CR-10S5 Firmware

[Gost101]

@Veti I dont have any start code.

[Veti]

@Gost101

post the start of a g code where the print has been slow

[Gost101]

;FLAVOR:RepRap
;TIME:13024
;Filament used: 5.97829m
;Layer height: 0.12
;MINX:209.345
;MINY:227.132
;MINZ:0.144
;MAXX:279.794
;MAXY:272.866
;MAXZ:48.914
;Generated with Cura_SteamEngine 4.4.1
T0
M190 S50
M104 S210
M109 S210
M82 ;absolute extrusion mode
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate

G28 ;Home

G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

M83 ;relative extrusion mode
;LAYER_COUNT:400
;LAYER:-6

[Gost101]

Regardless of infill, wall thickness and layer height it prints extremely slow.

[Veti]

@Gost101 said in CR-10S5 Firmware:

M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

those lines must be in the start g code of your slicer. thats why the print is slow.
remove them

[Gost101]

@Veti said in CR-10S5 Firmware:It seems to be moving faster but how do I compensate for the extrusion factor? Lines are becoming to small and separating multiple times in one movement.

[Veti]

@Gost101 said in CR-10S5 Firmware:

Lines are becoming to small and separating multiple times in one movement.

is your thermistor set up correctly? are your e steps set up correctly?

[Gost101]

@Veti Yes they are, just got back to my benchy test print ive been gone for almost 6 hours and cura said that it was a 3 hour print. Turns out the printer is not fast still. What should do?

[Gost101]

[Veti]

did you restart the printer after you made those changes? anytime you are printing an old file you will revert the settings and need to reboot.

[PaulHew]

FYI I think the start code Veti is referring to is in your slicer.
If it is Cura.
Settings - Printers - manage printers
Select your printer and click 'Machine Settings'

On that page at the bottom there is a window with Start G-Code

Remove the lines you have been asked to remove.
M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

HTH
Paul.

[Phaedrux]

@Gost101 said in CR-10S5 Firmware:

M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate

Your screen shot shows the top speed as 8.4mm/s which is basically 500mm/min. So I think you still haven't removed the limiting start gcode from cura. Follow the directions that @PaulHew has given.

Once that change is made it will only apply to newly sliced files. All your previously sliced files will have the slow limits set.

[Gost101]

@Veti I did reboot it. I did find that in cura and deleted it. lol

[Gost101]

@Phaedrux @PaulHew @Veti Great confusion this printer has caused me, yet more to learn I must. Sorry I have been watching to much star wars. lol.

[Gost101]

START

M220 S100 ;Reset Feedrate
M221 S100 ;Reset Flowrate
 
G28 ;Home
 
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up
G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
G92 E0 ;Reset Extruder
G1 Z2.0 F3000 ;Move Z Axis up

STOP

G91 ;Relative positioning
G1 E-2 F2700 ;Retract a bit
G1 E-2 Z0.2 F2400 ;Retract and raise Z
G1 X5 Y5 F3000 ;Wipe out
G1 Z10 ;Raise Z more
G90 ;Absolute positionning
 
G1 X0 Y{machine_depth} ;Present print
M106 S0 ;Turn-off fan
M104 S0 ;Turn-off hotend
M140 S0 ;Turn-off bed
 
M84 X Y E ;Disable all steppers but Z

[Phaedrux]

And what speeds are set in cura for printing moves?

[Gost101]

@Phaedrux For this profile it is:

[Gost101]

@Phaedrux Regardless of any adjustments to this, it still takes a long time to print. Even after the changes made.

[Phaedrux]

Can you post a gcode file somewhere for us to see? And perhaps your current config.g file as it is right now?

[Gost101]

Heres the benchy file: Benchy GCode

;config.g
; Created by Gost101 on Saturday, September 28th, 2019 at 18:00 (6:00PM for Civs). 
; This firmware discussion can be found on duet fourm: https://forum.duet3d.com/topic/11964/cr-10s5-firmware/37
; Contact gost1017@gmail.com for more help.
 
; General preferences
G90                                        ; send absolute coordinates...
M83                                        ; ...but relative extruder moves
M550 P"A.C.E."                             ; set printer name
M669 K0                                    ; select Cartesian mode
 
; Network
M551 P"SpaceForceHu2020!!"                 ; set password
M552 S1                                    ; enable network
M586 P0 S1                                 ; enable HTTP
M586 P1 S0                                 ; disable FTP
M586 P2 S0                                 ; disable Telnet
 
; Drives
M569 P0 S1                                 ; X physical drive 0 goes forwards
M569 P1 S1                                 ; Y physical drive 1 goes forwards
M569 P2 S0                                 ; Z physical drive 2 goes backwards
M569 P2 S0                                 ; Z physical drive 2 goes backwards
M569 P3 S0                                 ; E physical drive 3 goes forwards
M584 X0 Y1 Z2 E3                           ; set drive mapping
M350 X16 Y16 Z16 E16 I1                    ; configure microstepping with interpolation
M92 X80.00 Y80.00 Z400.00 E408.30          ; set steps per mm
M566 X500.00 Y500.00 Z30.00 E1500.00      ; set maximum instantaneous speed changes (mm/min)
M203 X10800.00 Y9000.00 Z300.00 E3000.00   ; set maximum speeds (mm/min)
M201 X1000.00 Y1000.00 Z500.00 E3000.00      ; set accelerations (mm/s^2)
M906 X950 Y950 Z850 E900 I30              ; set motor currents (mA) and motor idle factor in per cent
M84 S30                                    ; Set idle timeout
 
; Axis Limits
M208 X0:500 Y0:500 Z0:500                  ; set axis maxima
 
; Endstops
M574 X1 Y1 Z1 S1                           ; set active high endstops
 
; Z-Probe
M558 P0 H5 F120 T6000                      ; disable Z probe but set dive height, probe speed and travel speed
M557 X15:215 Y15:195 S20                   ; define mesh grid
 
; Heaters
M305 P0 T100000 B3950 R4700                ; set thermistor + ADC parameters for the heated bed
M143 H0 S120                               ; set temperature limit for heater 0 to 120C
M305 P1 T100000 B4725 C7.060000e-8 R4700   ; set thermistor + ADC parameters for heater 1
M143 H1 S550                               ; set temperature limit for heater 1 to 550C
 
; Fans
M106 P0 S0 I0 F500 H-1                     ; set fan 0 value, PWM signal inversion and frequency. Thermostatic control is turned off
M106 P1 S1 I0 F500 H1 T45                  ; set fan 1 value, PWM signal inversion and frequency. Thermostatic control is turned on
 
; Tools
M563 P0 D0 H1 F0                           ; define tool 0
G10 P0 X0 Y0 Z0                            ; set tool 0 axis offsets
G10 P0 R0 S40                              ; set initial tool 0 active and standby temperatures to 40C
 
; Custom settings are not defined