember your feedback about your progress will be used to improve the process where possible.
Sincerely Duet Happy printing

@droftarts Thanks for asking because it really takes the fun out of it when it doesnt work.
I think there should be a page that simply states :
For newly installed duet wifi click here. It wipes the board clean
Then has a document to download that says

1. install this on your sd card via your computer. it should
   include the config file for that printer and have only what it
   takes to initiate a print without any add-ons that arent
   standard for that printer. and 1 test model gcode file
2. insert sd card into sd card slot on Duet
3. power cycle Duet
4. Connect the Duet via usb to your computer
5. Identify com port Duet is using via device manager port com
   properties (or whatever)
6. Get Yat open Yat Open terminal on Yat if it wont open repeat
   step 5 until it opens
7. type M558 network whatever password whatever blah blah
8. type M552S0 on Yat Message should say ok LF Wifi started or
   idle
9. type M552S1 on Yat Message should say.....iP 192.168.1.??
10. confirm that the netwoprk matches the network that your
    computer is on and that you have internet access
11. open your browser and type the same IP address and hit
    enter,dwc should automatically open.
12. uplaod test model gcode file included here double click and
    hit print
13. Follow prompts for manual bed levelling if they apply
14. enjoy your Duet for additional add-ons ie BLTouch,Filament
    Sensors etc please refer to the following.

Instead of running here and there and uploading old versions and crap you dont need and asking people and posting and waiting. Also what isnt current on github might be archived so only the current versions are available on the immediate.

If someone screws up they start over.

@infiniteloop Thanks for your printer advice I appreciate THAT. As for your other advice I am thankful for the community members that helped or tried as I stated. I dont need you to advise me on what you wrongly perceived as anger, just as I wont advise you on what I may wrongly perceive as arrogance. I merely stated that I think Duet would be alot more user friendly if they had more direct clear and concise paths and procedures for trouble shooting that can be accessed without having to navigate through personalities to retrieve required assistance in a timely non-judgemental manner. I stand by my assertion that it's not a beneficial aspect for a business model. Thanks again for sticking to printer advising and steering away from psycho analyzing.

@Phaedrux ALRIGHT GREAT THANKS MAN i REALLY APPRECIATE IT!!!!

@infiniteloop Hi how you doing? I am almost good except for my z. the bracket I made for my bl touch isnt holding it in the right spot. whould you happen to know how I can get it to let me not use it and manually set Z so i could print a bracjket?

@Veti I'dnever buy anything from them again a guy helped me some today but you cant even get simple questions answered in a timely fashion. It's a terrible business model.,

@T3P3Tony whats edited?![

Trying to finally print and keep getting failure to write halfway through extremely slow upload of g-codce file 205M.

Error: Failed to write to file.
Error: Could not write upload data!

M122
=== Diagnostics ===
Used output buffers: 3 of 32 (9 max)
=== Platform ===
RepRapFirmware for Duet WiFi version 1.20beta6 running on Duet WiFi 1.0
Board ID: 08DGM-9T6BU-FG3S4-6J1FA-3S46N-9VQ7D
Static ram used: 15472
Dynamic ram used: 97016
Recycled dynamic ram: 2200
Stack ram used: 1368 current, 5044 maximum
Never used ram: 11340
Last reset 01:16:12 ago, cause: software
Last software reset reason: User, spinning module GCodes, available RAM 11324 bytes (slot 3)
Software reset code 0x0003, HFSR 0x00000000, CFSR 0x00000000, ICSR 0x00400000, BFAR 0xe000ed38, SP 0xffffffff
Error status: 0
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest block write time: 134.4ms
MCU temperature: min 23.1, current 31.3, max 31.8
Supply voltage: min 0.0, current 23.3, max 24.0, under voltage events: 0, over voltage events: 0
Driver 0: standstill
Driver 1: standstill
Driver 2: standstill
Driver 3: standstill
Driver 4: standstill
Date/time: 2019-12-03 18:37:43
Cache data hit count 4294967295
Slowest main loop (seconds): 1.102030; fastest: 0.000032
=== Move ===
MaxReps: 2, StepErrors: 0, FreeDm: 240, MinFreeDm 238, MaxWait: 3353447050ms, Underruns: 0, 0
Scheduled moves: 55, completed moves: 55
Bed compensation in use: none
Bed probe heights: 0.000 0.000 0.000 0.000 0.000
=== Heat ===
Bed heater = 0, chamber heater = -1
Heater 0 is on, I-accum = 0.0
Heater 1 is on, I-accum = 0.5
=== GCodes ===
Segments left: 0
Stack records: 3 allocated, 0 in use
Movement lock held by null
http is idle in state(s) 0
telnet is idle in state(s) 0
file is idle in state(s) 0
serial is idle in state(s) 0
aux is idle in state(s) 0
daemon is idle in state(s) 0
queue is idle in state(s) 0
autopause is idle in state(s) 0
Code queue is empty.
Network state is running
WiFi module is connected to access point
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.23
WiFi MAC address 84:f3:eb:e3:f4:28
WiFi Vcc 3.52, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 24248
WiFi IP address 192.168.1.12
WiFi signal strength -55dBm, reconnections 0, sleep mode modem
HTTP sessions: 1 of 8
Socket states: 0 2 0 0 0 0 0 0
Responder states: HTTP(1) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)

