Hi Gys,
may me help somehow how to thook up an PanelDue V3 7" to an BTT Octopus Pro F429 and how to configure it in System config?
I guess that i fired up the PanelDue Control Board....therefore i have to catch how it works or maybe i have to buy and complete new and other type of Touch Display that maybe fits better without any risk of firing it up 
Many thnkas in advance
Where i may find all necessary information in one shot or rather follow up how to configure and what has to be respected to the WebCam addOn?
Many thx
Danijel
@markz many thanks for that suggestion/information. Will try that as well how to easy and fast after ending observation of the printer to ensure the port again.
Will let you inform how it works
Many thanks
Dan
Many thanks for your replay.
O.k. VPN does that mean that I have to buy software to be able "tunnel" my data through the www?
What about speed? Is there any significant performance lose?
To to your question:
Honestly it makes just sence to observe the print process trough the cam and maybe start a print and stop the process when problems occures.
I guess that just that will be necessary
Many thanks in advance
Hi guys,
May somebody tell me how to set the DWC or rather how to realise the DWC reachable secured from outside the own home network?
Many thanks
Dan
Hi guys,
Is there some good described manual how to configure the motion Webcam plugin?
Many thanks
Dan
@topenga SOLVED....found the zip.file and installed already
Thx
@chrishamm it seems that you are right...My DWC is Version 3.3.0. May someone me show the file i need to upload?!?! Cant find on GitHub the correct files...Thx
Hello all,
tried to install the plugins "Endstop Monitor" as well "MotionWebCam" after updating RFF 3.3 ==> 3.4.0rc2. This is the path to the PlugIns: https://github.com/Duet3D/DSF-Plugins/releases
When trieying to installing the MotionWebCam plugin this message was shown:
"invalid plugin manifest"
When trieying to install the Endstop Monitor plugin this message was shown:
"DuetWeb Control Version 3.3.0 is required" but i do have the V3.3.0 already installed.....
Now im confused......May anybody help me to chack this out?
Best regards
Danijel
Hi Deckingman,
Thx a lot for that detailed explanation. This will help me a lot.......
Best regards
Danijel
Hello Deckingman,
Hello Droftarts,
thanks a lot for replaying that fast. Understood....both sensor types (PT100 and PT1000) are runng with high temperatures...do you know anything concerning low temeprature capabality? Are i'm still able to print ABS/ASA and PETG? What about PT1000...do i need an 4 wired type to conect to the doughter board for better accuracety or is it accurate enaugh by conecting the two wired type directly to the duet?
many thanks
Danijel
Many thanks in advance
Hello all,
currently i have to update my printer to be able to start a project where i have to use technical filaments with the sideeffect that i habe to handle higher temepratures |350-500°C and if possible still temeratures in the Range 225-280 reliable.
May anyone give me some advice what the best temperature sensors for this wide range of temperature sensor is as well i need a snesor that is working propperly with the duet2 board?!?
I have a doughterboard added already to my duet2 wifi as well i have some PT1000 sensors but unfortuneatelly just a two pin version instead of 4 pin. Some time ago i've tried to configre an PT100 without success (it was as well an two pin version).
Many thanks in advance
Danijel
@jay_s_uk said in Hotend FAN1 stops running when Print starts:
M563 P0 S"0.4er Nozzle" D0 H1 F0 ; define tool 0
Hello jay_s_uk said,
thanks a lot....it works....I wonder how long it will take until I'm relly fit due to configuration knowledge!
Great Forum dute to very kind and supportive member!
Danijel
Thanks a lot... Will fix this afternoon and have feedback
Best wishes
Danijel
@jay_s_uk
Auch ..... No..... part cooling FAN0, Hotend FAN1: and electronic FAN2
Thanks for that fast replay......hmmmm M563 is i guess the key?!?
; Configuration file for Duet WiFi (firmware version 3.3)
; executed by the firmware on start-up
;
; generated by RepRapFirmware Configuration Tool v3.3.10 on Thu Dec 30 2021 05:49:28 GMT+0100 (Mitteleuropäische Normalzeit)
; General preferences
M575 P1 S1 B57600 ; enable support for PanelDue
G90 ; send absolute coordinates...
