Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login
    1. Home
    2. cabal2000
    3. Posts
    • Profile
    • Following 1
    • Followers 0
    • Topics 15
    • Posts 74
    • Best 0
    • Controversial 1
    • Groups 0

    Posts made by cabal2000

    • RE: Stepper Motor Voltage?

      @dc42 Thanks brother!!

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • Stepper Motor Voltage?

      Presently running a Maestro on 12 volts. Looking to replace the present 1.8 degree stepper motors with 0.9 degree motors. I do know that the board does have a max amp current of 1.68amps. What should I be looking for when it comes to voltage? There are so many different stepper motors voltages to choose from.

      Thanks guys

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Print stops!! Maestro 3.1.1

      @Phaedrux can do!!

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Print stops!! Maestro 3.1.1

      I'm going to reinstall everything to factory setting later today. Format the card and do a fresh install.

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Print stops!! Maestro 3.1.1

      Not that I can see. And I have been watching the board temp, its doesn't go above 35-40c, and i do have fans directed to the steppers.

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Print stops!! Maestro 3.1.1

      Supply voltage: min 0.0, current 12.2, max 12.3, under voltage events: 0, over voltage events: 0, power good: yes
      Driver 0: position 0, standstill, read errors 0, write errors 1, ifcnt 67, reads 58841, writes 6, timeouts 0, DMA errors 0
      Driver 1: position 0, standstill, read errors 0, write errors 1, ifcnt 67, reads 58841, writes 6, timeouts 0, DMA errors 0
      Driver 2: position 0, standstill, read errors 0, write errors 1, ifcnt 67, reads 58841, writes 6, timeouts 0, DMA errors 0
      Driver 3: position 0, standstill, read errors 0, write errors 1, ifcnt 69, reads 58841, writes 6, timeouts 0, DMA errors 0
      Driver 4: position 0, standstill, read errors 0, write errors 1, ifcnt 62, reads 58841, writes 6, timeouts 0, DMA errors 0

      Write errors1??? What does this mean in english?!

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • Print stops!! Maestro 3.1.1

      Morning peeps.

      I have had this issue for a few weeks now, my Maestro 3.1.1 stops part way threw a print. Is there a log file that I can look at to see there are errors? I checked in the "Console" but no errors are showing in there. It seems to be with larger print files. I'm using Simplify3D as my slicer, never had issues with it before. Yesterday I changed the MicroSD card, formatted and copied the files over and it still happened. Checked all the cables to make sure nothing was loose. Any ideas?

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Temperature rising much more slowly than the expected 1.3°C/sec?

      @Phaedrux Thanks brother, that is exactly what I've been looking for. Stay safe man!!

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Temperature rising much more slowly than the expected 1.3°C/sec?

      @Phaedrux PID tune. OK. How do I do that? Any tutorials around?

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Temperature rising much more slowly than the expected 1.3°C/sec?

      Sorry 3.1.1

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • Temperature rising much more slowly than the expected 1.3°C/sec?

      Hi guys. Maestro 3.30 firmware.
      I had a big heat bed plate about 330x330 and 5mm thick. I work out of my heated shed but it can get a little colder inside this time of the year. I keep get this error.

      Error: Heater 0 fault: temperature rising much more slowly than the expected 1.3°C/sec

      How can i get around this? It a big thick plate so I do understand the it take longer to heat up!

      Thanks Guys

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Duet 3 Mini 5+ : Initial announcement

      @Veti How do I get an invite to the pre-order?

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Maestro SD Pinout?

      @Veti understood

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Maestro SD Pinout?

      The micro usb port!! Can you not transfer file through it? Maybe user, micro usb to USB. humm

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Maestro SD Pinout?

      @Veti may have to. But right now it just a thought!!

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • Maestro SD Pinout?

      Hi guys. Is the SD port/pinout the same as whats on a PC mother board? The reason I am asking is to mod the port to accept a USB 2.0 thumb drive rather than a SD card. Just a thought.

      posted in Duet Hardware and wiring
      cabal2000undefined
      cabal2000
    • RE: Duet 3 Mini 5+ : Initial announcement

      @T3P3Tony Thanks for the quick reply Tony. Appreciate it. Take care!!

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Duet 3 Mini 5+ : Initial announcement

      @dc42 Any news? ETA? Thanks man..

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Duet 3 Mini 5+ : Initial announcement

      @antlestxp Nope, I am with you brother!! can't wait.

      posted in General Discussion
      cabal2000undefined
      cabal2000
    • RE: Duet 3 Mini 5+ : Initial announcement

      @dc42 Sounds great!! Any news on beta testing?

      posted in General Discussion
      cabal2000undefined
      cabal2000