Posts made by IndeX4D

Hello duet friends,
I don't use my duet 3 mini, so I want to make it work for something else.
I would like it as my home grow Computer:D
Is it possible to adjust a timer. Like I want move an axis to a specific time.
And is it possible to connect a pH sensor? Or maybe a electrical trigger...
Thanks a lot

@Phaedrux

Edit: sorry, I haven´t seen your post. Still a case of warranty?
thanks

While DWC is ´´disconnectedt´´ , I could make a M122.
Strangely, after reflashing the image, the printer is starting quiet normal till the first prompts```
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.5.1 (2024-04-19 14:30:55) running on Duet 3 MB6HC v1.02 or later (SBC mode)
Board ID: 08DLM-9K6R1-L83T8-6J1F6-3S46P-1FJTN
Used output buffers: 1 of 40 (2 max)
=== RTOS ===
Static ram: 155208
Dynamic ram: 85688 of which 0 recycled
Never used RAM 105096, free system stack 204 words
Tasks: SBC(2,ready,0.3%,652) HEAT(3,nWait 6,0.0%,363) Move(4,nWait 6,0.0%,336) CanReceiv(6,nWait 1,0.0%,797) CanSender(5,nWait 7,0.0%,334) CanClock(7,delaying,0.0%,351) TMC(4,nWait 6,9.0%,56) MAIN(2,running,90.3%,444) IDLE(0,ready,0.4%,30), total 100.0%
Owned mutexes: HTTP(MAIN)
=== Platform ===
Last reset 00:00:33 ago, cause: power up
Last software reset at 2024-05-03 21:13, reason: User, Gcodes spinning, available RAM 94648, slot 0
Software reset code 0x6003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task SBC Freestk 0 n/a
Error status: 0x00
MCU temperature: min 43.3, current 44.3, max 44.3
Supply voltage: min 24.1, current 24.2, max 24.2, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 12.2, current 12.3, max 12.4, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a, mspos 8, reads 51700, writes 11 timeouts 0
Driver 1: standstill, SG min n/a, mspos 8, reads 51701, writes 11 timeouts 0
Driver 2: standstill, SG min n/a, mspos 8, reads 51701, writes 11 timeouts 0
Driver 3: standstill, SG min n/a, mspos 8, reads 51701, writes 11 timeouts 0
Driver 4: standstill, SG min n/a, mspos 8, reads 51701, writes 11 timeouts 0
Driver 5: standstill, SG min n/a, mspos 8, reads 51701, writes 11 timeouts 0
Date/time: 1970-01-01 00:00:00
Slowest loop: 0.21ms; fastest: 0.06ms
=== Storage ===
Free file entries: 20
SD card 0 not detected, interface speed: 37.5MBytes/sec
SD card longest read time 0.0ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, height map offset 0.000, max steps late 0, min interval 0, bad calcs 0, ebfmin 0.00, ebfmax 0.00
no step interrupt scheduled
Moves shaped first try 0, on retry 0, too short 0, wrong shape 0, maybepossible 0
=== DDARing 0 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== DDARing 1 ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
=== GCodes ===
Movement locks held by null, null
HTTP* is doing "M122" in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
File2 is idle in state(s) 0
Queue2 is idle in state(s) 0
Q0 segments left 0, axes/extruders owned 0x0000000
Code queue 0 is empty
Q1 segments left 0, axes/extruders owned 0x0000000
Code queue 1 is empty
=== CAN ===
Messages queued 166, received 928, lost 0, errs 1, boc 0
Longest wait 0ms for reply type 0, peak Tx sync delay 68, free buffers 50 (min 50), ts 166/165/0
Tx timeouts 0,0,0,0,0,0
=== SBC interface ===
Transfer state: 5, failed transfers: 1, checksum errors: 4
RX/TX seq numbers: 1389/1303
SPI underruns 3, overruns 3
State: 5, disconnects: 0, timeouts: 0 total, 0 by SBC, IAP RAM available 0x253c0
Buffer RX/TX: 0/0-0, open files: 0
=== Duet Control Server ===
Duet Control Server version 3.5.1 (2024-04-19 16:23:47, 64-bit)
HTTP+Executed:

Executing M122
Trigger:
Buffered code: M950 H0 C"out0" T0 ; create bed heater output on out0 and map it to sensor 0
Buffered code: M140 H0
Buffered code: M307 H0 R0.468 K0.275:0.000 D19.70 E1.35 S1.00 B0 ; disable bang-bang mode for the bed heater and set PWM limit
Buffered code: M143 H0 S120
Buffered code: M308 S1 P"temp1" Y"pt1000" T100000 B4138 ; configure sensor 1 as PT1000 on pin 121.temp0
Buffered code: M950 H1 C"out1" T1 ; create nozzle heater output on out1 and map it to sensor 1
Buffered code: M307 H1 R6.672 K0.682:0.000 D2.57 E1.35 S1.00 B0 V23.3 ; disable bang-bang mode for heater and set PWM limit
Buffered code: M143 H1 S260
Buffered codes: 480 bytes total

Doing macro config.g, started by system
Code buffer space: 4096
Configured SPI speed: 8000000Hz, TfrRdy pin glitches: 0
Full transfers per second: 7.54, max time between full transfers: 771.1ms, max pin wait times: 257.0ms/499.8ms
Codes per second: 0.98
Maximum length of RX/TX data transfers: 3284/808

@Phaedrux When I try to connect with YAT .,.... not possible.

@chrishamm
I used a different (and working on other printer) Raspberry, cable for power the pi, Ribbon Cable, 3 different sd cards.
No change.... I also used the updatet version of duetPi and the older ones which came out in january ( the experimental boomwork). Can you please tell me which I should use? Raspberry pi 5....

ESD? The backside of the duet 6HC looks fine. Or where should i look. I also recognized, that after long power OFF, the printer is resetting in a slower way and one time I could home.
But when I want to make a prompt, it gets worst.

I´m going to print in standalone mode, now. I´ll report.

I got my board a few weeks ago from Dold-Mechatronik.com

@Phaedrux
sadly the board is even restart so often that I can´t make any promps. it´s restarting very often....
I try to print in standalone mode, now.

@chrishamm did it work?

@curieos
Gotta run it?

hello all together,
I installed a smaller printer with sbc and a new duet3 6 hc.

This warning appears all the time - I changed already the raspberry pi from 5 to 3a+ and I used 3 different sd cards.
Is the board broken???
Crazy is: I printed 2 hours to test and then I switched off... next day I couldn´t even home my axis.
Everything I do comes to an lost SPI connecting.
My 2 other printers are running nicely....

@IndeX4D is ths forum still the right place for questions?

@chrishamm said in New experimental DuetPi Bookworm builds available:

/opt/dsf/conf/config.json

was alreasy on gpiochip4, strange...

@chrishamm
I don´t understand why I could printing yesterday and now it´s freaking out.

I have the pi5 and the image flashed from above. qithout arm version..
Duet 6hc and expansions 1hcl 2x + 1lc

@oozeBot
hey. Can you just shortly explain how to change the gpiochip 0 to 4?
I couldn´t manage it with the docu.
Would be great, thanks

@oliof thanks a lot!
I think we need to have a digital option for our project. It's more about industrial 3d printing in big format.
Looks like nobody cares tamv at the moment, right?
Or did they move away from github...?
Thanks

Hello duet Community
I'm planning to upgrade my tool changers and I would love to make the offsets automatically. Is somebody still using TAMV?
Or is there an other option?
-- Payed support -- possible

Thanks
R.Gruna
Index4D

Is TAMV still working?

Hello all together

Is somebody using TAMV at the moment? Or is there any other options for automatic tool offsets?
I want to reactivate different tools and I would love to make it automatic.

Thanks a lot

R Gruna

@chrishamm
ok thanks for your answer.
I just startefd in this topic and a friend is the python guy.
I need some time to understand your answer.

I did not say, that I use 3.5beta 4... is that a problem?