M83 ; ...but relative extruder moves
M550 P"Dan's WonderMachine" ; set printer name
; Network
M551 P"1945" ; set password
M552 S1 ; enable network
M586 P0 S1 ; enable HTTP
M586 P1 S0 ; disable FTP
M586 P2 S0 ; disable Telnet
; Drives
M569 P0 D2 S1 ; physical drive 1 goes forwards
M569 P1 D2 S1 ; physical drive 2 goes forwards
M569 P2 D2 S1 ; physical drive 3 goes forwards
M569 P3 D2 S0 ; physical drive 3 goes forwards
M584 X0 Y1 Z2 E3 ; set drive mapping
M350 X64 Y64 Z256 I1 ; configure microstepping wit interpolation
M350 E16 I0 ; configure microstepping wit interpolation
M92 X320.00 Y320.00 Z6400.00 E693.69435 ;set steps per mm
M566 X700.00 Y500.00 Z100.00 E300.00 ; set maximum instantaneous speed changes (mm/min)
M203 X12000.00 Y12000.00 Z1000.00 E3600.00 ; set maximum speeds (mm/min)
M201 X900.00 Y800.00 Z700.00 E600.00 ; set accelerations (mm/s^2)
M906 X2000 Y2000 Z600 E900 I30 ; set motor currents (mA) and motor idle factor in per cent
M84 S30 ; Set idle timeout
; Axis Limits
M208 X0 Y0 Z0 S1 ; set axis minima
M208 X305 Y305 Z360 S0 ; set axis maxima
; Endstops
M574 X1 S1 P"xstop" ; configure switch-type (e.g. microswitch) endstop for low end on X via pin xstop
M574 Y1 S1 P"ystop" ; configure switch-type (e.g. microswitch) endstop for low end on Y via pin ystop
M574 Z1 S2 ; configure Z-probe endstop for low end on Z
; BLTouch
M950 S0 C"exp.heater3"
M558 P9 C"^zprobe.in" H2.5 F500:100 T12000 ; set Z probe type to bltouch and the dive height + speeds
G31 P500 X0 Y0 Z3.35 P25 ; set Z probe trigger value, offset and trigger height
M557 X5:295 Y50:300 S29:25 ; define mesh grid
; Heatbed
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
; Hotend
M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
M308 S1 P"e1temp" Y"thermistor" T100000 B4100 ; define E0 temperature sensor
M950 H1 C"e1heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S0.85 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S351 ; set temperature limit for heater 1 to 300°C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"PartCooling" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"HotendSink" S0.95 H-1 ; set fan 1 name and value. Thermostatic control is turned off
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 C"Elect" S0.85 H1 T30 ; set fan 2 name and value. Thermostatic control is turned on
; Tools
M563 P0 S"0.4er Nozzle" D0 H1 F0:1 ; define tool 0
G10 P0 X0 Y0 Z0 ; set tool 0 axis offsets
G10 P0 R0 S0 ; set initial tool 0 active and standby temperatures to 0C
; Custom settings are not defined
; Miscellaneous
M501 ; load saved parameters from non-volatile memory
M911 S10 R11 P"M913 X0 Y0 G91 M83 G1 Z3 E-5 F1000" ; set voltage thresholds and actions to run on power loss
T0 ; select first tool7
Since some hours try to figgure out what the faliure is i made 
I'm using Cura and RFF3
Here my Config...may someone can help me because I'm out of ideas.
Thanks a lot
; Heatbed
M308 S0 P"bedtemp" Y"thermistor" T100000 B4138 ; configure sensor 0 as thermistor on pin bedtemp
M950 H0 C"bedheat" T0 ; create bed heater output on bedheat and map it to sensor 0
M307 H0 B0 S1.00 ; disable bang-bang mode for the bed heater and set PWM limit
M140 H0 ; map heated bed to heater 0
M143 H0 S110 ; set temperature limit for heater 0 to 110C
; Hotend
M950 H1 C"e1heat" T1 ; create nozzle heater output on e1heat and map it to sensor 1
M308 S1 P"e1temp" Y"thermistor" T100000 B4100 ; define E0 temperature sensor
M950 H1 C"e1heat" T1 ; create nozzle heater output on e0heat and map it to sensor 1
M307 H1 B0 S0.85 ; disable bang-bang mode for heater and set PWM limit
M143 H1 S351 ; set temperature limit for heater 1 to 300°C
; Fans
M950 F0 C"fan0" Q500 ; create fan 0 on pin fan0 and set its frequency
M106 P0 C"PartCooling" S0 H-1 ; set fan 0 name and value. Thermostatic control is turned on
M950 F1 C"fan1" Q500 ; create fan 1 on pin fan1 and set its frequency
M106 P1 C"HotendSink" S0.95 H-1 ; set fan 1 name and value. Thermostatic control is turned off
M950 F2 C"fan2" Q500 ; create fan 2 on pin fan2 and set its frequency
M106 P2 C"Elect" S0.85 H1 T30 ; set fan 2 name and value. Thermostatic control is turned on
Here you will find all you need.....Just follow the steps carefully!
https://duet3d.dozuki.com/Wiki/Connecting_a_Z_probe#Section_BLTouch
Regarding wiring it's quite easy....take a look there:
https://forum.duet3d.com/topic/9286/need-some-help-getting-the-duet-wifi-bltouch-to-cooperate/7
best regards
Wow nxt-1...... Exactly what I was looking for.... Great and awesome how fast you answer!
Many thanks and wish you a great day
Danijel
Hello all,
where I can find the schematics Diagramms of the 2Wifi v1.04 in special the schematics of the 5 and 3V realization or rather voltage control as well the Fan Controls? Have an demaged Spear Board I would like to try to fix.
Many thanks in advance
Danijel