Posts made by stavrosgmtl

@dc42 @Phaedrux I appreciate the help, I rewired the whip and voila it worked. Thank you everyone for your time. I should have rewired it from the start, the config is NOT that hard!

Cheers

fans tested wiring is perfect, replaced anyway, same thing.

@Phaedrux not a bad idea to inspect wiring. Ill do that next.

@Phaedrux m106 works perfectly, except when printing. So before starting a print, m106 works, after a print ends, it works. The identical m106 commands in the gcode are ignored.

So i tested the fan on one of the always on ports, it worked perfectly. I swapped fans, no change.
I tried different duet boards as well. no change.

I did some calibration tweaks to my config recently as I switched to rails, and upgraded to 3.44. I checked the profile gcode vs code that worked in the past. I didn't see anything there.

I downgraded to 3.4, and no change.

So to your point, I think I've narrowed it down to to config or firmware.

I 'll create some small sample gcode now for a 2 layer cube, and get back to everyone.

So in the last week, my part cooling fan0 stopped working on my duet 2 wifi.

I tested the fan always on, perfect. PWM control via m106, no problem. But when actually printing, m106 is ignored. I checked the gcode, it looked fine.

In fact the part fan comes on after a print if you stick a m106 s1, in the post print, after z < 300. I mean at this point I am the holy water stage.

I thought it might have been a profile issue in Simplify3D, kiss slicer had the same problem. If anyone has a Cura profile for a duet2 equipped delta, I'd try that.

I've also swapped the board out of my cr10, no change. Tried versions 3.4 and 3.44.

I am at my wits end. Any help would be greatly appreciated.

m122 output;

11/10/2022, 9:57:47 PM	m122
=== Diagnostics ===
RepRapFirmware for Duet 2 WiFi/Ethernet version 3.4.4 (2022-10-20 16:17:41) running on Duet WiFi 1.02 or later
Board ID: 0JD0M-9P61A-J8PSJ-6J1FJ-3S86S-9SRUS
Used output buffers: 3 of 26 (20 max)
=== RTOS ===
Static ram: 23860
Dynamic ram: 74444 of which 68 recycled
Never used RAM 13708, free system stack 180 words
Tasks: NETWORK(notifyWait,13.2%,242) HEAT(notifyWait,0.0%,333) Move(notifyWait,0.0%,363) MAIN(running,85.9%,440) IDLE(ready,0.9%,30), total 100.0%
Owned mutexes: WiFi(NETWORK)
=== Platform ===
Last reset 00:01:45 ago, cause: software
Last software reset at 2022-11-10 21:56, reason: User, GCodes spinning, available RAM 13564, slot 2
Software reset code 0x0003 HFSR 0x00000000 CFSR 0x00000000 ICSR 0x0041f000 BFAR 0xe000ed38 SP 0x00000000 Task MAIN Freestk 0 n/a
Error status: 0x00
Aux0 errors 0,0,0
Step timer max interval 0
MCU temperature: min 40.2, current 40.9, max 41.3
Supply voltage: min 24.3, current 24.5, max 24.6, under voltage events: 0, over voltage events: 0, power good: yes
Heap OK, handles allocated/used 0/0, heap memory allocated/used/recyclable 0/0/0, gc cycles 0
Events: 0 queued, 0 completed
Driver 0: standstill, SG min n/a
Driver 1: standstill, SG min n/a
Driver 2: standstill, SG min n/a
Driver 3: standstill, SG min n/a
Driver 4: standstill, SG min n/a
Driver 5: 
Driver 6: 
Driver 7: 
Driver 8: 
Driver 9: 
Driver 10: 
Driver 11: 
Date/time: 2022-11-10 21:57:46
Cache data hit count 3654293623
Slowest loop: 9.78ms; fastest: 0.18ms
I2C nak errors 0, send timeouts 0, receive timeouts 0, finishTimeouts 0, resets 0
=== Storage ===
Free file entries: 10
SD card 0 detected, interface speed: 20.0MBytes/sec
SD card longest read time 1.3ms, write time 0.0ms, max retries 0
=== Move ===
DMs created 83, segments created 0, maxWait 0ms, bed compensation in use: none, comp offset 0.000
=== MainDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== AuxDDARing ===
Scheduled moves 0, completed 0, hiccups 0, stepErrors 0, LaErrors 0, Underruns [0, 0, 0], CDDA state -1
=== Heat ===
Bed heaters 0 -1 -1 -1, chamber heaters -1 -1 -1 -1, ordering errs 0
Heater 1 is on, I-accum = 0.0
=== GCodes ===
Segments left: 0
Movement lock held by null
HTTP is idle in state(s) 0
Telnet is idle in state(s) 0
File is idle in state(s) 0
USB is idle in state(s) 0
Aux is idle in state(s) 0
Trigger is idle in state(s) 0
Queue is idle in state(s) 0
LCD is idle in state(s) 0
Daemon is idle in state(s) 0
Autopause is idle in state(s) 0
Code queue is empty
=== Network ===
Slowest loop: 12.73ms; fastest: 0.00ms
Responder states: HTTP(2) HTTP(0) HTTP(0) HTTP(0) FTP(0) Telnet(0)
HTTP sessions: 1 of 8
= WiFi =
Network state is active
WiFi module is connected to access point 
Failed messages: pending 0, notready 0, noresp 0
WiFi firmware version 1.27
WiFi MAC address 48:3f:da:71:af:d2
WiFi Vcc 3.40, reset reason Turned on by main processor
WiFi flash size 4194304, free heap 20952
WiFi IP address 10.0.0.223
WiFi signal strength -36dBm, mode 802.11n, reconnections 0, sleep mode modem
Clock register 00002002
Socket states: 0 0 0 0 0 0 0 0