@Veti copy that

{"board":"duetwifi10","expansion_boards":[],"firmware":2.03,"standalone":true,"nvram":true,"auto_save":{"enabled":true,"save_threshold":10,"resume_threshold":11,"gcodes_to_run":"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000"},"display":{"type":0,"encoder_steps":4,"spi_frequency":2000000,"menus":[{"name":"main","value":""}],"images":[]},"geometry":{"type":"cartesian","mins":[0,0,0],"maxes":[230,210,200],"delta_radius":105.6,"homed_height":250,"low_dive_height":false,"max_carriage_travel":260,"print_radius":85,"rod_length":215,"z_min":0},"drives":[{"direction":0,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":80,"instant_dv":15,"max_speed":100,"acceleration":500,"current":800,"driver":0,"driver_v3":"0.0","endstop_pin":"xstop","endstop_type":1,"endstop_location":1},{"direction":0,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":80,"instant_dv":15,"max_speed":100,"acceleration":500,"current":800,"driver":1,"driver_v3":"0.1","endstop_pin":"ystop","endstop_type":1,"endstop_location":1},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":4000,"instant_dv":0.2,"max_speed":3,"acceleration":20,"current":800,"driver":2,"driver_v3":"0.2","endstop_pin":null,"endstop":null,"endstop_type":0,"endstop_location":1},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":420,"instant_dv":2,"max_speed":20,"acceleration":250,"current":800,"driver":3,"driver_v3":"0.3"},{"direction":1,"microstepping":16,"microstepping_interpolation":true,"steps_per_mm":420,"instant_dv":2,"max_speed":20,"acceleration":250,"current":800,"driver":4,"driver_v3":"0.3"}],"idle":{"used":true,"factor":30,"timeout":30},"homing_speed_fast":30,"homing_speed_slow":6,"travel_speed":100,"z_dive_height":5,"slow_homing":false,"probe":{"type":"unmodulated","recovery_time":0.4,"trigger_height":2.5,"trigger_value":500,"x_offset":0,"y_offset":0,"speed":2,"deploy":false,"points":[],"pwm_channel":3,"pwm_inverted":true,"pwm_pin":null,"input_pin":"zprobe.in","modulation_pin":"zprobe.mod"},"bed_is_nozzle":true,"bed":{"present":true,"use_pid":false,"heater":2},"chamber":{"present":false,"use_pid":false,"heater":2},"heaters":[{"temp_limit":120,"scale_factor":100,"series":4700,"thermistor":100000,"beta":4138,"c":0,"channel":0,"sensor":0,"output_pin":"bedheat","sensor_type":"thermistor","sensor_pin":"bedtemp"},null,{"temp_limit":120,"scale_factor":100,"series":4700,"thermistor":100000,"beta":4138,"a":0.0005717725,"b":0.0002416626,"c":0,"channel":2,"sensor":0,"output_pin":null,"sensor_type":null,"sensor_pin":null}],"num_nozzles":1,"toolchange_wait_for_temperatures":false,"generate_t_code":false,"tools":[{"mix_ratio":[],"number":0,"name":"","extruders":[0],"heaters":[],"fans":[0],"x_offset":0,"y_offset":0,"z_offset":0}],"compensation_x_offset":15,"compensation_y_offset":15,"peripheral_points":3,"halfway_points":3,"calibration_factors":6,"probe_radius":85,"mesh":{"x_min":15,"x_max":215,"y_min":15,"y_max":195,"radius":85,"spacing":20},"home_first":false,"orthogonal":{"compensation":false,"height":50,"deviations":[0,0,0]},"network":{"enabled":true,"mac_address":"","name":"My Printer","password":"","ssid":"","ssid_password":"","dhcp":true,"ip":"192.168.1.20","netmask":"255.255.255.0","gateway":"192.168.1.254","protocols":{"http":true,"ftp":false,"telnet":false}},"fans":[{"name":"","value":0,"inverted":false,"frequency":500,"thermostatic":false,"heaters":[],"trigger_temperature":45,"output_pin":"fan0"},{"name":"","value":100,"inverted":false,"frequency":500,"thermostatic":false,"heaters":[1,0],"trigger_temperature":45,"output_pin":"fan1"},{"name":"","value":100,"inverted":false,"frequency":500,"thermostatic":false,"heaters":[1,0],"trigger_temperature":45,"output_pin":"fan1"}],"custom_settings":""}

@dc42 Hey How you doing? This thing is still crazy I cant get any cionfigs to work they all travel too far . and say the heaters are faulting. I'm going to pull this card and bl touch and put arduino back in or smash it to peices if Icant get it working .Can you look at it Please.Ive spent another 10hrs f'ing with it today. I'm beat. My names Jeff. I went through Pheadreuxs guide twice now,

@dc42 Hey Man How you doing? This thing is still crazy I cant get any cionfigs to work they all travel too far . and say the heaters are faulting. I'm going to pull this card and bl touch and put arduino back in or smash it to peices if Icant get it working .Can you look at it Please.Ive spent another 10hrs f'ing with it today. I'm beat. My names Jeff. I went through Pheadreuxs guide twice now,

@dc42 im good droftarts is helping me

@abstraktlighting that webcntrolfile on sd card in www didnt work to open web control
and theres no file "here" called config

@blt3dp theres 8.zip assets

@blt3dp yes I understand and want to dothat but theres nothing there called config?

@droftarts no config file found m503