Posts made by SilviuZ

@t3p3tony thank you for your reply. I will use a mofset

@pcr yes it's a option... but I was wondering about the limitations of the toolboard

Hello everyone.
I have a mosquito magnum+ and I am wondering if it is possible to change the heaters ( slice engineering 2 × 50w) with 2× 65w E3D high temperature heaters.
I know that I will be just over 5A.
There is any margin up to 5.5A?
Ps. I am running 30v

@t3p3tony thank you. I bought a replacement and nothing else was damaged.

@t3p3tony ive printed a vase for 4 hours. Then i done some cleaning and weekly maintenance of the printer. I started the printer and tried to home all and the BlTouch extended the pin but no Z homing.
Flir one doesn't like close images and it's not possible to align the image correctly.
I noticed that spot on the driver and I didn't believe that could be damaged. My bad.
There is no way to save this board. Correct?

@t3p3tony I've used the board for around 500 hours of printing without any hardware change. It was perfect. And the printer was going up to 450mm/s.
It didn't had any possible short 5v/30v to the ground
the printer head is not conductive and I've used the plastic washers. Something weird happened.

@t3p3tony
thank you for the reply
I unplugged everything and still same problem

Re: Faulty Toolboard 1LC V1.1?
Hi.
I've updated my printer to RepRapFirmware for Duet 3 MB6HC version 3.4.0beta6
everything worked perfect up to one point when I didn't have any readings from extruder thermistor and the BlTouch didn't deploy anymore. I used my Flir camera and i noticed that there is a 100degrees Celsius hot spot on the tool board.
there is anything that I can do?

image url)

11/21/2021, 5:31:36 PM M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta6 (2021-11-06 11:38:57) running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S8-6JTD6-3SS6L-KA16H
Used output buffers: 6 of 40 (20 max)
=== RTOS ===
Static ram: 151136
Dynamic ram: 96484 of which 0 recycled
Never used RAM 103052, free system stack 202 words
Tasks: NETWORK(ready,27.3%,235) ETHERNET(notifyWait,0.1%,176) HEAT(notifyWait,0.0%,326) Move(notifyWait,0.0%,352) CanReceiv(notifyWait,0.0%,903) CanSender(notifyWait,0.0%,373) CanClock(delaying,0.0%,334) TMC(notifyWait,7.3%,92) MAIN(running,65.1%,1115) IDLE(ready,0.0%,30), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:03:53 ago, cause: power up
Last software reset at 2021-11-21 16:21, reason: User, GCodes spinning, available RAM 103264, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 128
MCU temperature: min 26.5, current 43.0, max 43.1
Supply voltage: min 29.3, current 29.3, max 29.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.9, current 12.1, max 12.7, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: pos 0, standstill, SG min 0, mspos 0, reads 65327, writes 14 timeouts 0
Driver 1: pos 0, standstill, SG min 0, mspos 0, reads 65327, writes 14 timeouts 0
Driver 2: pos 0, standstill, SG min 0, mspos 0, reads 65328, writes 14 timeouts 0
Driver 3: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Driver 4: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Driver 5: pos 0, standstill, SG min 0, mspos 8, reads 65331, writes 11 timeouts 0
Date/time: 2021-11-21 17:31:34
Slowest loop: 128.47ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.7ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 125, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamber heaters 2 -1 -1 -1, ordering errs 0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 2118, received 30, lost 0, longest wait 2ms for reply type 6049, peak Tx sync delay 15213, free buffers 49 (min 48), ts 1170/10/0
Tx timeouts 0,0,1159,0,0,927 last cancelled message type 4514 dest 127
=== Network ===
Slowest loop: 6.60ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• Ethernet -
  State: active
  Error counts: 0 0 1 0 0
  Socket states: 5 2 2 2 2 0 0 0

something that can generate multiple auto tuning algorithms similar with below to find the perfect input shaping values in type, hz and damping values

0-ei3-dba218c3 1633266073427 1000 1356 0 ei3 25 0.1 800
1-ei3-dba218c3 1633266078416 1000 1356 0 ei3 26 0.1 800
2-ei3-dba218c3 1633266083309 1000 1353 0 ei3 27 0.1 800
3-ei3-dba218c3 1633266088439 1000 1361 0 ei3 28 0.1 800
4-ei3-dba218c3 1633266093576 1000 1357 0 ei3 29 0.1 800
5-ei3-dba218c3 1633266098567 1000 1356 0 ei3 30 0.1 800
6-ei3-dba218c3 1633266103563 1000 1366 0 ei3 31 0.1 800
7-ei3-dba218c3 1633266108571 1000 1356 0 ei3 32 0.1 800
8-ei3-dba218c3 1633266113494 1000 1356 0 ei3 33 0.1 800
9-ei3-dba218c3 1633266118404 1000 1359 0 ei3 34 0.1 800
10-ei3-dba218c3 1633266123400 1000 1363 0 ei3 35 0.1 800
11-ei3-dba218c3 1633266128449 1000 1356 0 ei3 36 0.1 800
12-ei3-dba218c3 1633266133376 1000 1356 0 ei3 37 0.1 800
13-ei3-dba218c3 1633266138590 1000 1363 0 ei3 38 0.1 800
14-ei3-dba218c3 1633266143640 1000 1359 0 ei3 39 0.1 800
15-ei3-dba218c3 1633266148722 1000 1353 0 ei3 40 0.1 800

@mfs12 hi!
I've tested the plugin and its working nice.
can I suggest to have a automatic ringing test going trough the range 15-150 HZ with the option of changing in between NONE, ZVD, ZVDD EI2, EI3, minimum acceleration and the damping factor.
Thank you

@skrotz I have a similar problem.
With imput shaper " none" and PA 0.04 I get cube with perfect corners.
Any other input shaper I get artifacts just before the corner like a under extrusion ( a 5-10mm concave surface) and at the most pointy area it is looking like over extrusion.