my config.g

; Configuration file for UltiBots D300VS Delta 3D Printer
; Configuration file for D300vs+ Duet WiFi (firmware version 3.4)

;****** General preferences ******

M575 P1 S1 B57600						; enable support for PanelDue
G90                                     ; send absolute coordinates...
G21                                 	; Work in millimeters 
M83                                     ; ...but relative extruder moves
M550 P"D300vs+"                         ; set printer name
M111 S0 								; debug off
;M555 P2                           		; Set output to look like Marlin
M575 P1 B57600 S1						; Communication parameters for the PanelDue

;****** Network ******
M552 S1                                 ; enable network
M586 P0 S1                              ; enable HTTP
M586 P1 S0                              ; disable FTP
M586 P2 S0                              ; disable Telnet


;****** Drives ******
M569 P0 S0								; Drive 0 goes forwards (X tower)
M569 P1 S0								; Drive 1 goes forwards (Y tower)
M569 P2 S0								; Drive 2 goes forwards (Z tower)
M569 P3 S0								; Drive 3 goes forwards (extruder 1)

M584 X0 Y1 Z2 E3                ; set drive mapping

M350 X64 Y64 Z64 I0 		; Set microstepping to 64 for X, Y and Z and without interpolation
M350 E16 I1                          ; Set microstepping to 16 for extruder stepper with interpolation

M92 X800 Y800 Z800		; Set axis X,Y,Z steps/mm

M566 X1200 Y1200 Z1200 E300			; Maximum instant speed changes mm/minute
M203 X20000 Y20000 Z20000 E3600		; Set Maximum speeds (mm/min)
M906 X1000 Y1000 Z1000 E1400			; Set motor currents (mA)
M84 S30                                                                 ; Set idle timeout

;****** End Stops ******
; 2.x ; M574 X2 Y2 Z2 S1				        ; Set endstop configuration (all endstops at high end, active high)
M574 X2 S1 P"xstop"   					; X min active high endstop switch
M574 Y2 S1 P"ystop"   					; Y min active high endstop switch
M574 Z2 S1 P"zstop"   					; Z min active high endstop switch

;****** Fans ******
; 2.x ; M106 P1 T50 S255 H1				; Set hotend heatsink FAN1 thermostatic control at 50°C
; 2.x ; M106 P2 T70 S255 H0				; Set motherboard FAN2 thermostatic control at 60°C on the bed 

M950 F0 C"fan0" Q500              ; create fan 0 on pin fan0 and set its frequency
M106 P0 S0 H-1                          ; set fan 0 value. Thermostatic control is turned off
M950 F1 C"fan1" Q500              ; create fan 1 on pin fan1 and set its frequency
M106 P1 S255 H1 T50                ; set fan 1 value. Thermostatic control is turned on

;****** Thermistors ******
; 2.x ; M305 P0 T100000 B3950 R4700 L54 H-97				; Kapton bed heater thermistor
; 2.x ; M305 P1 R4700 T100000 B4725 C7.06e-8				; E3D V6 Semitec GT-104 thermistor cartridge
M308 S0 P"bed_temp" Y"thermistor" T100000 B3950 			; define bed temperature sensor
M308 S1 P"e0_temp" Y"thermistor" T100000 B4725 C7.06e-8 	; define E0 temperature sensor



;****** Heater configuration ******
M950 H0 C"bed_heat" T0 ; heater 0 uses the bed_heat pin, sensor 0
M140 H0
M950 H1 C"e0_heat" T1 ; heater 1 uses the e0_heat pin and sensor 1
 
 
;****** Tool definitions ******
M563 P0 D0 H1 F0 				; tool 0 uses extruder 0, heater 1 and fan 0
G10 P0 S0 R0                                         ; Set tool 0 operating and standby temperatures

