Navigation

    Duet3D Logo

    Duet3D

    • Register
    • Login
    • Search
    • Categories
    • Tags
    • Documentation
    • Order
    1. Home
    2. Dav
    • Profile
    • Following
    • Followers
    • Topics
    • Posts
    • Best
    • Groups

    Dav

    @Dav

    0
    Reputation
    44
    Posts
    1
    Profile views
    0
    Followers
    0
    Following
    Joined Last Online

    Dav Follow

    Best posts made by Dav

    This user hasn't posted anything yet.

    Latest posts made by Dav

    • RE: Duet Wifi + Raspberry Octoprint Power Problem

      @bearer Yes I use octoprint only to print in connected mode with palette2, on my octoprint I have duet and palette connected

      posted in Duet Hardware and wiring
      Dav
      Dav
    • RE: Duet Wifi + Raspberry Octoprint Power Problem

      @bearer
      On duet I have 2.0.7, and on palette the latest

      posted in Duet Hardware and wiring
      Dav
      Dav
    • RE: Duet Wifi + Raspberry Octoprint Power Problem

      I tried the command but it disconnect all ports and i'm not able to see devices.

      posted in Duet Hardware and wiring
      Dav
      Dav
    • Duet Wifi + Raspberry Octoprint Power Problem

      Hi
      I connected today my duet to my octoprint to use my Palette in connected mode but if the printer is off and the raspberry is on I see the bltouch on and the paneldue blinking, why?
      How can I fix this problem?

      posted in Duet Hardware and wiring
      Dav
      Dav
    • RE: Stringing problem corexy

      @deckingman

      it's a direct, I have less than 10cm of bowden tube between bmg and hotend

      posted in Example setups and prints
      Dav
      Dav
    • Stringing problem corexy

      Hi

      As you can see in the picture I have problemswith my direct BMG corexy, these are my config:

      019a2f10-053f-4922-9382-c55e8e94c78d-image.png

      WhatsApp Image 2020-03-17 at 14.01.28.jpeg

      posted in Example setups and prints
      Dav
      Dav
    • BLTouch extend problem

      Hi

      I wired and configured on a duet wifi a new bltouch original, I'm able to do self test, I'm able to extend and retract it but I read this:

      If all is well the web interface should report a value of ”0” in the Z probe column when the pin is extended. You can then lightly touch the extended probe pin to check that the pin retracts, the value in the Z probe Column should change to “1000”

      My bltouch value 0 is when is retract and 1000 if I try to touch.

      I'm trying to do M30 to make first configuration, the bltouch pin extend but when touch the bed it start blinking.

      My conf is:

      ; Axis Limits
      M208 X0 Y0 Z0 S1 ; set axis minima
      M208 X300 Y300 Z350 S0 ; set axis maxima

      ; Endstops
      ;M574 X1 Y1 Z2 S1 ; set active high and disabled endstops
      M574 X1 Y2 S0 ; set active high and disabled endstops
      M574 Z1 S2 ; set endstops controlled by probe

      ; Z-Probe
      M307 H3 A-1 C-1 D-1 ; disable heater on PWM channel for BLTouch
      M558 P9 H5 F100 T2000 ; set Z probe type to bltouch and the dive height + speeds
      G31 X0 Y-36 Z0.3 P25 ; set Z probe trigger value, offset and trigger height
      M557 X60:215 Y60:215 S40 ; define mesh grid

      Thanks

      posted in General Discussion
      Dav
      Dav
    • RE: M593 Dynamic Acceleration Adjustment no effect

      @bot how?

      posted in Tuning and tweaking
      Dav
      Dav
    • RE: M593 Dynamic Acceleration Adjustment no effect

      Hi
      I calculate my hz but where I've to put the m593 command inside the conf.g?

      posted in Tuning and tweaking
      Dav
      Dav
    • RE: Stepper motor noise

      @deckingman hi
      Today I received new stepper motors for another printer, I tried to install them:

      Technical info:
      -Manufacturer: LDO
      -Model: LDO-42STH47
      -Holding Torque: 5.5 kg/cm - 76oz-in
      -Shaft: 5mm
      -Voltage rating: 3.1V
      -Stepping angle:1.8 degrees
      -Current rating: 2.5A/Phase
      -Connector type: JST PH-6

      So I see max current 2.5, what's the right current? Right now with same configuration of 800 print better than other motors but I hear a little noise and vibration.

      posted in Duet Hardware and wiring
      Dav
      Dav