Duet3D Logo Duet3D
    • Tags
    • Documentation
    • Order
    • Register
    • Login

    CR-10S5 Firmware

    Scheduled Pinned Locked Moved Unsolved
    Firmware installation
    15
    145
    8.2k
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • JamesMundefined
      JamesM
      last edited by JamesM

      Looking at your config from your post, some of your values are rather low... This is what I have on my Ender 3 which should be similar for you. I think you need to up your speed, accel and jerk(instantaneous speed) on your extruder.

      M350 X16 Y16 Z16 E16 I1 ; Configure microstepping with interpolation
      M92 X80.00 Y80.00 Z400.00 E408.30 ; Set steps per mm
      M566 X500.00 Y500.00 Z30.00 E1500.00 ; Set maximum instantaneous speed changes (mm/min)
      M203 X10800.00 Y9000.00 Z300.00 E3000.00 ; Set maximum speeds (mm/min)
      M201 X1000.00 Y1000.00 Z500.00 E3000.00 ; Set accelerations (mm/s^2)
      M906 X950.00 Y950.00 Z850.00 E900.00 I30 ; Set motor currents (mA) and motor idle factor in per cent
      M84 S30 ; Set idle timeout

      1 Reply Last reply Reply Quote 1
      • Gost101undefined
        Gost101
        last edited by

        @JamesM said in CR-10S5 Firmware: It still prints very slow.
        In addition the nozzle will not retract in the helps of stopping blobs.

        1 Reply Last reply Reply Quote 0
        • Vetiundefined
          Veti
          last edited by

          if you are using cura please post the start g code

          Gost101undefined 2 Replies Last reply Reply Quote 0
          • Gost101undefined
            Gost101 @Veti
            last edited by

            @Veti Do you mean the config code?

            1 Reply Last reply Reply Quote 0
            • Gost101undefined
              Gost101 @Veti
              last edited by

              @Veti I dont have any start code.

              Vetiundefined 1 Reply Last reply Reply Quote 0
              • Vetiundefined
                Veti @Gost101
                last edited by

                @Gost101

                post the start of a g code where the print has been slow

                1 Reply Last reply Reply Quote 0
                • Gost101undefined
                  Gost101
                  last edited by

                  ;FLAVOR:RepRap
                  ;TIME:13024
                  ;Filament used: 5.97829m
                  ;Layer height: 0.12
                  ;MINX:209.345
                  ;MINY:227.132
                  ;MINZ:0.144
                  ;MAXX:279.794
                  ;MAXY:272.866
                  ;MAXZ:48.914
                  ;Generated with Cura_SteamEngine 4.4.1
                  T0
                  M190 S50
                  M104 S210
                  M109 S210
                  M82 ;absolute extrusion mode
                  M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
                  M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
                  M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
                  M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk
                  M220 S100 ;Reset Feedrate
                  M221 S100 ;Reset Flowrate

                  G28 ;Home

                  G92 E0 ;Reset Extruder
                  G1 Z2.0 F3000 ;Move Z Axis up
                  G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
                  G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
                  G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
                  G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
                  G92 E0 ;Reset Extruder
                  G1 Z2.0 F3000 ;Move Z Axis up

                  M83 ;relative extrusion mode
                  ;LAYER_COUNT:400
                  ;LAYER:-6

                  Phaedruxundefined 1 Reply Last reply Reply Quote 0
                  • Gost101undefined
                    Gost101
                    last edited by

                    Regardless of infill, wall thickness and layer height it prints extremely slow.

                    1 Reply Last reply Reply Quote 0
                    • Vetiundefined
                      Veti
                      last edited by

                      @Gost101 said in CR-10S5 Firmware:

                      M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
                      M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
                      M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
                      M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

                      those lines must be in the start g code of your slicer. thats why the print is slow.
                      remove them

                      1 Reply Last reply Reply Quote 0
                      • Gost101undefined
                        Gost101
                        last edited by

                        @Veti said in CR-10S5 Firmware:It seems to be moving faster but how do I compensate for the extrusion factor? Lines are becoming to small and separating multiple times in one movement.

                        Vetiundefined 1 Reply Last reply Reply Quote 0
                        • Vetiundefined
                          Veti @Gost101
                          last edited by

                          @Gost101 said in CR-10S5 Firmware:

                          Lines are becoming to small and separating multiple times in one movement.

                          is your thermistor set up correctly? are your e steps set up correctly?

                          1 Reply Last reply Reply Quote 0
                          • Gost101undefined
                            Gost101
                            last edited by

                            @Veti Yes they are, just got back to my benchy test print ive been gone for almost 6 hours and cura said that it was a 3 hour print. Turns out the printer is not fast still. What should do?