M92 E850					    	 ; Set **extruder** steps/mm **PLA**
 
 ;****** Z probe and compensation definition ******
; MUST READ: http://www.sublimelayers.com/2017/05/fdffsd.html **STOCK**
; FSRs with JohnSL board Z probe behaves as a switch and is not used for homing any axes
; Change "H25" to "H3" AFTER commissioning your printer
M558 P5 C"!e0stop" H3 F600 T1800		    ; *from FB group
G31 X0 Y0 Z-0.35 P500				     ; More (-) Z is less smooshed, more (+) Z is more smooshed

M557 R100 s20                    ; probe within a radius of 100mm from the center with a mesh spacing of 20mm

;****** Other Settings ******
T0				               ; Select tool 0, the hot end
M501		 		        ; run config-override.g

and finally my config-override.g

; config-override.g file generated in response to M500 at 2022-11-10 19:53
; This is a system-generated file - do not edit
; Delta parameters
M665 L376.000:376.000:376.000 R211.121 H460.672 B140.0 X-0.152 Y-0.161 Z0.000
M666 X1.187 Y-2.268 Z1.081 A-0.59 B0.84
; Heater model parameters
M307 H0 R0.622 K0.287:0.000 D3.92 E1.35 S1.00 B0
M307 H1 R2.029 K0.573:0.000 D6.77 E1.35 S1.00 B0 V24.4
; Workplace coordinates
G10 L2 P1 X0.00 Y0.00 Z0.00
G10 L2 P2 X0.00 Y0.00 Z0.00
G10 L2 P3 X0.00 Y0.00 Z0.00
G10 L2 P4 X0.00 Y0.00 Z0.00
G10 L2 P5 X0.00 Y0.00 Z0.00
G10 L2 P6 X0.00 Y0.00 Z0.00
G10 L2 P7 X0.00 Y0.00 Z0.00
G10 L2 P8 X0.00 Y0.00 Z0.00
G10 L2 P9 X0.00 Y0.00 Z0.00

Here is a starting gcode sample;

G90
M82
M106 S0
M140 S70
M104 S215 T0
M109 S215 T0
M106 S1
G32 ; auto level
M106 S0
; process Process1
; layer 1, Z = 0.200
T0
G92 E0.0000
G1 E-1.5000 F1800
; feature skirt
; tool H0.200 W0.400

and the 2nd layer;

; layer 2, Z = 0.400
M106 S1
G4 P500
; feature inner perimeter

and finally, the end;

; layer end
G91 ; relative positioning
G1 E-1 F300 ; retract the filament a bit before lifting the nozzle to release some of the pressure
G1 Z+1 E-10 F1500 ; move Z up a bit retract filament even more
G28 ; move X to min endstop so the head is out of the way
M106 s0; fan off
M104 S0 ; extruder off
M140 S0 ; bed off
;G4 S300
;M84 ; disable motors

I downgraded to 1.20, i probably confused the error, will retest 1.21 later after my printing is done.

I am getting the same error. Two prints bombed so far.

Firmware Name: RepRapFirmware for Duet 2 WiFi/Ethernet
Firmware Electronics: Duet WiFi 1.02 or later
Firmware Version: 1.21 (2018-03-21)
WiFi Server Version: 1.21
Web Interface Version: 1.21

Motor. TMC2660 ack..

Thank you for the help

D1 is fine. Is there something I can test or replace on board?

Cheers
Stav

@perolalars:

@Camalot977 Would you care to share your sys folder for the CR-10? I have been trying to use the reprap configuration tool but since I have not yet got my cr-10 4 printer I cant tell whats what…

A interested party here too my man. Excited to see this thing in action. My motor config on a late s4 is being a hassle

Hello All,

Bought a s4, wanted to convert to a duet, got motors and endstops working.

But can I ask for people to post some configs? I am having a hard time tuning them.

Any help would be appreciated.

Cheers
Stavros

Me too, the upgrade is going in this weekend

How did it go OP? I am upgrading my CR-10 this weekend

That works on the duet?

I love the duet, saved my butt, thanks!

Loose wire on the bed surface, some good old leaded solder and were back!!! Thanks guys!!!

I so appreciate your forum, you gentleman provide excellent support.

Terminal looks perfect, wires are tightly in there. And the LED comes on when I select a temp…

Guess my bed went?

Stav

After Setting m906 to X1000 Y1000 Z1000 E1400….. to get the extruder stepper running. The heated bed reads active, but does not heat up.

Is there anyway to test if I've blown something on the board?

Ie like a fan mofset?

Stav

@Forgvn77:

I can only speak from my own learning experience. Duet has a steep and sometimes costly (regarding time) learning curve, especially if what you're doing is currently in development But I will say that David and the forum here are a very dedicated and helpful group of people! Stick with it and once you get your rig up and running, you'll definitely be better for it.

Words from my mouth. I love this thing once i understood it. Lot's of little quality of life things that impress me daily.

M500 and config-overide.g save the day, now i get what's going on, tune worked pefectly.

Thanks again
Stav