what else is needed this is most frustrating

@phaedrux

this one has been doing this for some time though it was wireing but I have rewired it a few times

here is the M122

M122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.0 (2022-03-15 18:58:31) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P6M2-NWNS4-7JKF0-3S46J-KV0VM
Used output buffers: 3 of 24 (12 max)
=== RTOS ===
Static ram: 23868
Dynamic ram: 74860 of which 0 recycled
Never used RAM 13352, free system stack 184 words
Tasks: NETWORK(ready,129.4%,226) HEAT(notifyWait,2.2%,332) Move(notifyWait,0.1%,364) MAIN(running,147.8%,448) IDLE(ready,1.3%,30), total 280.8%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 27:25:41 ago, cause: software
Last software reset at 2022-05-03 13:49, reason: User, GCodes spinning, available RAM 13208, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Step timer max interval 0
MCU temperature: min 35.2, current 36.3, max 37.7
Supply voltage: min 24.1, current 24.3, max 24.4, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2022-05-04 17:15:28
Cache data hit count 4294967295
Slowest loop: 33.88ms; fastest: 0.19ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 26.5ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 15.40ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions
HTTP sessions: 1 of 8
- WiFi -
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.26
WiFi MAC address 98:cd:ac:20:60:d8
WiFi Vcc 3.45, reset reason Power up
WiFi flash size 4194304, free heap 25352
WiFi IP address 192.168.1.31
WiFi signal strength -66dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0```

and the M98 P

M98 P"config.g"
HTTP is enabled on port 80
FTP is disabled
TELNET is disabled

@oliof duh!!!!

thank seems to have fixed printer #2 thank you

I have 2 printers doing strange things after finishing or canceling a print and starting the next print.

printer 1 will not deploy BLtouch until the printer is rebooted.... if I deploy the test probe, then hit the emergency stop the probe will deploy prior to stopping and resetting.

printer 2 finishes the print when I start the next it homes all axis then goes slightly left and lifts Z pushed plastic then moved to X Y home and pushes plastic to fast while raising Z I hit emergency stop and print the same file with no issues.

@maestro very nice looking work.

someday ill go through mine and clean it up a bit more.

20210326_230625844_iOS.heic 20220118_130542466_iOS.heic 20220114_231353954_iOS.heic 20220113_201749533_iOS.heic

@mrehorstdmd thank you but I already have the motor just trying to find out how to properly wire in some shotkey diode as @dc42 has mentions in other posts

So I am building a printer and the Z is moved by a belt looking into breaking options ( I see that break control was added in the latest beta but I had already order hardware)

I saw DC_42 say to use 8 shotkey diodes and wondering how to wire them up to clamp the stepper in place when powered off… looking on here and google I’m a little lost on property setting this up. Any one have a quick wire diagram of how to accomplish this please.

@Phaedrux thank you very much

Fan timer how to set one up? I am wondering if there is a End code command I can use to run my cabinet fan for a bit after print...

A; Set it up for a set time like 5 min or so
B; Set it to bed or chamber thermistor

I know you can set it to run thermally controlled but when printing abs and other high temp filament I would set that in start Gcode like M106 P2 S100 .. but at the end is would like it to run a cool down so like M106 P2 S255 (5min) (chamber temp 30) (bed temp 30)

seem to be working now thanks for the help