                            1 Reply Last reply Reply Quote 0
                            • Gost101undefined
                              Gost101
                              last edited by

                              Capture.PNG

                              1 Reply Last reply Reply Quote 0
                              • Vetiundefined
                                Veti
                                last edited by

                                did you restart the printer after you made those changes? anytime you are printing an old file you will revert the settings and need to reboot.

                                Gost101undefined 1 Reply Last reply Reply Quote 0
                                • PaulHewundefined
                                  PaulHew
                                  last edited by

                                  FYI I think the start code Veti is referring to is in your slicer.
                                  If it is Cura.
                                  Settings - Printers - manage printers
                                  Select your printer and click 'Machine Settings'

                                  On that page at the bottom there is a window with Start G-Code

                                  Remove the lines you have been asked to remove.
                                  M201 X500.00 Y500.00 Z100.00 E5000.00 ;Setup machine max acceleration
                                  M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate
                                  M204 P500.00 R1000.00 T500.00 ;Setup Print/Retract/Travel acceleration
                                  M205 X8.00 Y8.00 Z0.40 E5.00 ;Setup Jerk

                                  HTH
                                  Paul.

                                  RailCore II - Duet Mini + 1LC, Voron V0.1 - Duet Mini
                                  Voron 2.4 disassembled..... Waiting for the RailCore Mini....

                                  1 Reply Last reply Reply Quote 1
                                  • Phaedruxundefined
                                    Phaedrux Moderator @Gost101
                                    last edited by Phaedrux

                                    @Gost101 said in CR-10S5 Firmware:

                                    M203 X500.00 Y500.00 Z10.00 E50.00 ;Setup machine max feedrate

                                    Your screen shot shows the top speed as 8.4mm/s which is basically 500mm/min. So I think you still haven't removed the limiting start gcode from cura. Follow the directions that @PaulHew has given.

                                    Once that change is made it will only apply to newly sliced files. All your previously sliced files will have the slow limits set.

                                    Z-Bot CoreXY Build | Thingiverse Profile

                                    1 Reply Last reply Reply Quote 0
                                    • Gost101undefined
                                      Gost101 @Veti
                                      last edited by

                                      @Veti I did reboot it. I did find that in cura and deleted it. lol

                                      1 Reply Last reply Reply Quote 0
                                      • Gost101undefined
                                        Gost101
                                        last edited by

                                        @Phaedrux @PaulHew @Veti Great confusion this printer has caused me, yet more to learn I must. Sorry I have been watching to much star wars. lol.

                                        1 Reply Last reply Reply Quote 0
                                        • Gost101undefined
                                          Gost101
                                          last edited by

                                          START

                                          M220 S100 ;Reset Feedrate
                                          M221 S100 ;Reset Flowrate
                                          
                                          G28 ;Home
                                          
                                          G92 E0 ;Reset Extruder
                                          G1 Z2.0 F3000 ;Move Z Axis up
                                          G1 X10.1 Y20 Z0.28 F5000.0 ;Move to start position
                                          G1 X10.1 Y200.0 Z0.28 F1500.0 E15 ;Draw the first line
                                          G1 X10.4 Y200.0 Z0.28 F5000.0 ;Move to side a little
                                          G1 X10.4 Y20 Z0.28 F1500.0 E30 ;Draw the second line
                                          G92 E0 ;Reset Extruder
                                          G1 Z2.0 F3000 ;Move Z Axis up
                                          

                                          STOP

                                          G91 ;Relative positioning
                                          G1 E-2 F2700 ;Retract a bit
                                          G1 E-2 Z0.2 F2400 ;Retract and raise Z
                                          G1 X5 Y5 F3000 ;Wipe out
                                          G1 Z10 ;Raise Z more
                                          G90 ;Absolute positionning
                                          
                                          G1 X0 Y{machine_depth} ;Present print
                                          M106 S0 ;Turn-off fan
                                          M104 S0 ;Turn-off hotend
                                          M140 S0 ;Turn-off bed
                                          
                                          M84 X Y E ;Disable all steppers but Z
                                          

                                          CuraCapture.PNG

                                          1 Reply Last reply Reply Quote 0
                                          • Phaedruxundefined
                                            Phaedrux Moderator
                                            last edited by

                                            And what speeds are set in cura for printing moves?

                                            Z-Bot CoreXY Build | Thingiverse Profile

                                            1 Reply Last reply Reply Quote 0
                                            • First post
                                              Last post
                                            Unless otherwise noted, all forum content is licensed under CC-BY-SA