@dc42 Thank you for your reply.
I've tried 41HZ without a significant success.
After a couple of ringhing towers I found that indeed "ei3" it's doing the best cancellation at 28HZ.
I hope that in the future if it's possible..... to have implemented a automatic axis tuning similar like the Teknic Clearpath.
Thank you again for your help.

@sebkritikel
Thank you! I will try to implement your recommendations
image url)

@dc42 Hello
After using the bellow commands I get those results:
There is any chance that the accelerometer data can be interpreted in a way that can be implemented with input shaping considering that X and Y ring in a total different way?
I am running RRF 3.4 Beta2 on a Duet 3 MB6HC and 1LC V1.1 . The printer axis are Cartesian and quite heavy ( Stratasys FDM 2000 ) but extremely rigid.
Thank you.
G1 X-50 G4 S2 G4 P10 G1 X100 F20000 M400 M956 P121.0 S1000 A0 F"AsseX.csv"
G1 Y-50 G4 S2 G4 P10 G1 Y100 F20000 M400 M956 P121.0 S1000 A0 F"AsseY.csv"
image url)
M122
=== Diagnostics ===
RepRapFirmware for Duet 3 MB6HC version 3.4.0beta2 (2021-08-03 12:42:33) running on Duet 3 MB6HC v0.6 or 1.0 (standalone mode)
Board ID: 08DJM-956L2-G43S8-6JTD6-3SS6L-KA16H
Used output buffers: 3 of 40 (20 max)
=== RTOS ===
Static ram: 151128
Dynamic ram: 93032 of which 0 recycled
Never used RAM 106440, free system stack 152 words
Tasks: NETWORK(ready,29.2%,230) ETHERNET(notifyWait,0.1%,176) HEAT(delaying,0.0%,326) Move(notifyWait,0.0%,280) CanReceiv(notifyWait,0.0%,773) CanSender(notifyWait,0.0%,373) CanClock(delaying,0.0%,340) TMC(notifyWait,9.0%,59) MAIN(running,61.7%,1118) IDLE(ready,0.0%,29), total 100.0%
Owned mutexes:
=== Platform ===
Last reset 00:32:37 ago, cause: software
Last software reset at 2021-08-05 17:55, reason: User, GCodes spinning, available RAM 106104, slot 0
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x00400000 BFAR 0x00000000 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 736
MCU temperature: min 43.5, current 44.5, max 45.2
Supply voltage: min 29.2, current 29.3, max 29.4, under voltage events: 0, over voltage events: 0, power good: yes
12V rail voltage: min 11.8, current 12.1, max 12.6, under voltage events: 0
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Driver 0: position 126480, standstill, reads 62138, writes 22 timeouts 0, SG min/max 0/1023
Driver 1: position 126480, standstill, reads 62138, writes 22 timeouts 0, SG min/max 0/1023
Driver 2: position 0, standstill, reads 62143, writes 17 timeouts 0, SG min/max 0/784
Driver 3: position 0, standstill, reads 62150, writes 11 timeouts 0, SG min/max 0/0
Driver 4: position 0, standstill, reads 62150, writes 11 timeouts 0, SG min/max 0/0
Driver 5: position 0, standstill, reads 62150, writes 11 timeouts 0, SG min/max 0/0
Date/time: 2021-08-05 18:27:59
Slowest loop: 124.51ms; fastest: 0.05ms
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 25.0MBytes/sec
SD card longest read time 0.8ms, write time 3.1ms, max retries 0
=== Move ===
DMs created 125, segments created 3, maxWait 25575ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 18, completed moves 18, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed moves 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters = 0 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1 -1, chamberHeaters = 2 -1 -1 -1
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
SBC is idle in state(s) 0
Daemon is idle in state(s) 0
Aux2 is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== CAN ===
Messages queued 17640, received 15810, lost 0, longest wait 2ms for reply type 6049, peak Tx sync delay 301, free buffers 49 (min 48), ts 9790/9789/0
Tx timeouts 0,0,0,0,0,0
=== Network ===
Slowest loop: 17.10ms; fastest: 0.02ms
Responder states: HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0), 0 sessions Telnet(0), 0 sessions
HTTP sessions: 1 of 8

• Ethernet -
  State: active
  Error counts: 0 0 0 0 0
  Socket states: 5 2 2 2 2 0 0 0

Hi, I have a heavy modified Stratasys Fdm 2000 I use Duet3 6HC main board and it's working beautifully. But I want to swap my X,Y,Z stepper motors with integrated servo motors ( Teknic Clearpath ) due to quite powerful noise for a long print during late hours ( X and Y have 4.6A stepper motors).
I would appreciate if will be developed a external driver expansion board with 3 channels with step and direction output for Duet3 6HC.
Thank you

@jens55 I'm quite sure that the centre of the processor start to " melt"

@bearer Hi, after ~10 seconds of USB power only the SAM4 go up to 60°C and raising.

i was wiring the part cooling fan and i wire get loose and hit something on the PCB.
The BL touch start like I've just powered the printer. The WiFi connection disappear, on the Panel due 7i i have "Connecting "... but nothing happen. I've connected the board to PC via USB ... no port it's working. The SD card it's working fine.
The Main processor it' getting quite hot and all the end-stop red led are on.
I've tried to erase the board, remove everything without success. Any ideas?